One of the first reccomendations I give on choosing hardware, is on wide drawers. Go with a single larger handle especially in the kitchen. The kitchen is a busy area and users find themselves with something in their hand when they go to open a drawer with the free hand. If there are 2 pulls on a drawer, just using one will end up tweaking the drawer in the long run. When I begin to look for a hardware collection always look at the range of sizes in that collection. I like the rule of the larger the drawer the larger the handle... or the more weight the drawer will hold the wider the stance should be that the handle provides.
Consult with a contractor or a knowledgeable salesperson about which hinges will work with your doors. If your doors are flush with the cabinets, butt hinges can be used. They are lower in price than others but do not self-close. European hinges are installed on full overlay, frameless or inset doors. They are widely used because of their ease of installation and ability to be adjusted once in place. These hinges self-close. Partial wraparound hardware will support larger doors, but it does not self-close. Several other types hinges are available. The construction of your door, ease of installation and price will need to be considered. .
Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.
What if you can’t decide on kitchen hardware? It’s OK to mix and match! Pick patterns and finishes that complement each other and install them in a repeating pattern for a look that is custom to your style. It’s easy to switch up this look as you please. However, this might not impress a potential homebuyer if you choose to sell in the future. Consider updating to more traditional cabinet hardware when it comes time to sell.
Prior to making the purchase of your new cabinet hardware, take some careful measurements of the existing hardware. Write down sizes, as well as the spacing of the screws. This should eliminate the need to drill new holes. Accurate measurements are essential to avoid additional work or the need to return and exchange your hardware purchase. In fact, it is a good idea to bring some of your old hardware with you for size comparison purposes, unless you are shopping online for your hardware. In that case, simply have the hardware next to you.
If you have a removable island or a butcher block in your kitchen, an easy way to make that extra piece look cohesive with the rest of your kitchen décor is by adding coordinating cup and cabinet pulls to drawers and doors. This addition will make your island look purposeful and blend it with the rest of your kitchen cabinets — even if the finish or countertop is different.
At one point I considered trying to update the cabinets with more modern hidden hinges, but after some research I realized that isn’t possible for all cabinet styles and can also be pretty costly. So instead, I started making a plan to update the older-style hinges we already had. They started out an aged brass finish. And not a beautiful antique brass, but more like brass that had been soaking up kitchen grease for 40 years. Not exactly what I wanted to use on my ‘new’ white cabinets.
I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
That being said, buying every make and model turned out to be a good idea. I was pretty pumped when I installed my first door…until I shut the door and there was a gap the size of Kansas where the door didn’t cover my opening. I should have taken a picture because it was pretty hilarious-looking. Wrong hinge. So I removed the 1 1/4″ overlay hinge, installed the 1/2″ overlay and was good to go. The holes that need to be drilled in the door will be the same in size, depth and location regardless of your overlay measurement.
Thanks Mary. That is a good question. There is another similar product from DecoArt called Metallic Lustre but I am not sure if it is available in Europe either. (Also, I haven’t used it so I can’t say for sure if I would recommend it.) Also, it isn’t exactly the same but silver spray paint can also work. After cleaning the hinges, spray them with spray primer and then follow up with a spray paint in the metallic finish you want.
We also painted our kitchen cabinets white, and I love the crispness of white cabinets. We used latex paint since we ended up doing most of the work while I was pregnant/nursing a newborn and I didn’t want to deal with the oil-based chemicals and odors. It’s definitely not ideal–the hard, oil-based finish is much more practical for kitchens and cabinets. I’m not a perfectionist so it doesn’t bother me (too much!), but I would definitely recommend taking the time to do oil like you did–yours should last forever 🙂
Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
The choice between cabinet pulls and knobs isn’t easy — both come with positives and negatives. Keep in mind that you’ll be using your knobs or pulls every day. Whatever you choose should feel natural in your hand and flow with the décor of the room. You should consider your kitchen’s décor and style, the look you want to achieve, your budget, ease of cleaning, ease of use, the weight of your drawers and more.
The first thing you need to consider when looking for new cabinet hardware is the overall look you would like for your kitchen. There are literally thousands of drawer pulls and cabinet knobs to choose from, so you need a starting point. Many cabinet styles are easily adaptable to any style of knobs — modern, traditional or even funky. Spend some time gathering pictures of kitchens you like from home magazines to help you choose a style that suits your tastes.
You know I have read so many blogs, articles, and posts about this. I have even emailed some hardware companies like Rockler. I have a hinge that I can’t figure them out, I wanted to upgrade them to something more readily available as 5/8 partial inset hinges are hard to find. Rockler suggested replacing the cabinet doors. I spent over seven months working on redoing my kitchen cabinets.
Updating certain hardware pieces throughout your kitchen is a simple change that can have a big impact on the overall look of your kitchen. Replacing basic ceramic or plastic knobs on your cabinets with heavy-duty stainless steel or brass knobs can give your kitchen cabinets a whole new refreshed style. Depending on the look you’re trying to achieve in your kitchen, you’ll find metal cabinet knobs that range in aesthetics from simple and contemporary, to ornate and decorative.
Below and above the sink can be two different color schemes. Don’t worry, you can mix and match more than you might think and still obey the laws of symmetry. It can provide a sunny, uplifting splash to have a lighter color above the level of the countertops, such as a warm brass or gold. Particularly with items like faucets and sconces, a lighter color around eye level will create a happy glow.
When I’m talking about metals, I consider the silver metals as one grouping. So, when you have stainless appliances (silver), a chrome faucet (silver) and brushed nickel lighting (silver) those all count as one metal in my book- SILVER. I personally think Nickel is the most timeless of the metals. Brass has really gained in popularity with interior designers, but is probably a trendier choice. I’ve seen a rise in the popularity of black hardware especially in this age of farmhouse- EVERYTHING (Thanks Chip and Joanna). I think every room in your house should have a little black in it, so if you can bring in the black with your second metal in your kitchen, DO IT!!