Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
Custom kitchen cabinetry doesn’t come cheap, but if you’re planning to stay put in your home for a long while, it’s worth spending to get exactly what you want, including the built-ins that enable you to live clutter-free. At the other end of the spectrum, we show you ways to modify Ikea kitchen components for a custom look (we’ve found almost a dozen new companies that offer doors to pair with Ikea’s cabinets).
It's something you could DIY if you wanted to invest the time and energy into it, but I know my strengths and weaknesses. ;-). This sweet, retired woodworker, is charging $300-$400 to drill the holes in the cabinets, provide the hinges, and rehang them (all 23 of them), so I'm feeling like it's a pretty good deal, and the homeowner agrees! I'm really excited to see the finished look!
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
Once you’ve worked out which types of hardware are comfortable to use, it’ll be time to start thinking about shapes in relation to the shape of your cabinetry. In general, knob and pull styles should be matched to kitchen cabinet styles. What this means is if you have selected a plain cabinet style, for example, shaker or flat, ultra-modern doors, then you’ll want square, plain hardware to match — perhaps something like Emtek’s brass bar knob or a similar style. Recessed panel doors or doors with curving and intricate trim will often do well with more ornate hardware styles.
The timeless classics of solid brass styles, futuristic euro-design aluminum pieces, stunning granite and stainless steel combinations, and novelty handcrafted hardware can all be purchased for a fraction of the cost of replacing your entire set of kitchen cabinets. Give your kitchen a new look with the simple replacement of cabinet hardware. Sprucing up the kitchen has never been easier.
Robyn and Sam’s home in Toronto is an all-white, minimal lover’s dream. Intentionally kept simple and streamlined, it has just the essentials. Their kitchen is a great example of a minimal and modern space done right. It’s also a great blank canvas to play with to show you more examples of how just making one small change to your kitchen can make a huge difference!!
Oh how true this is for me right now. Oh how true. Luckily I’m here :-). By the way, I can’t handle your kitchen, it’s too perfect. I’ve never seen anything like it and it’s the best thing I’ve ever seen. I’m doing a modern eclectic boho kitchen, predominately white, some wood accents, maybe darker lower cabinets, maybe gold hardware (that’s where I’m stuck), and then pops of beautiful colour like you have here. I’m excited!
Sandra, I’m so glad that I came across your blog! You’ve given so much great information that I can use every day in my job doing kitchen cabinet sales. And then there’s the whole DIY part for me personally! I’m really hoping that you can answer my question, though. I have a customer who is refacing her cabinets. She has frameless cabinets and used to have exposed hinges. She wanted concealed hinges so we had the hinge holes drilled 1″ (center) from the edge. She has her new doors but when she hangs them, there’s a 1/4″ gap between the door and center stile, even after adjusting them. We were using full overlay hinges. Can you advise which type of overlay hinge to use and how to rectify the gap? Thanks so much!
While it is important to stay true to your personal style, you don’t want a lantern that is half the height of your door or an oversized mailbox beside a tiny cottage. So, take into account what you are working with as you choose the style that is most you! “I suggest they get painter’s tape and put it on the house in the dimensions of the fixture to get a sense of the size. You want it to be the correct proportion,” says Brandino Brass team member Megan Brasher, adding, “To get the feel for how it will affect your home’s curb appeal, not only do you need to look at it right next to the front door, but you also need to take a step back and get a view from the street.”
I can totally appreciate that. You’ll notice that these cabinets are also flush with the cabinet frames, which makes the hinges a little less noticeable. But sometimes, the hinge effect just isn’t quite as charming, and can be more distracting than anything. A lot depends on what kind of cabinet overlay you’re dealing with and the aesthetic that you’re looking for in this sort of project.
Due to its quasi-metallic makeup, crystal does much more than just sparkle — it also exhibits other coveted traits. When rubbed to the point of vibrating, crystal will produce a musical tone. It is also stronger than glass and can be blown quite thin. Cliffside Industries distributes German crystal, which is stupendous in its clarity and diamond-like cuts, as well as products from the world-famous Austrian crystal maker Swarovski AG.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
Shaker style cabinets. The most common style of cabinet offers flexibility in design, and they work well with knobs or cup or bin pulls. Shakers are known for their simplicity and clean lines, so simple hardware is often used, such as round knobs.Traditional nickel or steel knobs or pulls are common, as well as vintage glass or ceramic knobs. Vintage pulls with exposed screws provide a classic touch or industrial feel to a new kitchen with shaker cabinets. Tubular bar pulls — which can be short or long and dramatic — modernize a traditional kitchen with shaker cabinets. Flat bar pulls offer a contemporary edge, while wire pulls keep your décor traditional. Arched and footed bar pulls offer a classic look on shaker style cabinets.
Cabinet hardware sizes can vary depending on your own personal design preferences, but you’ll want to choose a size that is both stylish and functional. Bar pull sizes are generally determined by the “center-to-center” measurement (the distance between the two screw holes). If you have pre-drilled cabinetry, you’ll need to buy hardware that fits the existing center-to-center measurement. Otherwise, you’re left to your own devices in choosing the size of your cabinet hardware. Here are a few general guidelines to follow:
Once you’ve selected your new handles and pulls, it’s time to remove all the old ones. Using a drill or screwdriver, slowly back the screws out, then gently pull the old hardware away from the door or drawer front, so as not to damage the finish. Keep the old screws and pulls/knobs together in a plastic baggy so it’s easy to donate or toss them depending on their condition. If you’re going to repaint your cabinet doors, do it now.
Once you have decided on a style and shape for your hardware, you still need to choose the finish for your knobs and pulls. A shiny chrome finish has a modern feel, while brushed nickel or pewter may bring a more traditional look to your kitchen. Black hardware can be modern in a glossy finish or traditional with a matte finish. Many hardware lines come in several different finishes to help you find exactly the look you want.
Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!
If you think about it, you open your cabinet doors multiple times a day. Over a few years, that can take a toll on those hinges holding your doors in place. Replacing them with hinges that are made from a quality material like solid brass will not only help your cabinet doors function better, but it will make them look better, too! Choose a hinge color that matches the other hardware in your kitchen for a unified look and feel. For easy installation, look for hinges that are adjustable so you can use the same hinges to fit multiple sized doors and cabinets. This small change will make your cabinets look updated and keep them functioning properly for years to come.
Want sleek form? Want functionality at its finest? Say hello to handles. Handles for white cabinets allow a firm and full grip to easily pull open or push close any cabinet door. Handles come in a cornucopia of shapes and sizes to male for a match with your kitchen style. Handles offer installation flexibility, with vertical and horizontal options, which allows for additional detailing for your white cabinets.
1. Stick with the theme. The hardware you choose speaks to your theme in the same way your kitchen cabinets do. Which hardware works best with different themes? Sleek, tubular pulls, like those in our Torino collection, complement the streamlined look in modern and contemporary kitchens. Traditional cabinets tend to have more detail and benefit from simple, smooth knobs, like the Projectionin style from our Drake collection. French country can benefit from hardware with an antique look, like our Windermere collection that comes in gun metal, rubbed bronze and brush pewter.
The quick answer is yes, you can change the hinges. The hard part is what type. Cabinet doors have lots of different configurations.....full overlay, partial overlay, inset, etc., etc. The hinges have to fit the door style. There are hidden hinges that screw to the cabinet framework without major holes, and there are European type hinges that require a large hole to set the hinge into. Go to big box and look at the hinges, what is available can be mind boggling, until you understand the type of door you have.
I love to see your work in progress! And I agree that the wood valance over the window looks so much better painted white, you almost don’t see it now. Funny story, I had a similar valance in my last house and as part of my kitchen refresh, I had the contractor knock that out and oh what a difference it made! I had only 1 tiny window in the kitchen and that stinking valance blocked so much light. Your home is much more open and bright with all the white now, thanks for sharing! You’re in the home stretch now!!