In contrast to knobs, which have only one screw attachment, a cabinet pull (or cabinet handle) is attached to the cabinet door or drawer front with two or more screws. Because there are multiple screw holes, one of the most determinative factors in choosing handles is the center-to-center measurement; i.e., the difference from the center of one screw hole to the center of the next.  
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
Sometimes brass finishes can be difficult to match since there are so many types (unlacquered, satin, antique, polished, etc.). Generally, you just have to order samples to see everything together. However, I will say that you should stay away from polished brass - it gives a very 80s vibe! Unlacquered brass starts shiny, but has a richer tone that gives a beautiful patina over time. For a more modern brass look, stick with the satin finishes!
Between your cabinets and your drawers, you may have thirty of more cabinet handles in your kitchen, which has a significant effect on the look of the room, so you will want to choose knobs and pulls that match or complement your kitchen decor. If your kitchen has a modern look, consider choosing a cabinet handle that has angles and a very simple design or a square knob. Keep in mind that you can find knobs and pulls in a number of different designs, so if you have a Tuscan-themed kitchen, you can find kitchen cabinet knobs stamped with grapes, and if you have a rustic kitchen, you can find kitchen cabinet handles made from twisted wrought iron.

For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.


Shake a can of rust-inhibiting metal spray primer for the amount of time recommended by the manufacturer. Position the can the recommended distance away from the hinges -- it varies among manufacturers. Spray a light coat of primer on the hinges and screw heads using steady, even sweeps. Make sure you spray the sides and edges. Shake the can frequently while you spray. Allow the primer to dry for the amount of time recommended by the manufacturer. Apply a second coat of primer and allow it to dry completely.
Knobs, which are attached with a single screw, are most frequently used on cabinets, and are available with a built-in screw, known as a one-piece knob, or with a separate top and fastener, known as a two-piece design. Modern drawer knobs are made in a variety of materials including brass, zinc, stainless steel (sometimes found in kitchens), bronze, glass, crystal, plastic, wood, and other natural and man-made materials. 
Rest easy, friends, you can do this, too.  And then, since it looks much better and you are thrilled and at peace with it, you can move on to dreaming about that full kitchen reno you are still working towards… one day.  Or, maybe you will be so happy with the small changes you made that you can cross that idea right off the list and move on to dreaming about making other areas of your home just right.

It may take some time for you to consider what effect you would like to create with your hardware on your kitchen cabinets. In fact, some styles, patterns, and finishes are so beautiful or unique, that they become the focal point in the kitchen and a topic of conversation. Many of the ceramic and glass styles are so cleverly finished that they look too pretty to simply be part of a kitchen cabinet.

Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening. 
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
You don’t need to match your cabinet hardware finish to the rest of your kitchen. This is one area you can add a little bling. For example, we always recommend chrome faucets because chrome is the most durable (and in our experience, although popular, brushed nickel looks dingy and fingerprints are hard to remove), but consider brushed nickel or champagne gold for your cabinet hardware for a nice juxtaposition of metals in your kitchen
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
“We find it refreshing for people to purchase what they like and what feels good to them, not caring what the ‘Joneses’ have,” says Renee. The Brandino Brass team regularly works with professionals who have their own signature styles. “One architect in town may use the same small knob all over the house all in the same finish for continuity. Another one will use different styles and finishes in each individual room,” says Jessie Isom, Brandino Brass team member. “There is no right or wrong if you like it.”
Also, experiment with different shapes. Things like knobs, handles, toilet paper holders, towel racks and hinges have a lot of expressive power. Beyond color, though, you should take advantage of their different shapes to accentuate certain features in a room. Pay attention to details like the width of drawers and the height of cabinet doors, and experiment with different shapes to complement them.
Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening. 
If you have a removable island or a butcher block in your kitchen, an easy way to make that extra piece look cohesive with the rest of your kitchen décor is by adding coordinating cup and cabinet pulls to drawers and doors. This addition will make your island look purposeful and blend it with the rest of your kitchen cabinets — even if the finish or countertop is different.
Swapping these items out is often easy, and Los Angeles-based designer Betsy Burnham says her clients are frequently surprised at the visual impact of something as simple as carefully chosen hardware. Last summer, she added door pulls made of rope tied in small nautical knots to the built-in cabinets at a California beach house, inexpensively adding a dash of personality to the space.

Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!
×