Personal preference is very important when deciding whether you want a knob or pull. Your hardware should be in keeping with the style of your kitchen, but it must be comfortable to use, too. Carefully check out the knobs or pulls you are thinking of buying. Place them against cabinetry, then see how they fit your hand. Are they the right size and shape for you?
Linda, great questions! I have only had my rub n buffed hinges in use for a few weeks so far so I can’t say much for long term use yet. I can say that I haven’t had a problem with it rubbing off, but I did have to be really careful hanging my cabinet doors because I noticed that it did rub off on the white paint if I wasn’t careful. (The few spots where that happened, I just touched up the white paint.) I also didn’t have a problem getting it to shine – but I was going for a brushed nickel look which isn’t super shiny. I don’t know that you could get it shiny enough to be a chrome looking finish. Overall I have been really happy with it but I will be sure to share an update after more time passes.

2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
Interior Door knobs and levers can range from less than $20 to $200.  You can find cabinet knobs and pulls from less than $2 each to more than $20 each.     Solid knobs and pulls are better quality than hollow hardware.  Although you generally get what you pay for with hardware, if your budget is tighter, you might want to choose less expensive cabinet hardware since it’s relatively easy for homeowners to trade it out for better quality hardware in the future.
One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.
You might think that after making dozens of tough decisions during your kitchen remodel, something like choosing handles for your cabinets would be easy. Yeah, so not the case. You’ll soon find out that there are more cabinet knob options than there are stars in the sky. But don’t panic. And by all means, don’t make a knee-jerk decision just to get it over with. When I used to make up design and swatch boards, I would remind clients that the hardware matters as much as the big stuff. Remember, you’ll be looking at and touching your kitchen cabinet knobs every single day. So you want to make the right choice. And after all, this is a micro design element that can have macro impact.
Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less.   The most common pull sizes for standard cabinetry are 3”,  4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches.  Standard knob sizes are less than 1.5 inches in diameter.
Cliffside is one company that works exclusively with high-quality producers who make sturdy, kiln-fired glass. This glass comes in many different colors to suit your palette, as well as different shapes and sizes. Because the glass is strong, it can stand up to the rigors of dropped kitchen items, quick yanks and more. This durability also means it can be used for more than just knobs — there are glass handles available as well.
Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.
Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!
There it is, our top 16 knobs and pulls. We were surprised there weren't any on-trend satin brass options on the list. While we've seen an up-tick in brushed and satin brass hardware's popularity, these tried-and-true stainless steel, satin nickel, and oil rubbed bronze knobs and pulls are still leading of the pack. It just goes to show that not everyone is a trend-follower. Choose your kitchen design details based on your tastes, because the trends will always change anyway!
×