Want sleek form? Want functionality at its finest? Say hello to handles. Handles for white cabinets allow a firm and full grip to easily pull open or push close any cabinet door. Handles come in a cornucopia of shapes and sizes to male for a match with your kitchen style. Handles offer installation flexibility, with vertical and horizontal options, which allows for additional detailing for your white cabinets.
I would like to use a hinge similar to the wrap around no mortise Amaroc 3175s but am disappointed to learn the poor reviews ….sloppy….bent…flimsy…not worth it…low qc import. Perhaps they were better in the past! I would be most greatful if you could recommend a better quality hinge of that style. Alternatively,Can the full inset euro cup hinge be adapted to a face frame cabinet by building out the inside lip ^
I watch you every Sunday morning. I used to help run a construction co. here in Knoxville,TN. I am now my Moms cargiver(87). I lost my dear sweet husband last November. I am trying to sale my house. I am just stressed trying to find replacement wrap-around hinges and pulls for my kitchen and bath. I also am going to replace my laminate tops. Do you have any sources I should check. You two remind me of my sweet dad and me from years ago. Please HELP!!!!!!
One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
Hello Mr. TretheweyMy name is terry cotto, when we built our beautiful home 16 years ago, in Sierra Madre Ca I had my claw tub installed,( my child hood remembrance) It appears, that the claw legs of the tub were not installed properly, and one leg fell off , tub was slightly tipping to the right. I had a handyman come over and reinstall the claw legs, tighten so this would not happen again. The other day, while I was bathing I noticed the seal of the drain on the outside rubber was not laying properly, plus it was leaking, ( I think this was due to the leg falling off and unbalancing the ring. Well, now I really don't know what to do about that. I believe the thing to do is remove the cover off the top drain , ok, but than what do I have to move the claw tub, impossible. How do I replace the rubber of the outside of the top drain pipe, it appears to be brittle. (Not good)Please answer my questions, and I will hire the handy man again to help me. Thank you. I have learned so much from T.O.H weekly shows, I am a loyal fan at 75. I tell my 80 year old husband, you need to watch these shows with me, and we can do it ourselves, the right way. God Bless you all for the great job your doing, I need to know how to do it right, so it doesn't happen again. a picture would be good, I can see exactly how its done?

What color will your appliances be? What about your lighting? Your faucet? For some people, matching hardware to appliances may not be particularly important—we’ve seen plenty of kitchens with brass pulls and stainless appliances. But if you like everything to coordinate, consider the whole kitchen when you pick the color of your pulls. (If your appliances are stainless and you don’t particularly like the look of silver pulls, black hardware makes for a harmonious look that isn’t too matchy-matchy).
Finally, another popular way of opening cabinets without the use of traditional pulls or knobs is through cut-outs in the cabinetry. These are frequently found on custom cabinets where a minimalist look is desired, or where the budget is tight and saving on hardware is desirable. Cut-outs can come in a range of shapes, and are often designed to facilitate ease of opening. 
Although kitchen cabinet knobs are small objects, keep in mind that one on each cupboard door creates an overall design impact. Further impact can be created by choosing cabinet knobs that contrast in color and texture with the cabinets. If less impact is desired, cabinet knobs may be made of the same material and in the same color as the kitchen cabinets. The most important thing to remember when choosing cabinet knobs to coordinate with cabinets is to keep the kitchen’s overall tone in mind, whether it’s country, elegant, whimsical or traditional.
There is a lot of misunderstanding when it comes to crystal. Upon first glance, it looks like glass, but it is in fact of higher quality and clarity, and its chemical composition is markedly different. Contrary to what its name suggests, crystal is not crystalline on a molecular level — that is, its molecules are not arranged in a rigid, repeating structure.
Finally, another popular way of opening cabinets without the use of traditional pulls or knobs is through cut-outs in the cabinetry. These are frequently found on custom cabinets where a minimalist look is desired, or where the budget is tight and saving on hardware is desirable. Cut-outs can come in a range of shapes, and are often designed to facilitate ease of opening. 
At a home renovation in Connecticut, cabinet fabricator Michael Madore experimented with what he calls an "aggressive" metal-sanding process to pull out the grain from the whitewashed oak plywood. For the hardware-free cabinets, Julie Salles Schaffer looked to a drawer pull detail derived from Giò Ponti’s work—though she admits the radial edging is an effect entirely her own.
First, you’ll want to do a thorough count of all your doors and drawers to make sure you know exactly how many new pulls and knobs you’ll need. To streamline the project, match your new hardware’s spread to the distance between the existing screw holes (you may need a tape measure). Or you can just take one of the old pulls with you to the store to shop.
I mentioned to my super-smart carpenter brother, Mike, that I was wanting to update my hinges but was afraid of ruining my doors in the process.  I watched a YouTube video of DIYer who tried to install hidden hinges, and I’ll be polite and just say that the outcome was not a good one. Thus my fear. The place I ordered my new cabinets from couldn’t order replacement doors, so this was a one-shot deal.
Thanks, Marty! You have a joyous looking kitchen/dining room – so beautiful! LOVE it! Not at all stiff and cookie-cutter, but with real individual style! An inspiration today. Your timing is perfect. We have our IKEA kitchen done, except for countertops and backsplash tiling. (We’ve been using Masonite board for a makeshift countertop. Not too bad.) The whole look of our open kitchen/dining room is pleasant, at this point, but bland. Pale minty-grass green walls, blonde (birch) cabinets, warm medium oak floors. Now for putting in some details! YAY! The scary part: Now what? Yikes!! Marty to the rescue with a reassuring article. THANKS! Here we go……
Sometimes brass finishes can be difficult to match since there are so many types (unlacquered, satin, antique, polished, etc.). Generally, you just have to order samples to see everything together. However, I will say that you should stay away from polished brass - it gives a very 80s vibe! Unlacquered brass starts shiny, but has a richer tone that gives a beautiful patina over time. For a more modern brass look, stick with the satin finishes!
Dreamy DIY: Have you ever seen something that makes you want to break out the craft kit and get to down to business? Well these leather drawer pulls with brass rivets are so luxuriously handsome it makes us want to rip out and redo every single pull in the house. I can only imagine how delightful these will begin to look when worn with use — a little imperfection to balance and roughen up such a posh space.
×