- Catches secure the cabinet door using magnets or rollers. - Latches clip or swing into place and are great for homes with children or curious pets. - Drawer Slides make closing and opening drawers easier and self-closing models prevent damage caused by slamming. - Hinges are available in styles and finishes to match cabinet knobs and pulls. Make sure to match the installation type when replacing existing hinges.
What they are: An upside-down cup-shaped pull popularized in the mid-19th century. Bin or cup pulls are a popular choice for giving a kitchen a minimalist, vintage feel, just like on these Shaker-style cabinets and drawers. Shakers originally used wood pegs, usually made from maple, cherry or pine, in keeping with their preference for simplicity and austerity. But these cup-shaped drawer pulls are considered Shaker style today, and look clean and understated along with small knobs for the doors.
On the very last warm-ish day of the year, I laid out all the drawers and doors and got my painting on with my paint sprayer. That thing is the bomb! I had them all primed with Zinsser oil based primer within 15 minutes. Then I waited a couple of hours before painting the final coats. I used Sherwin Williams oil based ProEnamel in Alabaster for the upper cabinets and Sherwin Williams contractor grade oil based paint color matched to Benjamin Moore’s Huntington Green.
There is a lot of misunderstanding when it comes to crystal. Upon first glance, it looks like glass, but it is in fact of higher quality and clarity, and its chemical composition is markedly different. Contrary to what its name suggests, crystal is not crystalline on a molecular level — that is, its molecules are not arranged in a rigid, repeating structure.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
If you have a removable island or a butcher block in your kitchen, an easy way to make that extra piece look cohesive with the rest of your kitchen décor is by adding coordinating cup and cabinet pulls to drawers and doors. This addition will make your island look purposeful and blend it with the rest of your kitchen cabinets — even if the finish or countertop is different.
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
In line with our new content direction, Architizer is highlighting a different building-product and how to specify it. This week’s topic is Kitchen Cabinetry. If you’re looking for the perfect kitchen cabinetry for your next project, search for it on Architizer’s new network marketplace for building-products. Click here to see if you qualify. It’s free for architects.
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.
These industrial-feeling pulls are a blend of colonial and Arts and Crafts, and come in a wide variety of finishes. While these black ones are a good choice with the black appliances and lighting, don’t feel your knobs must match all the finishes in your kitchen; it’s OK to mix things up. Just don’t mix the knobs and hinges on the same door; those definitely should be coordinated so one doesn’t detract from the other.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
Good morning and happy Monday, lovely people! I hope y’all had a wonderful Thanksgiving week. Ours was a little on the insane side, but it ended perfectly. We moved to our new house {Memaw’s house} a little over a week ago. It was crazy getting settled just in time to host our family’s Thanksgiving dinner. It was hard without Memaw. Tears came easily and our family time was just really sweet. I’m very thankful.

The homeowner has already installed a new tile backsplash, and will also be replacing the floors with new tile and painting the walls once I’m finished with the cabinets.  But the homeowner was concerned about the hinges standing out against a light cabinet color.  A cabinet refresh is going to help tie the updates together, and when we got to talking about the hinges, I did some research, and found a great local woodworker to help change the hinges from exposed to concealed.
Hopefully you drilled for the hinges in the same location on every door, if so, then this should be simple. You really just need to measure for the top hinge. I installed my top hinge 4” down from the top of the door, so I measured 3 ½” down from the inside top of the face frame (3 ½” + ½” overlay = 4”). This step is a team effort, one person to hold the door and another person to attach the hinge to the face frame.
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
I’m currently on the hunt for the perfect brass pulls to update my run-of-the-mill silver knobs. But to get a whole sense of what's available at the hardware store these days, I'm looking beyond just brass and test-driving a few other options as well. From handsome black bars to boho porcelain and even DIY leather, these gorgeous hardware options are sure to inspire.
×