Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.
Most knobs and pulls are only a few dollars apiece but when you consider the sheer number that you’ll need, those costs add up fast. For each standard lower cabinet with two doors and one drawer, you’ll need three pieces of hardware — and two more knobs or pulls for the matching upper cabinet doors. With that in mind, here are a couple of factors to consider:
Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
One of the biggest enemies of a clean kitchen lies in careless cabinet hardware selection. Apart from choosing a gaudy color or ill-fitting shape, the one detail that can make or break the look of a cabinet door actually is the humble piece of hardware that is chosen to open and close it. From round knobs to long pulls and magnetic mechanisms, there’s a world of choices to make when it comes to honing in on the perfect hardware for kitchen cabinets. Some can stick out like a sore thumb, while others can be completely invisible.
Consult with a contractor or a knowledgeable salesperson about which hinges will work with your doors. If your doors are flush with the cabinets, butt hinges can be used. They are lower in price than others but do not self-close. European hinges are installed on full overlay, frameless or inset doors. They are widely used because of their ease of installation and ability to be adjusted once in place. These hinges self-close. Partial wraparound hardware will support larger doors, but it does not self-close. Several other types hinges are available. The construction of your door, ease of installation and price will need to be considered. .
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!
We also did that. Our handles are those stainless steel round bars. Loved the look with our white slab door/drawer fronts! Turned out there was big problem with sides of the horizontal drawer pulls snagging pants pockets. So, replaced those with centered flush type steel rectangular pulls that we mounted on the drawers after using router to make mortise holes No more snagging pockets!
I had already chosen polished nickel hardware (which I will share more about soon), so my hinges needed to coordinate. I decided to use Rub n Buff to give them a much-needed update. If you don’t know, Rub n Buff is a fantastic metallic paste used to give almost anything a metal finish. I chose it because it is so easy to use and gives a lasting finish.
Nickel and chrome have about the same level of durability, but chrome is sometimes a bit more expensive. Brushed or matte finishes hide fingerprints and watermarks better than shiny finishes. You’ll generally find a lot more hardware options in brushed nickel than in chrome or stainless steel. Poor quality nickel and chrome finishes can peel and flake over time. Stainless steel, which is usually matte, is the most durable of the silver finishes and as such, is usually the most expensive. True stainless steel hardware is typically made from a full thickness metal alloy and it’s not just plated on the surface like nickel and chrome are.