You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls. Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center (Photo 1). You’ll use this line to make sure the angled top plates meet in the center.
• Violations of building codes — before the beginning of construction of your shed, it is important to check for the building conducts set by the authorities in your town. You are not supposed to begin any construction works before applying for a permit from the local authorities. This helps you avoid a lot of time being wasted in lawsuits, paying fines and such inconveniences. If you had already begun building your shed before your permit is authorized by the authorities, they will demand you to start all over again. That leads you spending more money on the construction of the shed. During fitting of electric lighting, you are supposed to involve a legally certified electrician to avoid the long arm of the law and to avoid accidents as electrocution and even fire. The same laws apply to gas and water pipes installation.

The front wall has a 6-foot-long top plate and two 1-foot-long bottom plates, leaving space for a 4-foot-wide door. The four wall studs are 81 1/4 inches long; install them as shown in the front framing detail at left. Next, install the 73-inch-long jack studs, and then attach the 51-inch-long doubled header. Finally, attach the 6 1/4-inch-long cripple studs.


We now need to create a base that we can nail the frames for the walls into.  We did this with four 2x8's and some bent i-bolts along with a lot of mortar.  The basic process was that we bent the bottoms of the i-bolts after heating them with a blow torch, and then anchored these in some of the holes in the cinderblocks with a lot of mortar.  Then we drilled holes in the 2x8's where the i-bolts were and put these on top and screwed them in.  The frames can now be solidly attached to the base with the framing hammer.
At MOTHER EARTH NEWS, we are dedicated to conserving our planet's natural resources while helping you conserve your financial resources. You'll find tips for slashing heating bills, growing fresh, natural produce at home, and more. That's why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.95 (USA only).
The Glidetop Slide Lid shed from Suncast features an ultra tough resin construction that makes it one of the most long lasting and easy to maintain sheds on the market. The gliding lid makes walk-in access quite easy, and the reinforced floor makes the shed perfect for tractor support. Perfect for storing all kinds of things, like patio furniture, mowers, bikes, and wheelbarrows. It’s easy to lock the shed and protect everything inside, year-round. The extra secure roof on the Suncast is what makes it really stand apart from its competition. It doesn’t stand too tall, so if you need to keep your shed below fence level then this is the ideal model for you. Suncast is one of the leaders in durable, affordable sheds, and this model is a great choice if you’re looking to save a little money and still have a storage unit that is going to last you for years to come. The assembly of the Suncast is incredibly easy and requires minimal tools to set-up.
My advice... Don't do-it-all-yourself. Novice and pro alike can benefit from each other in DIY. You might have the shed location leveled by a landscaper; get a referral to outsource the shed's foundation to a building subcontractor; you can even have the roof's trusses made by a local truss company and the shingles installed by a handyman or roofer.
Don’t let another dictate your choices. With our FREE and PREMIUM plans, all you need to is select the dimension you want, download the plan and start right away. We have more than 40 FREE shed plans available to download. Various dimensions, shapes and sizes available. If FREE PLANS are not good enough for you and you want more details, please consider our PREMIUM PLANS. These plans not only give you the entire shed’s dimensions but also dimensions of the foundation, walls, doors, windows and the like, but much more! Everything is laid out in plain words. Determine the size of shed you want to go for, download our guides and start building your very first shed right away.
Cut the sill piece and assemble the windows with pocket screws. Using a router with a 3/8-in. rabbet bit, rout a 3/8-in.-deep recess on the back of the window to receive the 1/4-in. Plexiglas acrylic sheet (Photo 14). Set the window frame, recessed side down, over a piece of acrylic sheet and trace the shape with a permanent marker. Cut the curve with a fine-tooth jigsaw blade and the straight sections with a fine-tooth blade in a table saw or circular saw.
If you buy heavy galvanized hardware designed for farm buildings for your shed, it’s overkill. Buy heavy-duty closet door hardware instead. It’s not really meant for outdoor use, but when it’s protected by an overhang, it holds up well. And if the roller bearings get corroded, it’s simple to replace the entire hanger mechanism. Check out Johnson Hardware’s 111 track and 1025 ball-bearing hangers.
There are a lot of plans and designs to choose from when building the shed, so make sure you take a look over several alternatives before starting the actual construction. Invest in weather-resistant lumber (pressure-treated lumber), making sure all the components are in a good condition and perfectly straight. Drill pilot holes before inserting the screws, to prevent the wood from splitting.
The construction of a wood foundation is usually built using pressure-treated 2x6 lumbers. These parts are called the band on the ends and the joist in the middle of the band, spaced out 16-24 inches apart. The foundation frame will sit on top of pressure-treated 4x4 posts called skids. The skids will set on the cinder blocks or on top of gravel to prevent rot.
Then, you will need to install a series of floor joists across the entire length of the support beams; these will need to be the same length as the distance between the two rim joints so that they’ll fit between them. In the example design, the floor joists are all separated by 14.5-inch gaps except for the outermost two, which are 13 3⁄4 inches (34.9 cm) from their immediate neighbors; this is to allow a standard piece of plywood to line up with the outermost edge of the outermost joist but only cover half of an interior joist, allowing its neighbor to cover the other half so that both can be supported properly.[3]
Working from ladders is more dangerous than working from scaffolding. Plus, having to constantly move ladders around is time consuming. When you get to the roof construction, consider renting a set of scaffolding with wheels. You’ll be amazed at how much easier it is to have a stable platform to work from and to set your tools and materials on. You can rent a 5-ft.-tall section of scaffold with three planks and wheels for about $110 per week.

DIY Shed Plans

×