Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less.   The most common pull sizes for standard cabinetry are 3”,  4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches.  Standard knob sizes are less than 1.5 inches in diameter.
Hanging knobs on a flat-front cabinet is pretty straightforward: You’ll want to position the knob in the bottom corner (for upper cabinets) or top corner (for lower cabinets) of the door. Knobs should be placed equidistant from both sides of the cabinet. A guide like this one can help you to get the measurements right. The exact distance will depend on the look you want and the size of your knobs: Test one or two before you drill a whole kitchen’s worth of holes.
2. Keep finishes cohesive. You’ll find hardware in a range of finishes from brushed nickel to brass. While mixing and matching the hardware around your kitchen is fine, you should try to maintain the same finish and keep colors as close as possible. Sometimes you’re forced to buy hardware from more than one retailer, but when doing so make sure you keep finishes cohesive.
If you don’t want to match to your faucet, then think about some of the other components in your kitchen. For example, if you have a black stone countertop, then antiqued metal or even satin black knobs could help tie the room together. Alternatively, base your color and finish choice on the cabinets themselves: Dark hardware to match dark wood or light hardware as a contrast. Choose more rustic finishes like antiqued or hammered metal to go with traditional cabinetry or go with sleek brushed metal for a more modern look.
SimplyBeautifulKitchens.com is a participant in the Amazon Services LLC Associates Program and other affiliate programs, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com and other merchants websites. You should always perform due diligence before buying goods or services online. The Owner does not accept payment or merchandise from manufacturers in exchange for writing reviews.

A common choice is to use knobs for all drawers and pulls for all doors (or vice versa). The problem with knobs is they are harder to grip and fingernails tend to mar the cabinet door. It is much more comfortable to open a drawer using a pull, which allows the whole hand to grab instead of only your fingertips. We generally use pulls (no nobs whatsoever) in our kitchen designs.  
Your kitchen is coming along really well, and all that lovely light will be an absolute joy! Sadly, I have just a word of warning about the handles though. We had these in our kitchen, and they proved quite annoying. They’d catch on your clothing, especially blouses/shirts. That end of the front of button-through blouses, where the seam folds back would always get hooked onto the end of the handles! And pockets, too would get caught. This invariably ended up with torn clothing, as you continued to move away, not realising you’d been ‘caught’. We also live near the sea, and ours rusted over a few years, although that may be just an inferior brand. I lived with ours for about 4 years, then changed them all. We had them in our bathrooms, too, and they’ve all been changed as they were such a pain! I can see you love them, so don’t want to burst your bubble, but just thought I’d let you know. :(
Robyn and Sam’s home in Toronto is an all-white, minimal lover’s dream. Intentionally kept simple and streamlined, it has just the essentials. Their kitchen is a great example of a minimal and modern space done right. It’s also a great blank canvas to play with to show you more examples of how just making one small change to your kitchen can make a huge difference!!
The color white, and more specifically, white colored cabinets, have never been more popular in today’s kitchens. White is always in style, regardless if you have a slick modern kitchen or relaxed country style. With their relaxed style and design flexibility, it’s no secret as to why white cabinets are a constant crowd pleaser. The color white can make a room look larger and timeless in one broad stroke. With white cabinets, hardware is the most crucial detail, as it is more than just an accent, Hardware completes the room and adds overall value to your kitchen. With all of the available options, selecting the perfect hardware for your white cabinets can be a frustrating exercise. Below we discuss what to consider when selecting hardware for white kitchen cabinets.

Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
As latches like these are elements that people come into contact with every day — literally gripping them for support or activating them with a gentle nudge — architects should keep both aesthetics and functionality in mind when specifying these seemingly simple components. To help you as you search for kitchen hardware on Source, here are a few savvy choices that fit well with modern clean spaces; ones that, even when situated in repetitive rows, won’t take attention away from sleek cabinetry design:
Ultimately, you should choose your hardware according to your personal preferences, kitchen style and goals for functionality. If you’re concerned about resale value, recognize that the most popular hardware finishes are satin, nickel and bronze. There are no hard-set rules to follow when it comes to adding the final details to your kitchen, and many people choose a combination of knobs and pulls. If you’re unsure of which to choose for your kitchen cabinets or drawers, it’s wise to examine the pros and cons of both.
Also, experiment with different shapes. Things like knobs, handles, toilet paper holders, towel racks and hinges have a lot of expressive power. Beyond color, though, you should take advantage of their different shapes to accentuate certain features in a room. Pay attention to details like the width of drawers and the height of cabinet doors, and experiment with different shapes to complement them.
By adding hardware you like, you’re literally installing your style into the room — and this will make any accessories you want to add in feel like a part of the kitchen’s design, and not out of place. Of course, not every cabinet + hardware combo is going to work, but see how far you can take it when it comes to choosing hardware outside the traditional style of the cabinets.

​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.


The homeowner has already installed a new tile backsplash, and will also be replacing the floors with new tile and painting the walls once I’m finished with the cabinets.  But the homeowner was concerned about the hinges standing out against a light cabinet color.  A cabinet refresh is going to help tie the updates together, and when we got to talking about the hinges, I did some research, and found a great local woodworker to help change the hinges from exposed to concealed.
SimplyBeautifulKitchens.com is a participant in the Amazon Services LLC Associates Program and other affiliate programs, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com and other merchants websites. You should always perform due diligence before buying goods or services online. The Owner does not accept payment or merchandise from manufacturers in exchange for writing reviews.
Painting cabinets yourself is cost-effective -- a few gallons of paint, sandpaper, cleaner -- but the process is time-intensive. You can paint most cabinet surfaces, but proper prep is key to success. For laminate and melamine finishes, be sure to rough up the surface with 150-grit sandpaper, and apply a good bonding primer before topping it off with the color of your choice.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.
At this point, you will have narrowed down your hardware choices to a specific style, type, size and finish. Next thing to incorporate is your budget. A good starting point is to count how many knobs and pulls you will need for your cabinetry and determine a price range that is comfortable for you. Many hardware manufacturers have multiple lines of varying quality and price, so be sure to find a manufacturer that uses high-quality materials. Buying cheap can seem like a good idea in the short run, but cheaper metals will degrade faster down the road and face a much higher risk of breaking or bending. Stainless steel hardware, for example, should be solid (not hollow) with a durable but even finish.
2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
I thought for sure I’d go with the modern beauty on the upper right (the It Pull), but when I held them both up to the cabinets they whispered to me “go for the Bronte.” Like Shakira’s hips, cabinets don’t lie, so I went with the Bronte. Then we needed to chose the finish. As much as I lurrrrrrve gold hardware, my husband nixed that idea because he does not understand this is not the gold of the 1980’s. 😉 Since he gets very little choice in the rest of the house, I took one for the team (not really, I actually love the dark finish too) and chose the lovely Venetian Bronze finish. While gold would certainly have elevated this kitchen to on-trend status, I went for what works best for our marital harmony.
Hello Mr. TretheweyMy name is terry cotto, when we built our beautiful home 16 years ago, in Sierra Madre Ca I had my claw tub installed,( my child hood remembrance) It appears, that the claw legs of the tub were not installed properly, and one leg fell off , tub was slightly tipping to the right. I had a handyman come over and reinstall the claw legs, tighten so this would not happen again. The other day, while I was bathing I noticed the seal of the drain on the outside rubber was not laying properly, plus it was leaking, ( I think this was due to the leg falling off and unbalancing the ring. Well, now I really don't know what to do about that. I believe the thing to do is remove the cover off the top drain , ok, but than what do I have to move the claw tub, impossible. How do I replace the rubber of the outside of the top drain pipe, it appears to be brittle. (Not good)Please answer my questions, and I will hire the handy man again to help me. Thank you. I have learned so much from T.O.H weekly shows, I am a loyal fan at 75. I tell my 80 year old husband, you need to watch these shows with me, and we can do it ourselves, the right way. God Bless you all for the great job your doing, I need to know how to do it right, so it doesn't happen again. a picture would be good, I can see exactly how its done?
When you’re choosing cabinet hardware, think about the number of times you’ll touch these pieces every day. If your cabinet pulls look and feel good and function well, you’re sure to derive pleasure from them. Browse our narrowed-down choices, from modern cabinet pulls to traditional knobs. Simply replacing your cabinet knobs is the easiest (and cheapest) way to spiff up a kitchen. Get started here.
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
When I’m talking about metals, I consider the silver metals as one grouping. So, when you have stainless appliances (silver), a chrome faucet (silver) and brushed nickel lighting (silver) those all count as one metal in my book- SILVER. I personally think Nickel is the most timeless of the metals. Brass has really gained in popularity with interior designers, but is probably a trendier choice. I’ve seen a rise in the popularity of black hardware especially in this age of farmhouse- EVERYTHING (Thanks Chip and Joanna). I think every room in your house should have a little black in it, so if you can bring in the black with your second metal in your kitchen, DO IT!!
×