If you don’t plan to have electricity running through your shed, this is the shed building tip you will want to listen to most. Windows easily brighten up a shed so you don’t have to hunt around for a flashlight or a lantern if you’re old school, every time you need to grab something from your shed. But…don’t go nuts and install a ton of windows or you will be giving up valuable space to hang tools or shelves.

Building something yourself, especially something as big as a shed, is always rewarding, but not only will it feel good to have a self-made beauty in your backyard, it’s times lower in cost than buying a shed. In fact, building a small shed can cost as little as $100! That’s a pennysaver! And well, all proper DIY wood projects should be, ain’t that right?
I can’t believe the amount of plans your able to offer for the price. I’m planning on building a summerhouse at the bottom of the garden next month, and I have a rough idea of how I’d like it to look. What I do need is some help with plans and an idea of how much it’s going to cost. Looks like that’s all covered now! With 12000 projects included, I’d put money on it that there’ll be at least one design close to the one in my head. In fact I’m going to. Seams like a sure bet to me. Cheers Jack!
Are you one of those people who love woodworking and seek joy out of it? If yes, well you might already know that every woodworking project requires a certain amount of time and effort to be invested in it. In some cases, it’s almost the same as the construction projects, and many people say that building a wooden shed is synonymous to building a brick wall. Even when it’s easy and simple, you should have adequate knowledge to successfully implement the design plan.
Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.
If you're excited to start browsing Ryan's shed designs, you're right where I was shortly after finding Ryan Shed Plans. If you can dedicate some time to putting your own shed together and don't mind purchasing the materials from a local store or ordering them online as needed, you will appreciate the thorough instructions provided with each of Ryan's plans. There are so many options that you should have no problem finding a design that fits your needs, and you will have tons of inspiration to fuel future projects as well.
For example, the last three sheds I built were trimmed with white PVC trim boards instead of painted cedar 1 x 4s. This new plastic lumber, which I used for the rake, fascia, frieze and corner boards, is impervious to bugs, warping, splitting or decay, and it never needs painting. Other low-maintenance options include: vinyl or aluminum windows, faux-slate roof shingles, fiberglass or steel doors, composite decking for steps, and fiber-cement siding. (I don't usually recommend aluminum or vinyl siding for sheds; neither material is rugged enough to survive the inevitable beating outbuildings take.)
To be sure, the whole permitting process can be a bit intimidating. And, if I'm being honest here, I've never been comfortable dealing with the city and all their codes - seems they're always moving the line on me. But, I always make it a point to be friendly with the Building Inspector. He's there to help and can be a fountain of information, when building your wood shed.
If you buy heavy galvanized hardware designed for farm buildings for your shed, it’s overkill. Buy heavy-duty closet door hardware instead. It’s not really meant for outdoor use, but when it’s protected by an overhang, it holds up well. And if the roller bearings get corroded, it’s simple to replace the entire hanger mechanism. Check out Johnson Hardware’s 111 track and 1025 ball-bearing hangers.
Figure A (above) and Figure E show how to build a shed and the exterior trim details. Start by mounting the brackets. Line up the outside edges of the lower brackets with the face of the siding, push them tight to the soffit and screw them to the wall. Center the top bracket on the peak and push it tight to the soffit. Starting with the pieces that go under the brackets, wrap the corners with the corner board. Overlap the front corner board onto the side corner board (Figure E).
After the concrete is all ready, the sole plates are then joined together with the anchor plates which protrude out of the foundation. Use the carpenter’s pencil and measuring tape to mark about one and a half inches from the board end continually every sixteen inches till the further end. These marks guide where the studs will be placed. Mark where the anchor and the mudsill meet up with a different marker from the one used initially. The studs are then taken and galvanized nails are driven through the marked areas into the center of the board until they reach the stud bottom. The studs should be secured to the baseboard.
Ryan Henderson seems pretty straightforward and confident about his product. There are no outrageous claims that have been made, like building a shed in 15 minutes, and all the expectations on the website are pretty realistic. You won’t feel the need to question the product, as the website is very detailed, making it seem like they only want their consumers to be well-educated on the sheds they decide to make.
You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls. Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center (Photo 1). You’ll use this line to make sure the angled top plates meet in the center. 

Stand the back wall. Then align the corner of the side and back walls and nail them together. With a helper on the outside of the shed to push if necessary, line up the inside edge of the bottom plate with the chalk line and nail it to the platform. Continue around the building, standing the opposite end wall and finally the front wall. Nail the corners together, making sure that the top plates of adjoining walls are flush with each other.
For strength, plan to build the front and back layers so the corners overlap each other. Then, to accommodate inset panels, make the front pieces a little wider to create a lip for the panels to rest against. Use plywood or tongue-and-groove boards for the panels, and hold them in with stops nailed on the back. You can assemble the two frames with pocket screws before gluing and screwing them together, but it’s not necessary. After the glue dries, plane or sand the edges to hide the fact that there are two layers.
• Wastage of space — this is one of the greatest mistakes one can make. It is mostly caused by poor construction planning. You may such a mistake also by taking measurements poorly. You should consider all the activities and purposes that you will use your shed for before starting the construction. In that manner, you will be able to come up with a shed design that will suit its purpose and your wishes. One may also consider building a double floor shed to save on your compound space. You wouldn’t want to deny your kids their playing ground! You may also want to construct a different structure in the future then you get hindered due to the little space left or unless you would have to dig deeper into your pockets to modify your shed.
×