Hello Instructables!  This is my entry into the Shopbot Contest.  This Instructable will show you the steps to building your own shed.   We decided that our shed would be for storage because we wanted to get some stuff out of the garage so we can use it as a shop.  One of the challenges of building a shed in our backyard was that the ground was sloped in the area that we wanted to put it, so we had to find a way to get around that.  Another was that we are building beside some well established trees, and we didn't want to harm their root structure.  This is why we went with cinderblock and mortar rather than poured concrete.
Building something yourself, especially something as big as a shed, is always rewarding, but not only will it feel good to have a self-made beauty in your backyard, it’s times lower in cost than buying a shed. In fact, building a small shed can cost as little as $100! That’s a pennysaver! And well, all proper DIY wood projects should be, ain’t that right?
They are the simplest and cheapest sheds one may find. They are easily assembled by regular people, they do not require initial construction knowledge. One may find the DIY kits and plans for these type of sheds. The most common type of sheds is plastic and wooden. They are mainly used to store garden tools, tractors and store items that are considered unsafe to be stored indoors such as gasoline and agricultural chemicals.
For strength, plan to build the front and back layers so the corners overlap each other. Then, to accommodate inset panels, make the front pieces a little wider to create a lip for the panels to rest against. Use plywood or tongue-and-groove boards for the panels, and hold them in with stops nailed on the back. You can assemble the two frames with pocket screws before gluing and screwing them together, but it’s not necessary. After the glue dries, plane or sand the edges to hide the fact that there are two layers.
You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls. Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center (Photo 1). You’ll use this line to make sure the angled top plates meet in the center.
The men showed up early Tuesday and went right to work.They were polite, friendly and answered any questions I asked. Although my building was on the larger side, 28' by 44' ft. they worked well together and finished in two days! Myself and two contractor friends inspected the building and were all quite pleased with the quality of the building. The men cleaned up the perimeter before leaving and other than a new building you would never know they were there. I am very pleased and would definatly recommend Sheds Unlimited.. 
Well, if you look at the name of the project, it doesn’t actually appear to be what it says. The title says that Ryan Shed Plans also known as MyShedPlans contains a compendium of 12,000 Blueprints. But if you look at the package carefully, the phrasing on the website contains 12,000 Woodworking Shed Plans and Shed Designs. Most of the blueprints are ShedPlans that cover both small scale and big scale projects, and you can come across thousands and thousands of different blueprints with different architectural, functional and aesthetic features.​
For the shed's floor deck, use ¾-in. exterior-grade plywood; anything thinner will flex between joists. (Note that a double layer of ½-in. exterior ply is okay, too.) If you plan to store heavy items, such as a lawn tractor or woodworking machines, consider using ¾-in. tongue-and-groove plywood. This costs slightly more, and is a bit more troublesome to install, but its edges lock tightly together, creating a rock-solid, rigid floor. In areas with excessively high moisture and large numbers of wood-boring bugs--such as Florida, Alabama and the other Gulf Coast states--consider using pressure-treated plywood for the floor deck. It's particularly resistant to moisture and insects.
Well I give this jerk credit for his pervasive techniques of getting people back to his website. If you see a review that says Ryans Shed Scam and click it it takes you to his website and it is not a website where you can read about his scam. THis is the biggest rip off I have ever fallen for. Everything is not as advertised. You get 2 plans bnot 12,000. You get lots of articles not books written in 1864, or 1903 and you like reading about obsolete, useless article then this is the plan for you. I am totally disgusted!!!!
It’s not always possible, but if you’re using 4 x 8-ft. sheet siding and have enough helpers around to lift the wall when you’re done, you can save time by siding the walls before you raise them. Make sure to straighten the wall plates and square the wall by measuring diagonally before you nail on the siding. This is easier to do on a wood shed floor because you can tack the plates to the floor to hold the wall straight and square while you install the siding.

The plans are pirated copies, some from "mycabinandsheds.com" as well as scanned 100 year old books . They are basic plans of very limited value. I clicked on a link from a "Kim Komando" email and saw the add for 12000 plans and I figured it was a trusted advertiser. Come to find out after contacting Komando that there are 3rd party advertisers she would take no credit for endorsing. I should have done more research before I paid for anything but after finding out it is a scam I called the 1-800-390-6035 click bank number and they gave me a refund with no arguing at all.

· Wood sheds — these types of sheds are made of wood. They are the most common type of shed compared to metal and plastics. They are the most conducive as they can be used as children playhouses, outdoor office and still storage of garden tools. They are also easy to modify and renovate as increasing their size. They are preferred to other types as they blend well with the environment and give the environment a good natural look. However, they must be maintained regularly from insects as termites which feed on wood.
There are over 12,000 different shed plans and woodworking endeavours for you to choose from, so the projects are pretty much endless. You are given everything you could possibly need to build your own beautiful outdoor shed. For those who already have years of woodwork and carpentry experience, My Shed Plans may not offer you enough information that you don’t already know. The only benefits you’ll get from the package are the innovative shed blueprints and designs, which can be help enough.

The design of the shed you choose will depend on what you will be using it for and were it will be located. If you just need a small shed to place garden equipment, a lean to shed can be ideal. This design of shed will not take much room and it can be placed next to a fence or wall. The lean to shed has a single sloped roof design. It is one of the most common for garden tools as well as pool equipment and chemicals.
Once redirected to the webpage, I found a bewildering list of links, and downloads. Some were redundant, some didn't work. And I kept trying to figure out where the 12k plans were. I thought for what I paid I should be able to plug in my parameters into a query and get something that remotely looked like an organized list of plans that matched my query. But nada. Nothing. Zilch. Just piles of pdf's tucked seemingly haphazardly into folders here and there, listed in not too logical order in links on a webpage.
Build the framework for the side walls. The bottom plate of each side wall should be the same length as the distance between the bottom plates of the front and back wall (so that the side walls will fit between them). The standard spacing between vertical wall studs in the US is 16 inches (from center to center, not from edge to edge); since this stud spacing doesn’t perfectly divide into the total length of the side walls in the example design, the two outermost studs make up for this discrepancy by being slightly closer to their neighbors. Most importantly, the top plate is angled so that the roof will be sloped, which makes the height of each vertical stud slightly different. If you’re not sure how to calculate the necessary height of each vertical stud in advance, make the two outermost vertical studs first, lay them the correct distance apart, cut a top plate that spans this distance, and then cut each remaining vertical stud individually based on the distance between the top and bottom plates at that exact location.[8]
No shed, regardless of how well it's built, will last long if it's set on a weak base. Most sheds can be supported by an on-grade foundation, which consists of solid concrete blocks or pressure-treated wood timbers set directly on the ground. The concrete blocks or timbers (aka skids) must be leveled and spaced closely enough to properly support the shed's floor frame. Note that it's important to use solid concrete blocks, not hollow wall blocks, which can easily crack.

If you have the do-it-yourself skills and an open timeframe, check out the various plans available online or for purchase. Make sure you thoroughly understand the instructions and actually have the ability and tools to do the job. Other sources for sheds include prefabricated buildings that you would order from a reputable company and kits. Some include pre-cut lumber that is shipped to your house. Before ordering, find out if additional milling, drilling, or cutting will be needed, along with necessary tools.
So it's not surprising that people often ask me for advice about putting together a backyard storage building. Sometimes I get asked questions that I couldn't possibly answer: "Do you think my husband and brother-in-law can build me a garden shed?" Or, "Would an 8 x 10-ft. shed be big enough to store all my stuff?" Gee, ma'am, I couldn't say. But often, the questions have something to do with shed design, framing or siding options. There, I can help. And so with these inquisitive souls in mind I present my favorite tricks of the shed trade.
Listen, about the My Shed Plans Scam… all you can say is haters are gonna hate. There are way too many people on the web going about trying to ruin things for others. It probably makes them feel bigger than the basement of their parents’ house allows. In regards to your My Shed Plans product, it looks like a great deal. 12,000 shed plans, all in one package? Seriously, is there any plan that’s missing?
The female version of man caves is she sheds: havens to escape that can be designed and decorated in whatever style the owner desires. Inspired by a tiny hummingbird viewed nearby, this shed is aptly named Hummingbird Cottage. Lovely photos on Instagram reveal that the shed is used for art projects, as a retreat, displaying vintage pottery, and for entertaining friends. Extras like a hanging faux-crystal chandelier, potted flowering plants, wreaths, and stained glass give it a personal touch.
It’s unconventional, but building the roof upside down on the platform has advantages. First, you avoid a lot of ladder work. And second, you can nail the soffit material to the overhangs easily without having to work overhead and in cramped spaces. You do have to take a little extra care to make sure the framing is square and the perimeter 2x4s are perfectly straight before nailing on the soffit, though. Start by cutting out the rafters using the pattern in Figure D as a guide.

A shed is a simple roofed single floor structure that is used for storage of garden tools, shelter domestic animals, performing out hobbies and also as a workshop. They can also be referred to as outhouse, outbuilding or shack. They are mostly situated in the back garden. Sheds vary in their sizes from large sheds to small sheds depending on their purposes. Storage sheds are mostly small in size but industrial and farm sheds are mostly large depending on the volume of the goods they hold. Sheds can be built from different materials like wood, metals, and plastic. The types of shed construction include metal sheathing, plastic sheathing, and complete wood construction.

How big should a garden shed be so it can be practical without occupying more space than it has to? Well…it depends. I think this cute little garden shed from acultivatednest has one of the smallest possible footprints. The fact that it’s small but tall allows it to be quite practical. It’s great for the storage of garden tools and there’s even some room for a shelf or two or for a few hooks on the walls.


Ø Clay tiled sheds — as the name suggests, these are sheds that their roofs consist of clay tiles. The clay tiles make the wooden sheds look visually appealing. Nevertheless, one has to plan for the clay tiles from the foundation of the shed so that it can support the roof due to the bulkiness of the roof. The wooden walls need to be strong enough to support the roof. It would be advisable to hire an expert to install the clay tiled roof to avoid complications.

… Just in case this is NOT enough shed Plans for you, take a look below. There’s a whole lot more! This is just a taste of the staggering amount of shed plans and woodworking projects available. The biggest problem you’ll have with Ryan’s Shed Plans is, you won’t know which storage shed plans to choose from. The choices and different styles of sheds are endless!
A shed isn’t something you see people build…at least not very often. It’s rather the type of structure you discover in the backyard when you purchase an old house. So how do these things appear? They’re obviously built so let’s see what it takes so put a shed together. We looked around and we found a bunch of shed plans that we’d like to share with you. They’re pretty simple and you don’t need much experience with this sort of projects to be able to pull it off. They’re all customizable so you can enjoy them whether you want a pretty she shed or a manly workshop.
To be honest, I almost named this project “How to Build a Shed from Scratch with your Spouse and Not Bury them Under the Concrete.” Working together as a team in life is one thing, but working together on a home DIY project is another. It’s like being on a drunken see-saw with “stay out here and work with me, but don’t get in my way.” Or, “keep me company, but don’t talk to me” How about, “just play with the kids while I work but keep them away from what I’m working on” Or even “Get me this tool, get me that tool, where are my tools? Don’t touch the tools” As it turns out that title is just a bit too wordy anyway, so I had to shorten it up a bit.

The shed we built rests on a foundation made up of 12 solid-concrete blocks. The 4 x 8 x 16-in. blocks are arranged in three rows spaced 59 in. apart. These blocks are typically set directly on the ground, but we put down a 4-in. bed of gravel first because our site occasionally receives groundwater. The gravel will keep the soil beneath the shed from eroding or becoming soggy.
You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls. Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center (Photo 1). You’ll use this line to make sure the angled top plates meet in the center.
Pasadena, California, is known for its Craftsman style homes, a great number of which have been carefully preserved and restored. Owned by a University of Southern California (USC)-educated architect, Nott & Associates specializes in the Craftsman style. For a backyard shed, Nott custom designed and constructed the wooden doors, which include period-perfect details and hardware.
Start by setting deck blocks on the ground, positioned as shown in the plans. While the area doesn’t have to be perfectly level, you should make the ground roughly level where each block will rest. Temporarily place some straight 2-by-6 lumber on edge in the top grooves of the blocks to orient the blocks in a straight line. Arrange two rows of four blocks parallel to each other to form both long walls, then measure diagonally across the outside corners to determine how square the arrangement is. If the two long walls are parallel, and diagonal measurements taken across corners are equal, then each corner is guaranteed to be 90 degrees. Finish up by placing one deck block in the middle of each 6-foot wall after you have aligned and squared the 8-foot walls.
×