Knobs, which are attached with a single screw, are most frequently used on cabinets, and are available with a built-in screw, known as a one-piece knob, or with a separate top and fastener, known as a two-piece design. Modern drawer knobs are made in a variety of materials including brass, zinc, stainless steel (sometimes found in kitchens), bronze, glass, crystal, plastic, wood, and other natural and man-made materials. 
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.

What they are: Sturdy yet glamorous pulls that complement many styles of cabinetry. Here linear flat bar pulls not only underscore the contemporary feel of the kitchen, but oversize pulls eliminate the need for two pulls on a wide drawer. A good rule of thumb is to use two knobs or pulls on drawers 18 inches wide or wider. But if you choose superwide pulls like these, one is enough.


DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright© 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
We also did that. Our handles are those stainless steel round bars. Loved the look with our white slab door/drawer fronts! Turned out there was big problem with sides of the horizontal drawer pulls snagging pants pockets. So, replaced those with centered flush type steel rectangular pulls that we mounted on the drawers after using router to make mortise holes No more snagging pockets!
Flat-panel cabinets.Most often seen in modern or contemporary kitchens, flat-panel cabinets embrace minimal embellishment to focus on natural materials. Subtle hardware choices are best, such as stainless steel bar pulls. You often see long, extended versions placed on the door or drawer.If you prefer square edges, you can choose a flat bar pull. Recessed pulls offer a functional option that work especially well for high-traffic kitchens. If you’re aiming for a minimalist look to your kitchen, you might consider discreet tab pulls for your flat-style cabinets.

Concealed hinges can go in face-frame or frameless cabinets and on any door type—including full overlay, partial overlay, or inset—as long as the doors are at least ½ inch thick. The hinges I'm using are for frameless cabinets with inset doors. To find the hinge that will work with your door type, consult the hinge company's online brochures and customer service line. Then, with the right hinges in hand, follow the steps on the next page to install them.


And starting to play with my new HVLP turbine spray system.  (Whenever I say HVLP turbine, I think of the movie “A Christmas Story” and how Ralphie describes his Red Ryder BB gun – “an official Red Ryder, carbine action, two-hundred shot range model air rifle.”  I think I’m equally enamored with my new gun, even if it doesn’t have a compass and a stock. 😉
It’s easy to get caught up in selecting the larger items, such as cabinetry, countertops or flooring for your new kitchen when building a custom home or renovating your existing home. "A project isn't complete until you've selected the right hardware that strikes a personal balance between form and function. These final touches will pull the whole project together and are fantastic for imbuing it with a flair that reflects your personality," says Jonathan Pilley, Co-Owner at Push Pull Decorative Hardware in North Bethesda, Maryland. Decorative hardware comes in a variety of types, sizes, styles, materials and finishes. So, what should you pick? Read our 5 tips on choosing the right kitchen cabinet hardware.
Wow! I finally figured out what to ask for, THANKS. Old hickory cabinets still look great, and the wife loves them, but hates the sound of them closing. Want soft closing hinges, a nice project. They are face-frame cabinets, with semi-inset doors with about 1/4″ overlay.and inset about 3/8″. What hinges do I need? Plan on doing this just as soon as the soft closing drawer slides are all installed.

​If you want to use warm metal like matte brass or gold or copper in your house, but are hesitant because you’re afraid it might go out of style in the next few years, adding warm metal cabinet hardware is a great way to go.  If brass, gold and copper do go out of style in the next few years, most cabinet hardware is pretty simple to replace all by yourself.  If, however,  you decide on a warm metal faucets, door hinges or lighting fixtures,  many of us would have to hire a professional or handyman to replace those items.  But cabinet hardware can easily be switch out by almost anyone.  Just make sure you use standard sized hardware.
The size of your cabinets will influence the size of your knobs. If your cabinets are smaller in scale you’ll want to opt for hardware that is likewise, such as minimal-scale circular knobs. Longer hardware is necessary when you have extra long cabinet doors—or can be used if you want to make a more of dramatic statement. Most cabinet doors are 24”, so you want a knob about 2”-3” size knob. For a larger cabinet door you can size up to 3½” or 4”. For a cabinet door under 20”, source hardware that’s closer to 1” to 2” size in diameter or length.
Shaker cabinets offer a simple and traditional design. Versatility is a large part of what makes them so timeless. Ultimately, you achieve the vibe you’re going for through the finishing touches, one of those being the hardware you choose. We’ve selected some of the top hardware styles for shaker cabinets, and what looks they will bring to your kitchen.
Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.

Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening. 

Remodeling and customizing your kitchen can be a big project. After planning and designing on the large scale it might be tempting to coast through choosing the cabinet hardware, but high-traffic rooms such as kitchens deserve detailed attention. Choosing the right hardware size requires a balance of style and function. Sacrifice one for the other, and you probably won’t be happy. You’ll be frustrated every time you try to pull open a drawer, or you’ll be disappointed every time you walk into the room.

There is a lot of misunderstanding when it comes to crystal. Upon first glance, it looks like glass, but it is in fact of higher quality and clarity, and its chemical composition is markedly different. Contrary to what its name suggests, crystal is not crystalline on a molecular level — that is, its molecules are not arranged in a rigid, repeating structure.
Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.

Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!

Cabinet hardware sizes can vary depending on your own personal design preferences, but you’ll want to choose a size that is both stylish and functional. Bar pull sizes are generally determined by the “center-to-center” measurement (the distance between the two screw holes). If you have pre-drilled cabinetry, you’ll need to buy hardware that fits the existing center-to-center measurement. Otherwise, you’re left to your own devices in choosing the size of your cabinet hardware. Here are a few general guidelines to follow:
I love to see your work in progress! And I agree that the wood valance over the window looks so much better painted white, you almost don’t see it now. Funny story, I had a similar valance in my last house and as part of my kitchen refresh, I had the contractor knock that out and oh what a difference it made! I had only 1 tiny window in the kitchen and that stinking valance blocked so much light. Your home is much more open and bright with all the white now, thanks for sharing! You’re in the home stretch now!!
Hidden hinges also come in a soft-close style if you’re one of those people who want the latest and greatest. (Is it really that bad to hear a door close?) My new cabinets came with soft close hinges that I personally could take or leave.  I still find myself trying to shut them all the way instead of letting them do their thing. You might not want soft-close hinges if you’re the type who likes to slam things when irritated. (Just a thought.)
At a home renovation in Connecticut, cabinet fabricator Michael Madore experimented with what he calls an "aggressive" metal-sanding process to pull out the grain from the whitewashed oak plywood. For the hardware-free cabinets, Julie Salles Schaffer looked to a drawer pull detail derived from Giò Ponti’s work—though she admits the radial edging is an effect entirely her own.
I am taking on more and more cabinet refresh projects (for hire), and still never tire of the transformations.  My latest project is an oak, galley style kitchen, and I’m digging deeper into ideas to make these older kitchens look more modern.  Paint is obviously a big hitter in terms of updating a kitchen, but let’s talk about something else that is equally powerful – cabinet hinges.
I would like to use a hinge similar to the wrap around no mortise Amaroc 3175s but am disappointed to learn the poor reviews ….sloppy….bent…flimsy…not worth it…low qc import. Perhaps they were better in the past! I would be most greatful if you could recommend a better quality hinge of that style. Alternatively,Can the full inset euro cup hinge be adapted to a face frame cabinet by building out the inside lip ^
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.
A good price for pulls begins at around $12.00 a piece because anything less looks cheap and the quality will be sub-par. Look for cabinet hardware at plumbing or cabinet showrooms. They will have a larger variety and better quality. Look through the displays or catalogs and order several samples in different styles and finishes to compare to the rest of the finishes in your kitchen.
3. Know when to use knobs over pulls. In traditional and country kitchens, putting a knob on a cabinet is not uncommon. In fact, with many cabinets, knobs may a better option than pulls. How do you know the difference? When kitchen cabinets are ornate or finely detailed, go with a knob rather than a pull. A knob is smaller and simpler and doesn’t take attention away from the design of the cabinets.
From round and oval to square and rectangle, cabinet knobs come in all types of shapes and sizes. Show off your personal flair for design with novelty cabinet knobs. If you’re going for a coastal look, we have novelty cabinet knobs shaped like sea shells, starfish and sea horses. If you have a child who plays sports, we’ve got you covered with soccer, baseball and basketball shaped cabinet knobs. We also carry antique cabinet knobs for history lovers.
Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!
×