Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
For oversized cabinetry you’ll obviously want to use larger hardware.  Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized.  For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches.  Some contemporary pulls are even larger than 12 inches.  That measurement is taken from the center of one screw hole to the center of the second screw hole).  Oversized knobs  are 1-1/2” or larger.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
The clean, industrial look of silver produces a calm ambiance, which pairs perfectly with your white cabinets. Silver is also bright enough, where it also stands out on your cabinets and gives your kitchen that shiny and sterile feel. The majority of today’s appliances are stainless steel, so your stainless steel hardware will share that uniform look.
3. Traditionally, your hardware should be the same finish as your kitchen sink faucet. However, mixing and matching metals is on trend in contemporary and transitional homes. Don’t forget to consider your appliances and light fixtures as well. Black appliances look lovely beside bronze or black hardware, while stainless steel and nickel play nicely together. 

Installing new hinges can be easy, but only when choosing the correct cabinet hinge upgrade. The door style, door thickness, and hinge type, all play a role. Once this information is obtained, you should be able to find a soft-close hinge that is a direct retrofit to the existing hinge, or choose one of the many independent dampers and keep your current hinges.

I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!
Swapping these items out is often easy, and Los Angeles-based designer Betsy Burnham says her clients are frequently surprised at the visual impact of something as simple as carefully chosen hardware. Last summer, she added door pulls made of rope tied in small nautical knots to the built-in cabinets at a California beach house, inexpensively adding a dash of personality to the space.
Pick a color scheme and stick with it. This tip is twofold, as it helps tremendously in narrowing down your choices while simultaneously expanding your options. Pick a large swath — say, the entire lower half of the kitchen — and commit to a color scheme. If the drawers in your kitchen are white, and all the hardware shares the same type of finish, the presence of different types of knobs and handles will be a pleasant sight, rather than a distraction.
​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.
I'm glad that you talk about the different hardware options, such as how you can choose something more decorative or if you are more focused on the functionality you want pulls and knobs that are subtle, like silver or clear colored. Knowing what you want would be useful so you can then easily search the various door hardware options online. If you search online, it could help you get more options and you could find stores that focus more on the type of knobs, pulls, and anything else that you're looking for.
We just moved into our home a few months ago and it definitely needed some updating. We decided to start in the kitchen with new appliances. Black stainless beauties 😍 That's when we really noticed how "80's" our kitchen cabinets were! They were in good shape, just wrong color. So we decided to just paint them! The hinges were terribly dirty with a film over them and brass colored. So here's a step by step how I quickly cleaned them and then painted them to match the black stainless appliances....
The homeowner has already installed a new tile backsplash, and will also be replacing the floors with new tile and painting the walls once I’m finished with the cabinets.  But the homeowner was concerned about the hinges standing out against a light cabinet color.  A cabinet refresh is going to help tie the updates together, and when we got to talking about the hinges, I did some research, and found a great local woodworker to help change the hinges from exposed to concealed.
It’s important to choose hardware that will complement the rest of your kitchen décor and accentuate its worthy features. Generally, most people want their cabinet and drawer hardware to coordinate with the handles on their appliances. The colors should work well together, and the finishes shouldn’t clash. Drastically different shapes can also make your kitchen feel cluttered. You should use functionality and your personal preference to approach choosing knobs vs. pulls, but there are a few general guidelines to follow that correlate with your style of cabinets.
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.

A common choice is to use knobs for all drawers and pulls for all doors (or vice versa). The problem with knobs is they are harder to grip and fingernails tend to mar the cabinet door. It is much more comfortable to open a drawer using a pull, which allows the whole hand to grab instead of only your fingertips. We generally use pulls (no nobs whatsoever) in our kitchen designs.  
2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
Consider the style that you have used to decorate your home. Traditional styling indicates a need to use cabinet hardware that has a brushed finish. Pewter, nickel, and polished brass blend well with traditional styling, although other styles will look nice as well. Perhaps you would prefer to contrast the traditional cabinets with some hardware that leans more toward the unique and modern.
Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
Aesthetically when do you choose to a long handle or a cabinet door vs. a button size knob. This does require some finesse and doing some drawings to get it just right, but here are few tips to take into consideration. You may want to lean more towards small knobs and handles if you are going for a more contemporary style in your kitchen space. Often mixing and matching round knobs with drawer pulls work well in these style of kitchens. A longer handle may be used in a more modern kitchen for a more polished look in a space, while having too many small knobs would feel cluttered for this type of kitchen. In a transitional space, you may want to select one style of hardware and then make that one particular style of hardware larger or smaller depending on where it’s going in the kitchen. For example you would have larger handles for your refrigerator and pantry doors, but a smaller version of the same knob for the upper cabinets in your kitchen area above the refrigerator.
×