The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Black was a great color choice for the bin pulls used here on stained wood cabinetry. When choosing knobs, hold them against various finishes to see which color looks best. You may have seen a photo of a knob you love in polished brass, but with a different cabinet door color than the ones you actually own. Bin pulls come in almost infinite other finishes as well, including chrome, oil-rubbed bronze, cast iron and brass.
Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door. 

I mentioned to my super-smart carpenter brother, Mike, that I was wanting to update my hinges but was afraid of ruining my doors in the process.  I watched a YouTube video of DIYer who tried to install hidden hinges, and I’ll be polite and just say that the outcome was not a good one. Thus my fear. The place I ordered my new cabinets from couldn’t order replacement doors, so this was a one-shot deal.
As latches like these are elements that people come into contact with every day — literally gripping them for support or activating them with a gentle nudge — architects should keep both aesthetics and functionality in mind when specifying these seemingly simple components. To help you as you search for kitchen hardware on Source, here are a few savvy choices that fit well with modern clean spaces; ones that, even when situated in repetitive rows, won’t take attention away from sleek cabinetry design:
I would like to use a hinge similar to the wrap around no mortise Amaroc 3175s but am disappointed to learn the poor reviews ….sloppy….bent…flimsy…not worth it…low qc import. Perhaps they were better in the past! I would be most greatful if you could recommend a better quality hinge of that style. Alternatively,Can the full inset euro cup hinge be adapted to a face frame cabinet by building out the inside lip ^
Specializing in hardwood furniture, trim carpentry, cabinets, home improvement and architectural millwork, Wade Shaddy has worked in homebuilding since 1972. Shaddy has also worked as a newspaper reporter and writer, and as a contributing writer for Bicycling Magazine. Shaddy began publishing in various magazines in 1992, and published a novel, “Dark Canyon,” in 2008.
Thanks Mary. That is a good question. There is another similar product from DecoArt called Metallic Lustre but I am not sure if it is available in Europe either. (Also, I haven’t used it so I can’t say for sure if I would recommend it.) Also, it isn’t exactly the same but silver spray paint can also work. After cleaning the hinges, spray them with spray primer and then follow up with a spray paint in the metallic finish you want.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
New cabinet door hinges are costly, and you can save a substantial amount of money by repainting old hinges yourself. The preparation work will be the most time-consuming part of the process, but skipping this step could cause you more work later. Don't waste time using all-purpose primer; use a rust-inhibiting metal primer to ensure that the paint adheres. A top-quality paint will give the hinges a professional-looking finish.
The style of cabinet hardware you pick will depend a great deal on the style of your kitchen, and also on the kind of cabinets you choose. Traditionally styled cabinets with more intricate face profiles call for traditional hardware: Cabinets with more simply styled or completely flat faces look best with minimal, streamlined knobs and pulls. Some very modern cabinets don’t require hardware at all: Instead, they have grooves on the edges of the door, or open by push latches.
Knobs only: The benefit of cabinet knobs is that they are typically less expensive than bar and T-pulls, and they only require one hole to be drilled into your cabinetry. A single cabinet knob can be installed on cabinet doors, but you may want to consider placing two knobs on larger drawers. Cabinet drawers are heavier than doors, therefore you may need that extra knob for ease of use. The minimalistic style of using knobs only for your cabinetry can give a very appealing look to your new kitchen.
Eight staircases?!?Nothing says 'stupid' quite as much as that!Not being critical of the crew, but between the 'historical society' that dictates what you can and can't do (but happily send you the bill) and over the top designs that will prove to be idiotic just makes me shake my head in disbelief.This certainly won't be a house where you can 'age in place'.
Thanks Mary. That is a good question. There is another similar product from DecoArt called Metallic Lustre but I am not sure if it is available in Europe either. (Also, I haven’t used it so I can’t say for sure if I would recommend it.) Also, it isn’t exactly the same but silver spray paint can also work. After cleaning the hinges, spray them with spray primer and then follow up with a spray paint in the metallic finish you want.
Contemporary kitchens have sleek lines, very little ornamentation and minimalistic colors. So, for a contemporary style kitchen, it is wise to choose hardware that is simple and streamlined. Linear bar handles with straight lines or curved barrel handles are the perfect choice. Since stainless steel appliances are a hallmark of a contemporary kitchen, you can also select handles for your cabinetry in a similar style and finish as your appliance handles. 
Aesthetically when do you choose to a long handle or a cabinet door vs. a button size knob. This does require some finesse and doing some drawings to get it just right, but here are few tips to take into consideration. You may want to lean more towards small knobs and handles if you are going for a more contemporary style in your kitchen space. Often mixing and matching round knobs with drawer pulls work well in these style of kitchens. A longer handle may be used in a more modern kitchen for a more polished look in a space, while having too many small knobs would feel cluttered for this type of kitchen. In a transitional space, you may want to select one style of hardware and then make that one particular style of hardware larger or smaller depending on where it’s going in the kitchen. For example you would have larger handles for your refrigerator and pantry doors, but a smaller version of the same knob for the upper cabinets in your kitchen area above the refrigerator.
×