Hardware can have a huge impact on the look and feel of your kitchen, which is why we often recommend replacing hardware as a quick upgrade for rental kitchens, or when you aren’t able to remodel. So when you’re planning a new kitchen, or a re-design, don’t let your hardware be an afterthought. Here are a few guidelines to help you select the right hardware for your kitchen.
Hanging knobs on a flat-front cabinet is pretty straightforward: You’ll want to position the knob in the bottom corner (for upper cabinets) or top corner (for lower cabinets) of the door. Knobs should be placed equidistant from both sides of the cabinet. A guide like this one can help you to get the measurements right. The exact distance will depend on the look you want and the size of your knobs: Test one or two before you drill a whole kitchen’s worth of holes.
Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.
What if you can’t decide on kitchen hardware? It’s OK to mix and match! Pick patterns and finishes that complement each other and install them in a repeating pattern for a look that is custom to your style. It’s easy to switch up this look as you please. However, this might not impress a potential homebuyer if you choose to sell in the future. Consider updating to more traditional cabinet hardware when it comes time to sell.
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.
Finally, another popular way of opening cabinets without the use of traditional pulls or knobs is through cut-outs in the cabinetry. These are frequently found on custom cabinets where a minimalist look is desired, or where the budget is tight and saving on hardware is desirable. Cut-outs can come in a range of shapes, and are often designed to facilitate ease of opening. 
For Shaker-style cabinets, look for hardware like small round knobs or hardware that feels organic to the craftsman style. I like the idea of brushed nickel or brass for this style of cabinetry. With modern fronts, choose hardware with a sleek and simple design, think matte black or stainless steel, or don’t be afraid to ignore hardware all together and have a custom groove built-in. When planning for a more traditional approach, push the boundaries in your hardware and look for more ornate knobs.

For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.


You might think that after making dozens of tough decisions during your kitchen remodel, something like choosing handles for your cabinets would be easy. Yeah, so not the case. You’ll soon find out that there are more cabinet knob options than there are stars in the sky. But don’t panic. And by all means, don’t make a knee-jerk decision just to get it over with. When I used to make up design and swatch boards, I would remind clients that the hardware matters as much as the big stuff. Remember, you’ll be looking at and touching your kitchen cabinet knobs every single day. So you want to make the right choice. And after all, this is a micro design element that can have macro impact.

Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
After narrowing down your kitchen cabinets options and finally selecting the style that looks the best for your home, you still have to decide on the right decorative hardware for your cabinets. Choosing kitchen cabinet hardware sounds like an easy process, but with the thousands upon thousands of options available, making your final decision can be a bit overwhelming.
Knobs only: The benefit of cabinet knobs is that they are typically less expensive than bar and T-pulls, and they only require one hole to be drilled into your cabinetry. A single cabinet knob can be installed on cabinet doors, but you may want to consider placing two knobs on larger drawers. Cabinet drawers are heavier than doors, therefore you may need that extra knob for ease of use. The minimalistic style of using knobs only for your cabinetry can give a very appealing look to your new kitchen.
Although kitchen cabinet knobs are small objects, keep in mind that one on each cupboard door creates an overall design impact. Further impact can be created by choosing cabinet knobs that contrast in color and texture with the cabinets. If less impact is desired, cabinet knobs may be made of the same material and in the same color as the kitchen cabinets. The most important thing to remember when choosing cabinet knobs to coordinate with cabinets is to keep the kitchen’s overall tone in mind, whether it’s country, elegant, whimsical or traditional.

Use the same guidelines for or your interior doors. If you like the idea of statement door knobs and hinges, go for lots of contrast— dark door knobs and hinges on light doors, for example.  As an aside, interior door levers, which you simply have to push down, are easier for aging hands to operate as compared to door knobs, which you have to twist.


​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.
Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening. 
Thanks Mary. That is a good question. There is another similar product from DecoArt called Metallic Lustre but I am not sure if it is available in Europe either. (Also, I haven’t used it so I can’t say for sure if I would recommend it.) Also, it isn’t exactly the same but silver spray paint can also work. After cleaning the hinges, spray them with spray primer and then follow up with a spray paint in the metallic finish you want.
It's easy to overlook cabinet handles when you're remodeling your kitchen or building a new home. After all, they're fairly small, easy to install and don't cost as much as, say, a refrigerator or new cabinets. Nevertheless, cabinet handles, also called cabinet pulls, and their near kin, cabinet knobs, can make a big difference in the look and utility of your kitchen. You use your cabinet hardware dozens of times a day, and while hardware like cabinet hinges are not highly visible, kitchen cabinet handles are high profile and can add to or detract from the look of your kitchen, depending on how carefully you choose your kitchen cabinet knobs and handles. Keep reading for information on how to choose cabinet handles that will help give your kitchen the look you want.
Shaker style cabinets. The most common style of cabinet offers flexibility in design, and they work well with knobs or cup or bin pulls. Shakers are known for their simplicity and clean lines, so simple hardware is often used, such as round knobs.Traditional nickel or steel knobs or pulls are common, as well as vintage glass or ceramic knobs. Vintage pulls with exposed screws provide a classic touch or industrial feel to a new kitchen with shaker cabinets. Tubular bar pulls — which can be short or long and dramatic — modernize a traditional kitchen with shaker cabinets. Flat bar pulls offer a contemporary edge, while wire pulls keep your décor traditional. Arched and footed bar pulls offer a classic look on shaker style cabinets.
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
When it comes to designing a kitchen inevitably you have to pick out hardware, and these seemingly small details can literally keep you up at night, going back and forth between brass knobs or stainless steel bars. But thankfully, we’re here to help you get a “handle” on the process. Here are the factors you should consider when choosing kitchen cabinet hardware.
×