I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
There are a couple of ways to go about choosing the right color and finish. One school of thought advises you to choose based on the color and finish of the kitchen’s faucet. Given that most faucets are either silver or brass in color, this advice can be limiting, especially if you have your eye on stone knobs or another finish that is not common in faucet design.
These small items — doorknobs, drawer pulls, cabinet-door handles — are "the jewelry" that can add style and sparkle to any space, says New York-based interior designer Young Huh. Just as the right necklace can turn a simple dress into a fashion statement, a striking new set of knobs on an old cabinet, or vintage crystal doorknobs can bring a huge dose of style to your home with minimal expense, she says.
If you want to use warm metal like matte brass or gold or copper in your house, but are hesitant because you’re afraid it might go out of style in the next few years, adding warm metal cabinet hardware is a great way to go. If brass, gold and copper do go out of style in the next few years, most cabinet hardware is pretty simple to replace all by yourself. If, however, you decide on a warm metal faucets, door hinges or lighting fixtures, many of us would have to hire a professional or handyman to replace those items. But cabinet hardware can easily be switch out by almost anyone. Just make sure you use standard sized hardware.
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
Ceramic knobs bring such charm to your kitchen. They’re reminiscent of a sweet country cottage, or an old world farm house. It’s not hard to imagine the scent of a freshly baked pie or loaf of bread cooling in the window. Ceramic knobs pair quite nicely with natural wood finishes and glass hutch cabinets. Wether you choose plain white or a funky pattern, ceramic knobs give your kitchen a homey flair.
Before you get to hardware, it’s crucial to select your cabinet doors. The type of door you select will influence the style tremendously. The most popular styles of cabinet doors at the moment are Shaker, traditional, and modern. A Shaker-style cabinet front is a utilitarian design, with four rails and one middle, slightly recessed, center panel. It’s clean and simple design that can work well with most kitchen styles.
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
If you’re looking for a style that’s hot right now, look no further than modern cabinet hardware. This look features sleek, straight handles in horizontal lines, usually in a stainless steel or chrome finish. The hardware is skinny and will likely stand out against the color of your cabinetry. Another option is a rounded, long and vertical handle in the same finish.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
I watch you every Sunday morning. I used to help run a construction co. here in Knoxville,TN. I am now my Moms cargiver(87). I lost my dear sweet husband last November. I am trying to sale my house. I am just stressed trying to find replacement wrap-around hinges and pulls for my kitchen and bath. I also am going to replace my laminate tops. Do you have any sources I should check. You two remind me of my sweet dad and me from years ago. Please HELP!!!!!!
That being said, buying every make and model turned out to be a good idea. I was pretty pumped when I installed my first door…until I shut the door and there was a gap the size of Kansas where the door didn’t cover my opening. I should have taken a picture because it was pretty hilarious-looking. Wrong hinge. So I removed the 1 1/4″ overlay hinge, installed the 1/2″ overlay and was good to go. The holes that need to be drilled in the door will be the same in size, depth and location regardless of your overlay measurement.
Budget is, of course, a key factor in any part of your kitchen remodeling decisions. While you’ll want to pay as little as possible right now, remember that quality matters in the long run. Your local kitchen cabinet showrooms will offer you the largest variety, with people who can help you choose high-quality hardware within your budget. Remember that the price is based on the finish, as well as the design and size. Knobs are less expensive than pulls.
What kind of new hardware should you install in your updated kitchen? There are so many choices out there it can be overwhelming. Knobs or Pulls? Nickel or Brass? Will you be able to see the holes from the old hardware? Because I am being asked these questions on a daily basis I’ve put together a general guide to updating hardware and have included some of my favorites to share with you.