New cabinet door hinges are costly, and you can save a substantial amount of money by repainting old hinges yourself. The preparation work will be the most time-consuming part of the process, but skipping this step could cause you more work later. Don't waste time using all-purpose primer; use a rust-inhibiting metal primer to ensure that the paint adheres. A top-quality paint will give the hinges a professional-looking finish.
Installing new Knobs and Pulls are a super easy way to update your kitchen cabinets without spending a fortune. Our kitchen cabinets didn’t even have knobs and pulls installed so I was happy to finally add new hardware. If you’re looking for an easy update for your kitchen by getting new kitchen hardware, you will like my favorite new go-to place for hardware, D. Lawless Hardware.

And why shouldn’t we love them? Not only are they sturdy and virtually maintenance-free, but each stone tells a story that is uniquely independent of humankind. That stone making up your cabinet knob was formed in the hot belly of our planet, hardened to a crust on its exterior and then one day miraculously plucked up by a passing human and turned into a part of your daily life.


I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
We also did that. Our handles are those stainless steel round bars. Loved the look with our white slab door/drawer fronts! Turned out there was big problem with sides of the horizontal drawer pulls snagging pants pockets. So, replaced those with centered flush type steel rectangular pulls that we mounted on the drawers after using router to make mortise holes No more snagging pockets!
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!
At one point I considered trying to update the cabinets with more modern hidden hinges, but after some research I realized that isn’t possible for all cabinet styles and can also be pretty costly.  So instead, I started making a plan to update the older-style hinges we already had.  They started out an aged brass finish.  And not a beautiful antique brass, but more like brass that had been soaking up kitchen grease for 40 years.  Not exactly what I wanted to use on my ‘new’ white cabinets.
Nickel and chrome have about the same level of durability, but chrome is sometimes a bit more expensive.  Brushed or matte finishes hide fingerprints and watermarks better than shiny finishes.  You’ll generally find a lot more hardware options in brushed nickel than in chrome or stainless steel. Poor quality nickel and chrome finishes can peel and flake over time.  Stainless steel, which is usually matte, is the most durable of the silver finishes and as such, is usually the most expensive.  True stainless steel hardware is typically made from a full thickness metal alloy and it’s not just plated on the surface like nickel and chrome are. 
I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
The importance of selecting quality hardware is impossible to overstate. As with many parts of our home, hardware is an investment. We have all seen cabinet knobs that loosen too easily and hinges that wear out. Because hardware is going to receive the bulk of a cabinet’s wear and tear, investing more in it is ultimately investing more in the life of your cabinets.
Choose hardware that will contrast with your cabinets. Accent dark wood with brass, stainless steel, chrome or nickel. Light-colored cabinets provide the perfect background for bronze, enamel or copper with an antique finish. Metal hardware with a satin or highly polished finish can be adapted to a contemporary or traditional decor. Oil-rubbed bronze suggests a more casual style. Consider enamel and glass hardware for a Victorian home. Glass is also available in sleek designs to accent a contemporary setting.
The timeless classics of solid brass styles, futuristic euro-design aluminum pieces, stunning granite and stainless steel combinations, and novelty handcrafted hardware can all be purchased for a fraction of the cost of replacing your entire set of kitchen cabinets. Give your kitchen a new look with the simple replacement of cabinet hardware. Sprucing up the kitchen has never been easier.
Furthermore, hardware attracts the eye like a bright light. Functionality aside, it is the ultimate accent piece — it provides a pop to cabinets and drawers that can make or break the décor of a room. It also keeps the wood of our cabinets and drawers looking fresh by taking the brunt of the natural oils in our hands, which we leave behind every time we reach for the cabinet to grab something.
Aside from polishing, the look of stone hardware is largely in the hands of nature. Though your hardware pieces may all share traits if they come from the same slab of rock, each piece is going to be different. This creates a natural variety in appearance that will add zest to your room. Stone is cool to the touch and looks especially lovely in homes with a woodsy touch.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.

The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Pick a color scheme and stick with it. This tip is twofold, as it helps tremendously in narrowing down your choices while simultaneously expanding your options. Pick a large swath — say, the entire lower half of the kitchen — and commit to a color scheme. If the drawers in your kitchen are white, and all the hardware shares the same type of finish, the presence of different types of knobs and handles will be a pleasant sight, rather than a distraction.
Pulling design from old pharmacies and soda fountains, latch hardware is that without a doubt a nostalgic throwback. Maybe not the most functional if you’re in a hurry, but handy if you’re looking for a little extra security from pets or children. Latches are another hardware type that can easily be mixed and matched, so maybe just keep them to the lesser used cabinets.

“We find it refreshing for people to purchase what they like and what feels good to them, not caring what the ‘Joneses’ have,” says Renee. The Brandino Brass team regularly works with professionals who have their own signature styles. “One architect in town may use the same small knob all over the house all in the same finish for continuity. Another one will use different styles and finishes in each individual room,” says Jessie Isom, Brandino Brass team member. “There is no right or wrong if you like it.”
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
You know I have read so many blogs, articles, and posts about this. I have even emailed some hardware companies like Rockler. I have a hinge that I can’t figure them out, I wanted to upgrade them to something more readily available as 5/8 partial inset hinges are hard to find. Rockler suggested replacing the cabinet doors. I spent over seven months working on redoing my kitchen cabinets.

It's something you could DIY if you wanted to invest the time and energy into it, but I know my strengths and weaknesses. ;-). This sweet, retired woodworker, is charging $300-$400 to drill the holes in the cabinets, provide the hinges, and rehang them (all 23 of them), so I'm feeling like it's a pretty good deal, and the homeowner agrees! I'm really excited to see the finished look!
Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!
×