Any person interested in the field of woodworking will tell you how much time and effort it goes into building a wood project. And even after putting in so much effort, the chances of mistakes and failures are pretty high. So much so, that after a time you will feel like giving up altogether. Most people spend a lot of time and money on their first shed project and often end up frustrated because what they finally create is nothing like they wanted to. Why? The measurements were all screwed up! If that sounds like your story, it is finally going to change.  With Ryan’s collection of shed plans in your arsenal, you will never ever have to look for shed plans anywhere else.
Thanks for sharing such detailed plans Seamster. I'm hoping to build a very small lean-to tool shed (2.5X4.5' base) for my very small yard and this has given me a lot of insight. Currently, theor the table and mitre saws I inherited are stored in our spare bedroom... eventual nursery room. I want to get them into their own space outdoors sooner than later. Here in North Carolina with the humid summers I think it would be best to add some housewrap to the walls to help protect the tools. I also have a situation where the back wall will only be 4-6" off the house so need to construct/panel my walls before erecting them. Do you know if it's reasonable to panel then wrap each wall frame, side it and then finally erect and fasten? Would be very grateful for your thoughts!
The sheds available can be distinguished easily as they come in pale green that eventually fades into silvery grey. The Pressure treated sheds are relatively a bit costlier than the DIP treated sheds and the advantage of using them is that they don’t need further preservative treatment and can serve the whole during the entire ten years saving a lot of time and money.​
Complete the siding, then remove the toe-screws and move the wall aside to make room for constructing the opposite wall. Use the same chalk line template and process to build the opposite end wall. Figure C shows framing details for the front wall. Mark the curves on the 2×10 header pieces using the trammel setup shown in Photo 12 and Figure G. Cut them with a jigsaw. When you’re done building the front and back walls, set them aside so you can use the platform to build the roof sections.
Build the framework for the side walls. The bottom plate of each side wall should be the same length as the distance between the bottom plates of the front and back wall (so that the side walls will fit between them). The standard spacing between vertical wall studs in the US is 16 inches (from center to center, not from edge to edge); since this stud spacing doesn’t perfectly divide into the total length of the side walls in the example design, the two outermost studs make up for this discrepancy by being slightly closer to their neighbors. Most importantly, the top plate is angled so that the roof will be sloped, which makes the height of each vertical stud slightly different. If you’re not sure how to calculate the necessary height of each vertical stud in advance, make the two outermost vertical studs first, lay them the correct distance apart, cut a top plate that spans this distance, and then cut each remaining vertical stud individually based on the distance between the top and bottom plates at that exact location.[8]
There are over 12,000 different shed plans and woodworking endeavours for you to choose from, so the projects are pretty much endless. You are given everything you could possibly need to build your own beautiful outdoor shed. For those who already have years of woodwork and carpentry experience, My Shed Plans may not offer you enough information that you don’t already know. The only benefits you’ll get from the package are the innovative shed blueprints and designs, which can be help enough.
High-quality materials may cost a bit more, but they’ll save you time, trouble, and money in the long run. The chart here shows how LP® SmartSide® Panels compare with untreated plywood, vinyl, and galvanized metal. No wonder so many pros recommend sheds made with beautiful, durable LP products! If you want your shed to resist splitting, cracking, decay, and termite damage while duplicating the good looks of rich, real cedar, choose LP SmartSide® products.

Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Mail-in Rebate is in the form of merchandise credit check, valid in-store only. Merchandise credit check is not valid towards purchases made on MENARDS.COM®. By submitting this rebate form, you agree to resolve any disputes related to rebate redemption by binding arbitration and you waive any right to file or participate in a class action. Terms and conditions available at www.rebateinternational.com®


Finding MyShedPlans seemed too good to be true; 12k shed plans, 3-D renderings, detailed material lists, but wait, there's more! Hundreds of useful guides, woodworking books, and project ideas ranging from birdhouses to bridges. And what was more, was the promise of an easy download and immediate access to boundless amounts of material so I could be right on my way to a sharp new shed.
Ryan Henderson is a master woodworker with over 30 years experience and has developed Ryan’s Shed Plans.  This is a detailed digital book with 12,000 shed plans available for instant download with many different bonus offers.  The plans are detailed because they are written by a master woodworker.  He has taught many newbie woodworkers over the past 30 years how to build sheds and other woodworking projects.  He is skilled in the art of woodworking and put together a nice, large set of plans.  The plans are easy to read with step-by-step instructions.

It can be easy to get excited and overestimate your DIY abilities when you start a new project. The passion and excitement makes you want to dream big and get creative. But blindly following your imagination can be a step in the wrong direction. If you’re a newbie to DIY woodworking, then you’ll probably want to keep it simple. Otherwise you run the real risk of ending up with a sub par build or even having to rebuild it altogether.
Don Vandervort has developed his expertise for more than 30 years, as Building Editor for Sunset Books, Senior Editor at Home Magazine, author of more than 30 home improvement books, and writer of countless magazine articles. He appeared for 3 seasons on HGTV’s “The Fix,” and served as MSN’s home expert for several years. Don founded HomeTips in 1996.
Build your own shed and you'll instantly have increased space for your tools, a place to work on DIY projects and a way to keep your garage free of clutter. There are many shed plans online that show you how to build your own shed from scratch using wood. It may be easier, however, to use a kit to create a resin, metal or plastic shed instead. A storage shed kit contains all the materials you need including trim. This Home Depot project uses the Keter Stronghold Resin Shed Kit to show you how to build a shed from a kit. We also offer a large variety of other types of shed designs to choose from. Like most, this DIY shed requires tools like a power drill and step ladder to put it together, but assembly instructions will vary by kit. Make sure to follow the manufacturer's instructions carefully.
Once you’ve figured out what you need the shed for, it’s easy to go forward with planning. Keep in mind that sheds, no matter how small in their size, are not exactly the best projects for beginner woodworkers. Sheds are one of the most complex woodworking items to build. Some bigger sheds resemble houses so it’s not a surprise a shed is a project for a skillful hand.

· Gambrel styled shed — it is a very common type of shed. Its roof is highly steep and is four sided. This type of shed at some point resembles a hexagon. This type of shed is preferred as the shape of its roof makes the interior of the shed to be spacious hence creating more space where a lot of garden and outdoor tools can be stored. In this type of shed, one may have a workshop in the shed. They can even accommodate a car due to their large spaces.
The construction of a wood foundation is usually built using pressure-treated 2x6 lumbers. These parts are called the band on the ends and the joist in the middle of the band, spaced out 16-24 inches apart. The foundation frame will sit on top of pressure-treated 4x4 posts called skids. The skids will set on the cinder blocks or on top of gravel to prevent rot.
Ordering a prehung wood door like this from the lumberyard could cost as much as $1,000, but you can build one suitable for a shed at a fraction of the cost. We purchased clear pine at a home center and spent $120 for the boards. Photos 8 – 10 show how to build the door and mount it to a trim piece with hinges. The door consists of two layers of 3/4-in.-thick boards that overlap at the corners to add strength. Rip 1×6 boards to 4-1/2 in. on a table saw for the outside layer (Figure F).
Often referred to as the ebook expert, Bob Burnham's reviews are easily reachable everywhere – blogs, online publications and magazines. He was featured in prestigious publications and he even gained a few rewards for his own ebooks. While constantly releasing new work, his main focus is on unbiased reviews of modern ebooks while pursuing his career as a literature professor. Over the past years, his name was linked with a plethora of bestsellers that were successfully reviewed over the Internet. more
When people talk about the different types of shed available, what they should describe are the different types of roof available, since sheds only really differ by the type of roof they have. We provide shed plans for three types of roof: Gable, Lean-To and Hip. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-To sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-to sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-To sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage.
Level the ground (if necessary) and install deck piers along a grid to support the shed. The piers will allow you to string support beams beneath the floor of the shed. In the example design, the piers are spaced 6 feet (1.8 m) apart in one direction and 4 feet (1.2 m) apart in the other for a total grid area of 12 x 8 feet. This is convenient because once you lay supports along this grid, it will take exactly three standard 4- by 8-foot plywood sheets to cover it.[1]
Ordering a prehung wood door like this from the lumberyard could cost as much as $1,000, but you can build one suitable for a shed at a fraction of the cost. We purchased clear pine at a home center and spent $120 for the boards. Photos 8 – 10 show how to build the door and mount it to a trim piece with hinges. The door consists of two layers of 3/4-in.-thick boards that overlap at the corners to add strength. Rip 1×6 boards to 4-1/2 in. on a table saw for the outside layer (Figure F).
Once you’ve received the package and all it entails, you can begin creating your own outdoor shed whenever you feel ready. The only time you need to exert the effort is when you’ve begun construction. When you do decide to start, make sure that you have a decent amount of time as well as motivation to carry through the whole project. You don’t want to be left with an unfinished shed out in the yard, a constant reminder that you tried and failed.
• Purchase of two small sheds — it is dangerous to underspend just as it is to overspend. This is because you may underspend and the shed purchased may end up being of little use below your expectations. This will prompt you to build another shed and that will lead you to overspend. A shed may look simple on the outside but it is how you customize your shed that will determine the volume of goods your shed can hold. When building your shed it is important you identify each and every section of your shed, allocate the tools to each section and then modify the shed to hold each and every tool at its place. In that manner, you end up maximizing each and every space in your shed and also utilizing your shed to its maximum capability. It is also recommendable to have adequately spaced sheds where one can perform outdoor activities like car repairing in the shed when the weather is not favorable. Before starting your shed building, think of all its purposes and all the outdoor and semi-outdoor activities one could perform during unfavorable weather condition or any other related circumstances.
The Roofs of the sheds usually come in different shapes, sizes, and styles. One impeccable style among then is the Gambrel Roof, highly associated with barns and pole barns. The advantage of adopting this style is that these sheds can be used as high capacity storage spaces because of the steeper sides. Most of the recent homes have Gambler Roof Sheds because of the intricate beauty they bring to the home. Instead of bringing a standard roof, it won’t make much difference to bring a Gambrel Roof, given that you match the materials to your building.​
One last thing about shed sizes, it’s a good idea to always measure out the dimensions in your own garden before you invest any money. You can do this easily by using a couple of stakes and a string to measure out the space. That’s how the pros do it. Make sure that you leave enough room on all sides of the shed to help with rain drainage and prevent water damage.
• The ceiling is too low — these may tend to be one of the least concentrated on problems as they happen least when one expects. It is important to be aware of the low ceiling so as to save on your funds in putting a higher one. Ensure that each and every measurement is taken carefully and is also executed. The best way to determine the height of your shed is by scanning through the items you are planning to store there and use the tallest. As mentioned earlier, the installation of steep roofs might be risky but in the long run become an added advantage as they create more space inside the shed.
One look at everything you receive with this program and there’s no way you’ll ever opt to pay someone tons of money to do the exact steps that you have right in front of you. Ryan’s Shed Plans is the smart, affordable and easy way to build whatever it is that you want in your backyard. Whether it’s a rustic yard shed, a cottage shed, a garden shed, a gambrel barn or something else, you finally have all the (actual) steps needed to easily build it on your own. The program comes with way more than just a couple of project plans. Instead, it provides with you 12,000 different shed plans to choose from. So, if you want a shed with glass walls or a shed that’s perched on a porch, there’s a plan for it.
The last thing you want is to build a shed only to discover that it’s too small to hold your stuff, handle your hobby, or otherwise meet your needs. By the same token, you don’t want a shed that’s so large it overwhelms your property and looks ungainly behind your house. Choosing the wrong size shed is a common homeowner error, but LP Outdoor Building Solutions’ handy tool helps you get it just right. Check it out, and you’ll see that size does matter!
Proceeding with your shed requires smart planning. For starters, you may need a permit from your local zoning authority and/or homeowners’ association to build a new structure on your property; check with the proper authorities before you even invest in the materials. Plus, there may be rules that dictate how you may use your shed, or whether you’re allowed to wire it for electricity. Once you get the go-ahead to build, you’ll want reliable guidelines. For anyone inclined to DIY rather than buy a prebuilt shed, look over a selection of free LP Outdoor Building Solutions plans based on your choice of size and roof style. Each set of plans comes with extensive material and hardware lists, detailed construction information, and tried-and-true building tips.
The Dip treated sheds are made of components which are usually lowered into the tanks of preservatives even before the panels are assembled. This is a low-cost process that can be done simply, and also it encourages the manufacturers to use a wide variety of treatments making the shed types available for the DIYers. There are recognisable given that they usually come in golden brown due to the preservative dye that is added. Most of the manufacturers offer you around 10-year guarantee on dip treated sheds along with anti-rot treatment, but one has to recoat every year or the alternative year.​
Nail plywood sheeting to the joists to form the floor. If necessary, use H-clips in addition to nailing the sheets into place; these fit between two pieces of plywood and lock them together for additional structural strength. In the example design, two standard sheets of 4- by 8-foot plywood are used whole and a third is sawn in half and used to fill in the 4-foot difference on either end. Because of the spacing of the piers, support beams, and joists, no additional cuts or adjustments are necessary. Note that the pieces of plywood are intentionally misaligned so that the floor doesn’t have a single seam running across the whole thing, which would be a significant structural weakness.
If you have a router, use a hinge-mortising bit (or straight bit) to cut the hinge recesses (Photo 10). Otherwise, use a sharp chisel. Screw the hinges to the door and trim. To hang the door, line up a temporary 2×4 with the bottom of the siding and screw it to the wall. Then rest the door on the 2×4 and drive 3-in. screws through the trim into the framing to hold the door in place (Photo 11). Finish the door installation by adding the top and side trim pieces.
Ryan had a difficult time building his own first shed. Wrong material, wrong measures, wrong techniques, all of them didn’t help in making the shed any quicker. It took him 6 months to complete his first shed project, and at the end of it he was worn out and exhausted. Even after spending a lot of time reading and purchasing woodworking books, blueprints, nothing seemed to work. Most of the shed plans he bought lacked vital information which left him with more questions than answers. That is when he decided to leave it all aside and build his own shed plans. That was the beginning of his work towards building his master collection of shed plans.
Build your own shed and you'll instantly have increased space for your tools, a place to work on DIY projects and a way to keep your garage free of clutter. There are many shed plans online that show you how to build your own shed from scratch using wood. It may be easier, however, to use a kit to create a resin, metal or plastic shed instead. A storage shed kit contains all the materials you need including trim. This Home Depot project uses the Keter Stronghold Resin Shed Kit to show you how to build a shed from a kit. We also offer a large variety of other types of shed designs to choose from. Like most, this DIY shed requires tools like a power drill and step ladder to put it together, but assembly instructions will vary by kit. Make sure to follow the manufacturer's instructions carefully.
This is nothing but a pyramid scheme in disguise. Don't spend the first $37.00, they lead you to believe that you are getting discs and actual plans until you pay $37.00, then they tell you that you have to download everything but at an additional price. I'm calling the Fraud Department at the Texas State Attorney Generals office and reporting them.
A garden shed can be strictly functional, but it can also be a decorative focal point around which you design your garden or yard. These plans will help you build a basic shed, but don’t stop there! To customize your shed, you could create a combination toolshed and greenhouse, put a martin house on top, or use part of the shed for a chicken coop or rabbit hutch. If you’re feeling even more adventurous, you could create a living roof of moss or succulent plants.
We now need to create a base that we can nail the frames for the walls into.  We did this with four 2x8's and some bent i-bolts along with a lot of mortar.  The basic process was that we bent the bottoms of the i-bolts after heating them with a blow torch, and then anchored these in some of the holes in the cinderblocks with a lot of mortar.  Then we drilled holes in the 2x8's where the i-bolts were and put these on top and screwed them in.  The frames can now be solidly attached to the base with the framing hammer.
• Wastage of space — this is one of the greatest mistakes one can make. It is mostly caused by poor construction planning. You may such a mistake also by taking measurements poorly. You should consider all the activities and purposes that you will use your shed for before starting the construction. In that manner, you will be able to come up with a shed design that will suit its purpose and your wishes. One may also consider building a double floor shed to save on your compound space. You wouldn’t want to deny your kids their playing ground! You may also want to construct a different structure in the future then you get hindered due to the little space left or unless you would have to dig deeper into your pockets to modify your shed.
Sheds have become multipurpose, must-have buildings that are competing with pergolas and gazebos as your next backyard project. Pictures on social media only grab people's desires more. Before going any further, do your research. Figure out what you need it for and why, and whether you will build the shed yourself, or hire a pro. Check with your local planning department to comply with codes and guidelines. Determine if the shed will mirror the architectural features of your home--always a good idea. Assess your budget, materials needed, and the time it will take to complete the project.

The construction of a wood foundation is usually built using pressure-treated 2x6 lumbers. These parts are called the band on the ends and the joist in the middle of the band, spaced out 16-24 inches apart. The foundation frame will sit on top of pressure-treated 4x4 posts called skids. The skids will set on the cinder blocks or on top of gravel to prevent rot.

One last thing about shed sizes, it’s a good idea to always measure out the dimensions in your own garden before you invest any money. You can do this easily by using a couple of stakes and a string to measure out the space. That’s how the pros do it. Make sure that you leave enough room on all sides of the shed to help with rain drainage and prevent water damage.
×