The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
My go-to shop for all of my hardware needs is D.Lawless Hardware – I’ve been using hardware from there for a while now and it’s always the best quality at the lowest prices. They sell so many other awesome products too. Everything from knobs and pulls, drawer slides and systems, to wood appliques, trim, DIY, craft supplies, outlet covers, and so much more! 
Painting cabinets yourself is cost-effective -- a few gallons of paint, sandpaper, cleaner -- but the process is time-intensive. You can paint most cabinet surfaces, but proper prep is key to success. For laminate and melamine finishes, be sure to rough up the surface with 150-grit sandpaper, and apply a good bonding primer before topping it off with the color of your choice.
Some kitchen designs are beginning to display personality through eclectic and artistic approaches to kitchen hardware. Recent trends include nautical-themed rope drawer pulls and door handles, painted designs, numerals, insignias or monograms on drawer pulls. And pulls and handles made from antique buttons, glass or crystal will create a truly unique look that's sure to catch the eye and spark conversation.
There are a few options for hanging drawer hardware. Usually drawer pulls (or knobs or cup pulls) are centered on the face of the drawer. In a more modern kitchen, you may choose to hang them closer to the top of the face. For Shaker-style drawers, you can hang knobs or pulls either in the center of the drawer OR centered on the top stile. Which look should you go with? Whatever you like the best in your kitchen. Just make sure that you’re consistent across all the drawers. Drawers longer than two feet may look better with two knobs or pulls.
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
I love your site and your super helpful advice. We’re installing full overlay cabinets in our kitchen and we’re trying to select hinges for the upper cabinets — particularly the cupboard doors on the end which when closed is perpendicular to a wall. Since the door aren’t inset, I’m concerned we won’t be able to open the cupboard a full 90 degrees. Basically, the issue is how to solve the problem of the door swing? Are there any hinges that could solve this problem? I can send elevations if that helps. Thanks so much in advance!
New cabinet door hinges are costly, and you can save a substantial amount of money by repainting old hinges yourself. The preparation work will be the most time-consuming part of the process, but skipping this step could cause you more work later. Don't waste time using all-purpose primer; use a rust-inhibiting metal primer to ensure that the paint adheres. A top-quality paint will give the hinges a professional-looking finish.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.

2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
One of the first reccomendations I give on choosing hardware, is on wide drawers. Go with a single larger handle especially in the kitchen. The kitchen is a busy area and users find themselves with something in their hand when they go to open a drawer with the free hand. If there are 2 pulls on a drawer, just using one will end up tweaking the drawer in the long run. When I begin to look for a hardware collection always look at the range of sizes in that collection. I like the rule of the larger the drawer the larger the handle... or the more weight the drawer will hold the wider the stance should be that the handle provides.

If you think about it, you open your cabinet doors multiple times a day. Over a few years, that can take a toll on those hinges holding your doors in place. Replacing them with hinges that are made from a quality material like solid brass will not only help your cabinet doors function better, but it will make them look better, too! Choose a hinge color that matches the other hardware in your kitchen for a unified look and feel. For easy installation, look for hinges that are adjustable so you can use the same hinges to fit multiple sized doors and cabinets. This small change will make your cabinets look updated and keep them functioning properly for years to come.
Our drawer pulls come in a nearly endless variety of materials, styles and finishes. For a contemporary, modern look, try a brushed nickel or chrome drawer pull. If you’re considering a more traditional, classic style, check out our bronze, brass, pewter and black drawer pulls. You’ll be amazed by how a small detail like cabinet hardware can change the look of an entire room. Updating kitchen cabinet hardware, or furniture hardware is also a quick and easy exercise that requires few tools, minimal effort, and is relatively inexpensive.
Knobs have been around forever, and still function as a clean and classic hardware, with loads of practicality. Especially for cabinets that get used the most, knobs are still a perfect fit. Pay close attention to the color and size of knobs for white cabinets, and also be mindful of the finish. Are you looking for a shiny finish to match your white, modern kitchen? Or perhaps you prefer a matte finish, to accentuate your country style kitchen.
Also, experiment with different shapes. Things like knobs, handles, toilet paper holders, towel racks and hinges have a lot of expressive power. Beyond color, though, you should take advantage of their different shapes to accentuate certain features in a room. Pay attention to details like the width of drawers and the height of cabinet doors, and experiment with different shapes to complement them.
By adding hardware you like, you’re literally installing your style into the room — and this will make any accessories you want to add in feel like a part of the kitchen’s design, and not out of place. Of course, not every cabinet + hardware combo is going to work, but see how far you can take it when it comes to choosing hardware outside the traditional style of the cabinets.
First, you’ll want to do a thorough count of all your doors and drawers to make sure you know exactly how many new pulls and knobs you’ll need. To streamline the project, match your new hardware’s spread to the distance between the existing screw holes (you may need a tape measure). Or you can just take one of the old pulls with you to the store to shop.
Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
At a home renovation in Connecticut, cabinet fabricator Michael Madore experimented with what he calls an "aggressive" metal-sanding process to pull out the grain from the whitewashed oak plywood. For the hardware-free cabinets, Julie Salles Schaffer looked to a drawer pull detail derived from Giò Ponti’s work—though she admits the radial edging is an effect entirely her own.
Modern cabinet door hinges are a critical part to any cabinet, and are also quite complex; there are about a dozen (if not more) different types of hinges, depending on whether you have face-frame cabinets or frameless cabinets. Face-frame cabinets include a frame made of 1-½" to 2" wide solid wood that attaches to the front edges of the cabinets. This type of cabinet construction is common in American-made cabinets, and hinges will then mount directly to this frame. However, if you have frameless cabinets—which are typically made in Europe, like IKEA cabinets—your cabinets are basically just a four-sided box with no frame around the front edges. In this case, the hinges will mount directly to the interior of the cabinet. 
I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!
Kitchen cabinet knobs can really change the look of your cabinets. The best knobs and handles not only suit the cabinet style, but also add to the theme or mood of your kitchen. For example, the warm appeal of hammered copper cupboard handles blends well with rustic kitchens, while the cool sparkle of crystal knobs looks elegant against dark wood cabinets.
The first step in choosing kitchen hardware was to decide on the color and style. I fell in love with the selections offered by Atlas Homewares — so much so that I’m now thrilled to be partnering with them on this post. 🙂  I started by ordering several samples in various shapes, sizes and finishes so I could style them in person with the cabinets and countertops.
If you’re like me and love hardware (I think of it as jewelry for the house) and want your pulls and knobs to make a statement, instead of blend into background, you’ll want to choose hardware that contrasts with your cabinets, drawers and doors.  Consider using darker finishes like black or oil rubbed bronze on white or light colored cabinets and doors.  
Generally speaking, I like to see a combination of knobs and handles/pulls. Knobs or handles for the doors and handles or pulls for the drawers. If you are painting your kitchen, the extra holes can be filled, sanded, and smoothed prior to painting so you can start with a clean slate and choose any hardware for your update. I say “generally speaking” because lately I’m drawn to kitchens that have all handles like this “before” photo of a kitchen we recently updated.
×