For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
Before you get to hardware, it’s crucial to select your cabinet doors. The type of door you select will influence the style tremendously. The most popular styles of cabinet doors at the moment are Shaker, traditional, and modern. A Shaker-style cabinet front is a utilitarian design, with four rails and one middle, slightly recessed, center panel. It’s clean and simple design that can work well with most kitchen styles.
Getting the right finish for your kitchen cabinets can make the difference between a good and a great space. The right finish offsets other design choices in your kitchen. For example, you can match your appliances to your hardware finish to create a sophisticated, coordinated look. Alternatively, you can use your kitchen cabinet hardware finishes to show off your fun-loving personality, choosing a bright metal or unique design.
Cabinetmaker Steve Roca replies: Whether you're hanging new doors, as I'm doing here for a hallway cabinet, or swapping out old hinges, concealed or Euro-style hinges are a dream to install. Unlike the butt or knife hinges often used in kitchen cabinets, they can be adjusted along three axes with the turn of a screwdriver, so you can easily fine-tune the door's fit.
3. Know when to use knobs over pulls. In traditional and country kitchens, putting a knob on a cabinet is not uncommon. In fact, with many cabinets, knobs may a better option than pulls. How do you know the difference? When kitchen cabinets are ornate or finely detailed, go with a knob rather than a pull. A knob is smaller and simpler and doesn’t take attention away from the design of the cabinets.
Sandra, I’m so glad that I came across your blog! You’ve given so much great information that I can use every day in my job doing kitchen cabinet sales. And then there’s the whole DIY part for me personally! I’m really hoping that you can answer my question, though. I have a customer who is refacing her cabinets. She has frameless cabinets and used to have exposed hinges. She wanted concealed hinges so we had the hinge holes drilled 1″ (center) from the edge. She has her new doors but when she hangs them, there’s a 1/4″ gap between the door and center stile, even after adjusting them. We were using full overlay hinges. Can you advise which type of overlay hinge to use and how to rectify the gap? Thanks so much!
For pulls on a flat front cabinet, the bottom corner of the pull should be equidistant from both sides of the cabinet. For Shaker-style cabinets, the same rules apply as with knobs: center the pull on the vertical stile, with the bottom of the pull even with the top of the horizontal stile (or the top even with the bottom of the horizontal stile, for a lower cabinet). These aren’t hard and fast rules—you may want to adjust them depending on what looks best for your cabinets and hardware—but they’re a good place to start.
You’ll also want to think about how visible your hinges will be—do you want them to be a major design feature and mounted directly to both the outside of the frame and the outside of the cabinet, known as a surface-mounted hinge? Or take a more minimalist design approach and have them virtually invisible from the outside when the cabinets are closed, known as a concealed hinge? Are you worried about the noise of cabinet doors closing, and think that soft-closing hinges are important?
A common choice is to use knobs for all drawers and pulls for all doors (or vice versa). The problem with knobs is they are harder to grip and fingernails tend to mar the cabinet door. It is much more comfortable to open a drawer using a pull, which allows the whole hand to grab instead of only your fingertips. We generally use pulls (no nobs whatsoever) in our kitchen designs.
Once you’ve worked out which types of hardware are comfortable to use, it’ll be time to start thinking about shapes in relation to the shape of your cabinetry. In general, knob and pull styles should be matched to kitchen cabinet styles. What this means is if you have selected a plain cabinet style, for example, shaker or flat, ultra-modern doors, then you’ll want square, plain hardware to match — perhaps something like Emtek’s brass bar knob or a similar style. Recessed panel doors or doors with curving and intricate trim will often do well with more ornate hardware styles.
Okay, I haven’t even finished reading this post, but I just have to comment. First of all, I think you are awesome. I have been wanting all kinds of things done to my house, and my husband is pretty capable, but very busy, and far less interested in house things than I am. I just look at the things you do, and I think how I can certainly learn to tackle more of the things that I want to. Second, a post like this is so helpful. I know it takes time to write and I just appreciate the education so much. So, thank you so much for being awesome, and also giving awesome-ness lessons… 🙂
What kind of new hardware should you install in your updated kitchen? There are so many choices out there it can be overwhelming. Knobs or Pulls? Nickel or Brass? Will you be able to see the holes from the old hardware? Because I am being asked these questions on a daily basis I’ve put together a general guide to updating hardware and have included some of my favorites to share with you.