Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.


Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.
Prior to making the purchase of your new cabinet hardware, take some careful measurements of the existing hardware. Write down sizes, as well as the spacing of the screws. This should eliminate the need to drill new holes. Accurate measurements are essential to avoid additional work or the need to return and exchange your hardware purchase. In fact, it is a good idea to bring some of your old hardware with you for size comparison purposes, unless you are shopping online for your hardware. In that case, simply have the hardware next to you.

Good morning and happy Monday, lovely people! I hope y’all had a wonderful Thanksgiving week. Ours was a little on the insane side, but it ended perfectly. We moved to our new house {Memaw’s house} a little over a week ago. It was crazy getting settled just in time to host our family’s Thanksgiving dinner. It was hard without Memaw. Tears came easily and our family time was just really sweet. I’m very thankful.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
The homeowner has already installed a new tile backsplash, and will also be replacing the floors with new tile and painting the walls once I’m finished with the cabinets.  But the homeowner was concerned about the hinges standing out against a light cabinet color.  A cabinet refresh is going to help tie the updates together, and when we got to talking about the hinges, I did some research, and found a great local woodworker to help change the hinges from exposed to concealed.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
Standard hardware is a breeze to install. All you need is a Phillips-Head screwdriver. Simply replace standard screws into the pre-cut holes.If the holes are pre-drilled on your cabinet drawers and you now want to place a single hole, measure the distance between the two holes and center. If your cabinet doesn’t currently have holes or hardware, knowing where to place the different size knobs on each cabinet can be tricky. If there are no holes, and you’re on your own when drilling into the corner of the cabinet door give yourself 2 1/2 to 3″ of space in the corner before you drill in a hole.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.

A common choice is to use knobs for all drawers and pulls for all doors (or vice versa). The problem with knobs is they are harder to grip and fingernails tend to mar the cabinet door. It is much more comfortable to open a drawer using a pull, which allows the whole hand to grab instead of only your fingertips. We generally use pulls (no nobs whatsoever) in our kitchen designs.  
Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
Before you get to hardware, it’s crucial to select your cabinet doors. The type of door you select will influence the style tremendously. The most popular styles of cabinet doors at the moment are Shaker, traditional, and modern. A Shaker-style cabinet front is a utilitarian design, with four rails and one middle, slightly recessed, center panel. It’s clean and simple design that can work well with most kitchen styles.
×