For pulls on a flat front cabinet, the bottom corner of the pull should be equidistant from both sides of the cabinet. For Shaker-style cabinets, the same rules apply as with knobs: center the pull on the vertical stile, with the bottom of the pull even with the top of the horizontal stile (or the top even with the bottom of the horizontal stile, for a lower cabinet). These aren’t hard and fast rules—you may want to adjust them depending on what looks best for your cabinets and hardware—but they’re a good place to start.
Wine Logic wine racks are built-in right underneath your kitchen cabinets, eliminating the need to take up any counter space with a freestanding wine rack. Wine Logic racks come with two to five separate slide out trays that each hold up to six bottles of wine. And the best part is, Wine Logic’s horizontal design stores wine in the best possible condition, keeping the corks wet and the wine untouched by air.
There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.
3. Know when to use knobs over pulls. In traditional and country kitchens, putting a knob on a cabinet is not uncommon. In fact, with many cabinets, knobs may a better option than pulls. How do you know the difference? When kitchen cabinets are ornate or finely detailed, go with a knob rather than a pull. A knob is smaller and simpler and doesn’t take attention away from the design of the cabinets.
2. Keep finishes cohesive. You’ll find hardware in a range of finishes from brushed nickel to brass. While mixing and matching the hardware around your kitchen is fine, you should try to maintain the same finish and keep colors as close as possible. Sometimes you’re forced to buy hardware from more than one retailer, but when doing so make sure you keep finishes cohesive.
Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!
I would like to use a hinge similar to the wrap around no mortise Amaroc 3175s but am disappointed to learn the poor reviews ….sloppy….bent…flimsy…not worth it…low qc import. Perhaps they were better in the past! I would be most greatful if you could recommend a better quality hinge of that style. Alternatively,Can the full inset euro cup hinge be adapted to a face frame cabinet by building out the inside lip ^
The choice between cabinet pulls and knobs isn’t easy — both come with positives and negatives. Keep in mind that you’ll be using your knobs or pulls every day. Whatever you choose should feel natural in your hand and flow with the décor of the room. You should consider your kitchen’s décor and style, the look you want to achieve, your budget, ease of cleaning, ease of use, the weight of your drawers and more.
What is the existing decor of your kitchen or bathroom? For instance, if your kitchen has a white, Scandinavian minimalist aesthetic, you should try matching your hardware with it — in that case, perhaps something slender, jet-black and low-profile. Mismatching styles can look “off” and can create a confused sense of the room’s personality. However, it can also be done well. We’ll go into more depth on this below.
Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five. I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
Decide whether to install door catches. These will secure your doors while they are closed. Magnetic door catches are most often used. When your door closes, a small metal plate on the back of the door attaches itself to a magnet on the cabinet frame. You will hear a slight clicking sound as they make contact. Two additional styles that provide a smooth operation are spring-roller catches and friction catches. These catches are silent when they latch.
At this point, you will have narrowed down your hardware choices to a specific style, type, size and finish. Next thing to incorporate is your budget. A good starting point is to count how many knobs and pulls you will need for your cabinetry and determine a price range that is comfortable for you. Many hardware manufacturers have multiple lines of varying quality and price, so be sure to find a manufacturer that uses high-quality materials. Buying cheap can seem like a good idea in the short run, but cheaper metals will degrade faster down the road and face a much higher risk of breaking or bending. Stainless steel hardware, for example, should be solid (not hollow) with a durable but even finish.