There are a few options for hanging drawer hardware. Usually drawer pulls (or knobs or cup pulls) are centered on the face of the drawer. In a more modern kitchen, you may choose to hang them closer to the top of the face. For Shaker-style drawers, you can hang knobs or pulls either in the center of the drawer OR centered on the top stile. Which look should you go with? Whatever you like the best in your kitchen. Just make sure that you’re consistent across all the drawers. Drawers longer than two feet may look better with two knobs or pulls.
Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!

The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Pulling design from old pharmacies and soda fountains, latch hardware is that without a doubt a nostalgic throwback. Maybe not the most functional if you’re in a hurry, but handy if you’re looking for a little extra security from pets or children. Latches are another hardware type that can easily be mixed and matched, so maybe just keep them to the lesser used cabinets.

If you don’t want to match to your faucet, then think about some of the other components in your kitchen. For example, if you have a black stone countertop, then antiqued metal or even satin black knobs could help tie the room together. Alternatively, base your color and finish choice on the cabinets themselves: Dark hardware to match dark wood or light hardware as a contrast. Choose more rustic finishes like antiqued or hammered metal to go with traditional cabinetry or go with sleek brushed metal for a more modern look.
Recessed Pulls mimic the utilitarian style of traditional office cabinetry. They’re built into the cabinet door and can be crafted from the same material to blend in or a contrasting material to highlight their presence. They’re also great for high-traffic kitchens because they don’t protrude from the doors, meaning there is little risk of them snagging on clothing.
Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening. 
Hidden hinges also come in a soft-close style if you’re one of those people who want the latest and greatest. (Is it really that bad to hear a door close?) My new cabinets came with soft close hinges that I personally could take or leave.  I still find myself trying to shut them all the way instead of letting them do their thing. You might not want soft-close hinges if you’re the type who likes to slam things when irritated. (Just a thought.)

Consider the style that you have used to decorate your home. Traditional styling indicates a need to use cabinet hardware that has a brushed finish. Pewter, nickel, and polished brass blend well with traditional styling, although other styles will look nice as well. Perhaps you would prefer to contrast the traditional cabinets with some hardware that leans more toward the unique and modern.
After the center panels have been removed, take measurements of the inside openings. I subtracted an 1/8” from the length and width just to make sure the glass would fit. Now, go to Lowes, find the glass cutting isle and give the kind man or woman working there your list of measurements. Make sure you have other things to shop for because this is going to take a while, but it’s super duper cheap so it’s worth the wait. By the way, you don’t have to use glass, you could use that cool radiator metal, chicken wire, punched tin, you name it, sky’s the limit!
It’s definitely possible to change out the hinges without redoing the cabinets – you would just have to make sure that the holes on the frames where the old hinges were, are able to be filled and touched up so that they’re not obvious. I’m not sure of the cost, but hinges aren’t cheap, and I definitely recommend using a carpenter to do the work. Hinges can be maddening!
Knob or pull? Bronze or silver? Small or big? Kitchen cabinet hardware is more than just a pretty decoration; knobs and pulls keep your cabinet cleaner and protect the finish. Plus, while they’re little, they can actually make a big impact on your kitchen’s appearance. But with thousands of options out there, how can you select the right hardware to make the best impact? Take these things into consideration before you make your final kitchen cabinet hardware selection.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.

Once you’ve selected your new handles and pulls, it’s time to remove all the old ones. Using a drill or screwdriver, slowly back the screws out, then gently pull the old hardware away from the door or drawer front, so as not to damage the finish. Keep the old screws and pulls/knobs together in a plastic baggy so it’s easy to donate or toss them depending on their condition. If you’re going to repaint your cabinet doors, do it now.
If you’re going for wood paneling, the process is pretty simple. Fasten the pieces together and cut to the size of your appliance. Then, remove the handles from your appliance and glue the panels onto the front using a hot glue gun. You can either paint the wood and the sides of your appliance to match your cabinets, or you can leave it as is for a natural unfinished feel. Complete the look by adding new appliance pulls to match the rest of your kitchen hardware. Appliance covers can be added to just about any kitchen appliance that has a door like a refrigerator and dishwasher.
Accessorizing is the most important part of any outfit. A little glimmer, a little glam or maybe something unexpected and modern can make an ensemble. Well, I think that accessorizing happens to be just as important when decorating your home, which is why we’re exploring the “jewelry options” for the kitchen: hardware! Often overlooked, but capable of extreme 'wow' factor, the pulls on our cupboards can easily be swapped out to drastically change the style of your space.
×