The best spot for a shed is level, well-drained ground close to where you work in your garden or yard. The location doesn’t need to be perfectly flat; the foundation design shown in the plans allows for adjustments to make the floor level. Small sheds require only a top-of-soil foundation, even in locations with freezing winter temperatures. Precast concrete deck blocks work perfectly for this.

You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls. Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center (Photo 1). You’ll use this line to make sure the angled top plates meet in the center.
Omit the bird’s-mouth from four rafters and use these on the ends. Cut the 2x4s for the ridge and subfascia to length and mark the rafter positions on them. Line up the rafters with the marks and nail through the ridge and subfascia with 16d nails to secure them. When the roof frame is complete, line up the subfascia with the chalk line on the platform and tack it in three or four places with toe screws to hold the frame straight while you install the soffit.
To be honest, I almost named this project “How to Build a Shed from Scratch with your Spouse and Not Bury them Under the Concrete.” Working together as a team in life is one thing, but working together on a home DIY project is another. It’s like being on a drunken see-saw with “stay out here and work with me, but don’t get in my way.” Or, “keep me company, but don’t talk to me” How about, “just play with the kids while I work but keep them away from what I’m working on” Or even “Get me this tool, get me that tool, where are my tools? Don’t touch the tools” As it turns out that title is just a bit too wordy anyway, so I had to shorten it up a bit.
The trick for learning how to build a storage shed is to stretch the line across a scrap of wood at each end so there’s a space between the line and the part you’re straightening. On a wall, for example, tack small scraps of 1/2-in. plywood at each end of the top plate and stretch a line very tightly over the plywood. Then use a third scrap as a gauge to check the distance between the line and the lumber. Use braces or whatever is needed to adjust the top plate until the gauge just fits. Now your top plate will be perfectly straight.

After laying out the 12 blocks, use a straight 2 x 4 and a 4-ft. level to ensure that all the blocks are level. Shim up any low blocks with strips of asphalt roofing, cedar shingles or 2-in.-thick concrete patio block. Next, form each front and rear band joist by nailing a 2 x 6 to a 2 x 8 mudsill. Set the mudsills on top of the blocks running across the front and rear of the shed. Cut a third 2 x 8 mudsill to fit along the tops of the center row of foundation blocks.
When you nail on the siding, make sure it overhangs the framing on each side by 3-1/2 in. and that you’ve trimmed off the top corner to follow the slope of the angled top plate (Photo 2). Attach the siding with 2-in. galvanized or stainless steel ring-shank siding nails placed 8 in. apart along studs and 6 in. apart along the edges of the sheets. You’ll have to nail blocking between the studs to support the top edge of the siding and the Z-flashing.
Because My Shed Plans does not promise anything beyond belief, the product’s foundation is pretty strong. People have enjoyed choosing between the collections of shed layouts and building it themselves. It’s a great activity for the whole family, since it’s all well planned out. It can be a bonding experience, the way a team building exercise at work is.
If you decide that you don’t want the second package after purchasing the first package, you will be offered a third package which is even more explicit that contains tonnes and tonnes of woodworking plans that are laid over thousands of pages. All these eBooks are neatly organized, very much real and indeed the amount of plans that they contain might even come out as nauseating, if you’re someone who doesn’t have so much of patience to go through all of them.
If you are looking for the best collection of outdoor shed plans, then look no further. ‘My Shed Plans’ by Ryan Henderson’ is perhaps among the best collection of shed plans you can find anywhere today. It is a collection of around 12,000 woodworking plans which are designed to cater to the needs of both professional and amateur woodworkers. With over 20 years of experience in shed building, Ryan is an authority in the field. His plans are explained well with step by step instructions. If you follow his shed plans and instructions properly, you will be able to build one with ease. It doesn’t matter if your woodworking skills are basic or if you have failed in making a shed before, by following his shed plans you can undertake any such project with confidence.
Woodworking is an art, and like most art forms, it only require dedication, skill and time. Good thing you have our shed plans. You wouldn’t be spending months figuring out how to cut wood pieces, etc. You will get enough guidance to start right away and build a gorgeous shed for your garden. The benefit? You would learn how to build sheds within days. No experiments and no wasting time!
It’s vital to build your shed on a stable, level location—and never in a wet, low-lying area or on a downward slope. And no matter how well a shed is constructed, it won’t hold up on a weak base. A proper foundation is key, one that sets the shed slightly off the ground to aid water drainage and reduce moisture transfer. There are different foundation options, depending on where you live and the size and intended use of the shed, so bone up on the fundamentals and assess your options with this advice from the LP Outdoor Building Solutions team.
To make it easier for you, the “do-it-yourself” storage shed kits are for sale partially prefabricated to make the assembly of the shed barn kit simple and straightforward. The DIY storage shed kit walls are assembled and the rafters are prebuilt and ready to put into place. While we offer large shed kits as well as small barn kits, on the smaller 6′ and 8′ shed kits, the floor may be partially constructed to make the job even easier.

If you need lots of space for storage, garden room, or office space, the most common design will be the gable shed. The gable roof design has two sloped roof that resembles a little house. This design is the most popular because it blends will with your home. The gambrel shed resembles a barn. It is great for storage as no space will go to waste. A larger size gambrel shed will have enough room to build a loft. Having a loft will keep everything organized and allow you to store more stuff. By installing a ramp to the shed you can also store ATV, snowmobiles, jet skis, trailers, and such things. 

• Stagnant waters — As much as the wood is coated to protect it from water, it would still be advisable to keep the wood away from stagnant waters. This is as the wood coating is not a permanent coat and so is the wood is exposed to water it will get damaged over time. The best way to avoid water paddles near the shed is building gutter systems on its roof which directs the water to a tank or a pool.
How big should a garden shed be so it can be practical without occupying more space than it has to? Well…it depends. I think this cute little garden shed from acultivatednest has one of the smallest possible footprints. The fact that it’s small but tall allows it to be quite practical. It’s great for the storage of garden tools and there’s even some room for a shelf or two or for a few hooks on the walls.
• Purchase of two small sheds — it is dangerous to underspend just as it is to overspend. This is because you may underspend and the shed purchased may end up being of little use below your expectations. This will prompt you to build another shed and that will lead you to overspend. A shed may look simple on the outside but it is how you customize your shed that will determine the volume of goods your shed can hold. When building your shed it is important you identify each and every section of your shed, allocate the tools to each section and then modify the shed to hold each and every tool at its place. In that manner, you end up maximizing each and every space in your shed and also utilizing your shed to its maximum capability. It is also recommendable to have adequately spaced sheds where one can perform outdoor activities like car repairing in the shed when the weather is not favorable. Before starting your shed building, think of all its purposes and all the outdoor and semi-outdoor activities one could perform during unfavorable weather condition or any other related circumstances.
DIY Storage Shed Kits are the same price as a regular shed. We simply partially assemble the shed kit and send it as a package for you to assemble. If you wish to have Sheds Unlimited assemble the shed kit for you there is an extra cost from 25% to 40% depending on the type of storage shed or prefab car garage you wish to purchase. The prefab cost is also added to any options on the building. In addition, there may be extra storage shed kit shipping charges depending on your location.
· Firewood storage sheds — mainly used to store firewood from elements of weather such as rainfall that may destroy them. The most common type of firewood shed is the lean on shed. It is also the most suitable as it allows free circulation of air, therefore, preventing dampness of the firewood. It is also near the house so the firewood is stored near your house and may access anytime you need them.
We have a large selection of small horse barn plans, tack rooms and run in shed plans. Each of our designs comes with a materials list and construction plans to help you save time and money when you build. We have many different sizes of horse barns including one, two, three and four stalls. Most of the barns and run in sheds are designed to be built with pine board and batten siding on the outside and a 4' tall Oak kick board on the interior.

Cut the sill piece and assemble the windows with pocket screws. Using a router with a 3/8-in. rabbet bit, rout a 3/8-in.-deep recess on the back of the window to receive the 1/4-in. Plexiglas acrylic sheet (Photo 14). Set the window frame, recessed side down, over a piece of acrylic sheet and trace the shape with a permanent marker. Cut the curve with a fine-tooth jigsaw blade and the straight sections with a fine-tooth blade in a table saw or circular saw.
Before we can finish the base we need to get the electrical ready.  Put a peice of conduit over your electrical wire to protect it from any damage it could receive while you are finishing the base and to give the shed a more finished look.  Make sure the pipe and wire inside are pointing up perpendicular to the ground and are preferably going straight to the location where your first outlet will be.

We decided to construct the foundation of our shed out of cinderblocks.  This will help keep out any rodents, and doesn't risk harming the trees beside the shed.  In order to lay a good foundation, we first had to level out the ground. We didn't need to level out the middle of the structure's base because that was later filled with limestone screening.  We made channels for the cinderblocks with spades and a pickaxe, and made sure to create a channel for the electrical as well.  The electricity comes from our house, which is about 10 feet away from where the shed stands.
Staining: There are two types of staining. These can either be natural where the stains are purposed to enhance the beauty of the wood or unnatural means which involve activities like painting the wood. In natural means, one has to keep maintaining it frequently as they last for approximately two years while unnatural means last as long as up to eight years without needing any maintenance.
To be sure, the whole permitting process can be a bit intimidating. And, if I'm being honest here, I've never been comfortable dealing with the city and all their codes - seems they're always moving the line on me. But, I always make it a point to be friendly with the Building Inspector. He's there to help and can be a fountain of information, when building your wood shed.
2012: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2013: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2014: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2015: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2016: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2017: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2018: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2019: 1, 2, 3, 4, 5,
For strength, plan to build the front and back layers so the corners overlap each other. Then, to accommodate inset panels, make the front pieces a little wider to create a lip for the panels to rest against. Use plywood or tongue-and-groove boards for the panels, and hold them in with stops nailed on the back. You can assemble the two frames with pocket screws before gluing and screwing them together, but it’s not necessary. After the glue dries, plane or sand the edges to hide the fact that there are two layers.
Would we do it again? I won’t sugar coat it, this is real life so probably not. Some things aren’t worth the aggravation or the stress. In the end, we didn’t save that much money by building the shed ourselves. I think the total cost was around $1200. But I can tell you one thing, if we are ever attacked by zombies or if there is an Armageddon I am hiding in the shed because the big bad wolf can huff and puff and nothing is taking this structure down. 
Build the framework for the back wall. Make the top and bottom beams (a.k.a. the plates) the same length as the length of the floor which they sit. To keep your measurements simple, make the spacing between the vertical studs identical to the spacing between your floor joists. Note that the back wall should be lower than the front wall so that the roof slopes and directs rain away from the door.[6]
We assembled each layer with pocket screws before gluing the two layers together, but if you don’t own a pocket hole setup, you could simply screw through the overlapping boards instead. Complete the door frame. Then cut the 4 x 8-ft. grooved plywood to fit the lower recess, and cut a piece of 1/4-in. acrylic sheet to fit the upper recess. Secure the plywood and acrylic sheet with 1/2-in. x 1/2-in. moldings nailed to the inside. Sand the edges of the door flush.
• Use of crooked studs — while building the shed, one would build a shed with crooked studs which may render the shed unstable. It is advisable that as one is building a shed to ensure that all the studs used are straight and uncompromised. That will ensure that the body frame of the shed remains strong enough to hold its own weight and be durable enough for a long time.
Don’t assume that you’re missing something if you have a question that cannot be answered within the guidelines of the shed plans. Builders at all levels will always have questions and it is better to ask the question than miss something important in the process. Go online and find a forum or a video if you have a question. Better yet, read all the little print that you skipped over in your shed plan and see if the answer is there, it might be.

Ryan had a difficult time building his own first shed. Wrong material, wrong measures, wrong techniques, all of them didn’t help in making the shed any quicker. It took him 6 months to complete his first shed project, and at the end of it he was worn out and exhausted. Even after spending a lot of time reading and purchasing woodworking books, blueprints, nothing seemed to work. Most of the shed plans he bought lacked vital information which left him with more questions than answers. That is when he decided to leave it all aside and build his own shed plans. That was the beginning of his work towards building his master collection of shed plans.


The shed we built rests on a foundation made up of 12 solid-concrete blocks. The 4 x 8 x 16-in. blocks are arranged in three rows spaced 59 in. apart. These blocks are typically set directly on the ground, but we put down a 4-in. bed of gravel first because our site occasionally receives groundwater. The gravel will keep the soil beneath the shed from eroding or becoming soggy.
The sheds available can be distinguished easily as they come in pale green that eventually fades into silvery grey. The Pressure treated sheds are relatively a bit costlier than the DIP treated sheds and the advantage of using them is that they don’t need further preservative treatment and can serve the whole during the entire ten years saving a lot of time and money.​
A How To Buid A Shed e-Book that comes free with every shed plan order. This e-Book has over 50 pages of illustrations showing each step to building all the roof types shown on our shed building plans, how to frame shed walls, how to frame a shed floor, how to install siding, how to build roof rafters and trusses. It also includes nailing schedules and optional roof details.
2012: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2013: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2014: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2015: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2016: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2017: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2018: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12  |  2019: 1, 2, 3, 4, 5,
It’s unconventional, but building the roof upside down on the platform has advantages. First, you avoid a lot of ladder work. And second, you can nail the soffit material to the overhangs easily without having to work overhead and in cramped spaces. You do have to take a little extra care to make sure the framing is square and the perimeter 2x4s are perfectly straight before nailing on the soffit, though. Start by cutting out the rafters using the pattern in Figure D as a guide.
The advertising was incredibly misleading. The early indications (at least via ********) are that you can purchase downloadable shed plans. Further claims are made that **** ********* is offering something unique in the detail and instruction, such that someone with no building experience could purchase material, fabricate, and build these sheds. First, that is not at all the case. most of these "plans" are only one-page shots. Second, most of the plans couldn't be build even by someone who is in construction or familiar with building. This stops just short of being a SCAM. At the very least, it's extremely misleading. **** ********* should be ashamed of himself.
Made from durable blow molded resin, this Alpine shed from Suncast comes complete with 14 windows with delightful contrast trim. The double doors are built with articulating metal hardware so they’re robust and durable. The floor is reinforced for the ultimate sturdy foundation. Extra roof support is provided by the metal trusses and ridge beaming. This shed is perfect when you’re looking for something that is built tough, and stands out beyond the more flimsy and cheap designs that you find on the market. It is large enough to stow everything that you need and keep all items clean, safe, and secure. The outer appearance of this shed makes it perfect for those who want an attractive external design that doesn’t stick out like a sore thumb in your yard. All in all, customer reviews across the board are quite positive for this shed, and it makes a great addition to anyone’s home.
Ryan had a difficult time building his own first shed. Wrong material, wrong measures, wrong techniques, all of them didn’t help in making the shed any quicker. It took him 6 months to complete his first shed project, and at the end of it he was worn out and exhausted. Even after spending a lot of time reading and purchasing woodworking books, blueprints, nothing seemed to work. Most of the shed plans he bought lacked vital information which left him with more questions than answers. That is when he decided to leave it all aside and build his own shed plans. That was the beginning of his work towards building his master collection of shed plans.

We assembled each layer with pocket screws before gluing the two layers together, but if you don’t own a pocket hole setup, you could simply screw through the overlapping boards instead. Complete the door frame. Then cut the 4 x 8-ft. grooved plywood to fit the lower recess, and cut a piece of 1/4-in. acrylic sheet to fit the upper recess. Secure the plywood and acrylic sheet with 1/2-in. x 1/2-in. moldings nailed to the inside. Sand the edges of the door flush.


Backyard Shed Plans Barn Shed Plans Chicken Coop Plans Compost bin Plans Corner Shed Plans Detached Garage Plans Dormer Shed Plans Firewood Shed Plans Garage Shed Plans Garden Shed Plans Generator Shed Plans Greenhouse Shed Plans Hip Roof Shed Plans Horse Barn Plans Large Shed Plans Lean To Shed Plans Loft Shed Plans Low Income Housing Plans Metric Garden Sheds Modern Shed Plans Porch Shed Plans Run In Shed Plans Saltbox Shed Plans Short Shed Plans
×