Prevent cabinet doors from slamming shut with integrated Prevent cabinet doors from slamming shut with integrated soft-close technology from Everbilt. Designed for a full overlay these hinges are retro fit able and allow any level DIYer to do away with the heavy slamming of cabinet doors. The complete overlay leaves your cabinets with a sleek modern look.  More + Product Details Close


Knobs only: The benefit of cabinet knobs is that they are typically less expensive than bar and T-pulls, and they only require one hole to be drilled into your cabinetry. A single cabinet knob can be installed on cabinet doors, but you may want to consider placing two knobs on larger drawers. Cabinet drawers are heavier than doors, therefore you may need that extra knob for ease of use. The minimalistic style of using knobs only for your cabinetry can give a very appealing look to your new kitchen.

Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
White cabinets really help bring out the light and area available in a room. My kitchen is currently really dark and doesn't let much light in. I feel if I were to add windows and make the room a lighter color it would appear a lot happier and feel like I have more room. Thanks for the inspiration I am going to start looking for pieces to make my kitchen lighter like yours!
There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.
Getting the right finish for your kitchen cabinets can make the difference between a good and a great space. The right finish offsets other design choices in your kitchen. For example, you can match your appliances to your hardware finish to create a sophisticated, coordinated look. Alternatively, you can use your kitchen cabinet hardware finishes to show off your fun-loving personality, choosing a bright metal or unique design.
- Catches secure the cabinet door using magnets or rollers. - Latches clip or swing into place and are great for homes with children or curious pets. - Drawer Slides make closing and opening drawers easier and self-closing models prevent damage caused by slamming. - Hinges are available in styles and finishes to match cabinet knobs and pulls. Make sure to match the installation type when replacing existing hinges.
“People come in and say they have a ‘standard’ door,” says Renee Genereux of the Brandino Brass team. “But there is no such thing as standard. You need to know your door thickness, how does it swing, what’s the width, what kind of holes do you have.” Avoid multiple visits to the hardware store because you don’t have all of the information and measurements you need. “We give them all of the questions to answer and then they come back with all of it.” Call Brandino Brass ahead of time to ask what you need to know for your visit or check out the sheet below as handy guideline for getting to know your doors and cabinets better.
Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.

Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five.  I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
If you're having trouble selecting the perfect cabinet hardware, for quality and value, you can’t go wrong with a cabinet hardware sample box. The cabinet hardware sample box lets you try out multiple styles and finishes in your home, select the one you love, then visit homedepot.com or your local Home Depot store to purchase the full amount needed.
Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.
Cabinetmaker Steve Roca replies: Whether you're hanging new doors, as I'm doing here for a hallway cabinet, or swapping out old hinges, concealed or Euro-style hinges are a dream to install. Unlike the butt or knife hinges often used in kitchen cabinets, they can be adjusted along three axes with the turn of a screwdriver, so you can easily fine-tune the door's fit.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
Hi Diane, I am so darned impressed with the work you are doing on your kitchen cabinets. We have high end oak cabinets painted in a washed white finish and they need a refresher too. I am going to follow your lead and try and do them myself. I am a novice at this but, you give such excellent instructions that I feel I can do it, starting in January. I want our island to be a dark, almost blue/black finish and the other cupboards done in white. Love yours. I am going to do the counter tops with the paint (Carrara Marble) if I can find it in Canada. I think Home Depot will sell it. I have one big problem. When we originally had our kitchen done back in 1987, they put corrian edging around the edges and I want it taken off. Do you have any suggestions on what to put there to replace it? A friend suggested putting a wood molding there and just painting it too. I just don’t know if it would stand up. Help! Love your great ideas. Thanks so much, Peggy
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.
“When it comes to hardware, it’s hard to shop on the internet,” says Eric. “Some things that look really good online, look cheap in person and vice versa. Some cheap-looking online items look exquisite in person.” The Brandino Brass team says that not only the look, but the feel of door hardware and cabinet hardware is very important. “You don’t want a handle to poke you or have an awkward grip for your hands,” says Renee.
I am taking on more and more cabinet refresh projects (for hire), and still never tire of the transformations.  My latest project is an oak, galley style kitchen, and I’m digging deeper into ideas to make these older kitchens look more modern.  Paint is obviously a big hitter in terms of updating a kitchen, but let’s talk about something else that is equally powerful – cabinet hinges.
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
Whereas crystal is made primarily of silica and lead oxide, glass is largely composed of silica and soda lime. The lime is the reason glass can have a greenish tint when light is shining through it, whereas crystal is clear. Glass can provide the perfect accent to a room, and is an excellent secret weapon if you are wondering how to add a “pop” without overdoing it.
Rest easy, friends, you can do this, too.  And then, since it looks much better and you are thrilled and at peace with it, you can move on to dreaming about that full kitchen reno you are still working towards… one day.  Or, maybe you will be so happy with the small changes you made that you can cross that idea right off the list and move on to dreaming about making other areas of your home just right.
Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door. 
I’m currently on the hunt for the perfect brass pulls to update my run-of-the-mill silver knobs. But to get a whole sense of what's available at the hardware store these days, I'm looking beyond just brass and test-driving a few other options as well. From handsome black bars to boho porcelain and even DIY leather, these gorgeous hardware options are sure to inspire.
×