I'm on my third Central vac over a period of 15 years. All have been Kenmore. I have a 2500 sq ft home, I vacuum every day. Aways burn out the power head, hence why I am shopping again. I have flooring & carpet throughout. I want lots of power& a hose that doesn't kink (what a pain that has become) I refuse to spend more than $700, as they just don't last. Any suggestions? I've been checking out Electrolux........
The walls of the foundation have been created and the electrical is all set, now all that needs to be done is to fill the gaping hole in between them with limestone agrigate.  We also threw in some concrete paving stones that we had lying around because we don't plan on using them and we had already tried to give them away.  After the limestone is in place tamp it down by jumping on it and keep filling up any places that are no longer level.  After the entire base is filled with as much limestone as you can fit put a sprinkler on to soak it and set it for the next hour or so.  You may need to add a bit more limestone after this is done as well.
Proceeding with your shed requires smart planning. For starters, you may need a permit from your local zoning authority and/or homeowners’ association to build a new structure on your property; check with the proper authorities before you even invest in the materials. Plus, there may be rules that dictate how you may use your shed, or whether you’re allowed to wire it for electricity. Once you get the go-ahead to build, you’ll want reliable guidelines. For anyone inclined to DIY rather than buy a prebuilt shed, look over a selection of free LP Outdoor Building Solutions plans based on your choice of size and roof style. Each set of plans comes with extensive material and hardware lists, detailed construction information, and tried-and-true building tips.
Then, you will need to install a series of floor joists across the entire length of the support beams; these will need to be the same length as the distance between the two rim joints so that they’ll fit between them. In the example design, the floor joists are all separated by 14.5-inch gaps except for the outermost two, which are 13 3⁄4 inches (34.9 cm) from their immediate neighbors; this is to allow a standard piece of plywood to line up with the outermost edge of the outermost joist but only cover half of an interior joist, allowing its neighbor to cover the other half so that both can be supported properly.[3]
Now, if the only need for the present is a shed that’s large, consider purchasing garden shed plans blueprints for small sheds at the same time. You might need small storage spaces in the future or there are items that need to be stored separately. For example, for storing dangerous things like pesticides, gasoline and herbicides, the most appropriate sheds are small plastic sheds.

The plan features not only a cutting list and project diagram. There are also clear instructions starting from building the base and ending with installing the windows and doing the trims. Once you’ve built a small shed like this, you’ll have enough experience to build a bigger one that fits all the garden equipment as well. A tiny shed like this though is a necessary item for every home!
The sheds available can be distinguished easily as they come in pale green that eventually fades into silvery grey. The Pressure treated sheds are relatively a bit costlier than the DIP treated sheds and the advantage of using them is that they don’t need further preservative treatment and can serve the whole during the entire ten years saving a lot of time and money.​
Also square the frame by making sure diagonal measurements from opposite corners are equal. Then tack one corner to hold it square. Finally, nail the soffit to the roof frame with 6d galvanized box nails. We used 12-in.-wide fiber cement siding for soffit material. Mount an inexpensive carbide blade on your circular saw to cut the fiber cement. Set the roof panel aside and build the other half of the roof using the same techniques.

Working from ladders is more dangerous than working from scaffolding. Plus, having to constantly move ladders around is time consuming. When you get to the roof construction, consider renting a set of scaffolding with wheels. You’ll be amazed at how much easier it is to have a stable platform to work from and to set your tools and materials on. You can rent a 5-ft.-tall section of scaffold with three planks and wheels for about $110 per week.


I have recently purchased a house with an older roof that needs to be restored soon. So, I am trying to decide on I should go with a metal roof other than shingles. If I install metal roofing over solid decking such as OSB or plywood, integrate with a properly insulated garret, there is very little noise difference compared to standard asphalt shingles. I have briefly read benefits and drawbacks of Metal roofing but as I listed before I should go to metal roofing and hiring a roofing contractor no matter its expensive or noisy anyhow, Your article has cleared a lot of misinterpretation I’ve had before.
My advice... Don't do-it-all-yourself. Novice and pro alike can benefit from each other in DIY. You might have the shed location leveled by a landscaper; get a referral to outsource the shed's foundation to a building subcontractor; you can even have the roof's trusses made by a local truss company and the shingles installed by a handyman or roofer.
Nothing dresses up a shed like brackets. They’re the ultimate low-effort, high-impact feature. In some cases they also provide extra support for your gable-end overhang. Depending on the design, you can build brackets from 4x4s or by laminating 2-by boards. Make a full-scale drawing to work out the details. Then build the brackets and attach them to the shed. Install the brackets tight to the underside of the overhang, and then notch the fascia board to fit over them.
My Shed Plans just might be every do-it-yourself junkie’s dream product. Ryan Henderson, the creator of My Shed Plans, has been building one-of-a-kind outdoor sheds for more than 20 years. If you believe his story, he has unselfishly decided to share his love of woodworking and carpentry through his guides which will enable the everyman who does not have handyman experience to build their very own outdoor shed. Can it be true?
Just like other such programs available in the market, even this one offers both benefits and drawbacks. Before you purchase the program, it is important to consider these things. According to most reviews and customers, the benefits of this program easily outweigh the drawbacks. However, it is very important to analyze these things to ensure you make an informed decision. This will also make sure that the program meets your specific woodworking needs and requirements.
Once you’ve received the package and all it entails, you can begin creating your own outdoor shed whenever you feel ready. The only time you need to exert the effort is when you’ve begun construction. When you do decide to start, make sure that you have a decent amount of time as well as motivation to carry through the whole project. You don’t want to be left with an unfinished shed out in the yard, a constant reminder that you tried and failed. 

Thanks for sharing such detailed plans Seamster. I'm hoping to build a very small lean-to tool shed (2.5X4.5' base) for my very small yard and this has given me a lot of insight. Currently, theor the table and mitre saws I inherited are stored in our spare bedroom... eventual nursery room. I want to get them into their own space outdoors sooner than later. Here in North Carolina with the humid summers I think it would be best to add some housewrap to the walls to help protect the tools. I also have a situation where the back wall will only be 4-6" off the house so need to construct/panel my walls before erecting them. Do you know if it's reasonable to panel then wrap each wall frame, side it and then finally erect and fasten? Would be very grateful for your thoughts!
My Shed Plans provides you with numerous benefits, such as easy to understand language, ease of access, properly organized plans and more. Besides these benefits, the program also contains a wide range of features to make everything easier for you. These features and benefits make this program stand apart from the competition. This is a unique program easily available in the market. The program offers a lot to people who want a shed in their backyard or garden. Here are some key features of the program that make it an exceptional choice :

High-quality materials may cost a bit more, but they’ll save you time, trouble, and money in the long run. The chart here shows how LP® SmartSide® Panels compare with untreated plywood, vinyl, and galvanized metal. No wonder so many pros recommend sheds made with beautiful, durable LP products! If you want your shed to resist splitting, cracking, decay, and termite damage while duplicating the good looks of rich, real cedar, choose LP SmartSide® products.
When choosing where to build your shed, choose a flat dry spot on your property. This will make it easier to excavate and level it out, and ensure that you build on a dry surface. Avoid building your shed in a low lying area that is prone to water collection or you’ll find your shed flooded after a big rain. Too much water means rotting wood, blistering paint and rusty hinges and none of that will highlight how hard you worked to build this shed.
Door placement is also important. You often see doors placed on the gable end of the building, which looks nice, but makes it virtually impossible to reach items stored at the rear of the shed. A better alternative is to put the door on the long side wall, so that you'll be able to access items to the right, left and back. Another option is to install doors on both gable-end walls, so that you'll be able to easily reach items from either end of the shed.
@diy-plan: Thank-You for your best wishes on the Isacc, believe we always lose sleep when one is on the way. Your advice on not buying factory kit sheds I am 100% in agreement with, they are poor quality lumber, never pressured treated, steldom last more than ten years, here they are lucky to make it six years. I was asked to put one together by a friend after her son bought it for her as a gift, I almost had to rebuild it and when I was finished I thought what an ugly building. Five years later it had termites. When a shed is built on a wood base the base must be anchered into the earth, I have seen sheds flipped upside down after a storm when they are not anchored. I built a shed for a workshop a few years ago to build custom canoes in it, to make it storm ready I used OSB under the siding, then cross braced the studs, insulated it, then covered the studs on the inside with 5/8 inch plywood. The windows have storm shutters that I built for them, if this building fails in a storm I hope I am near the Canadian border.
Are you one of those people who love woodworking and seek joy out of it? If yes, well you might already know that every woodworking project requires a certain amount of time and effort to be invested in it. In some cases, it’s almost the same as the construction projects, and many people say that building a wooden shed is synonymous to building a brick wall. Even when it’s easy and simple, you should have adequate knowledge to successfully implement the design plan.
When people talk about the different types of shed available, what they should describe are the different types of roof available, since sheds only really differ by the type of roof they have. We provide shed plans for three types of roof: Gable, Lean-To and Hip. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-To sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-to sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-To sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage.
For example, the last three sheds I built were trimmed with white PVC trim boards instead of painted cedar 1 x 4s. This new plastic lumber, which I used for the rake, fascia, frieze and corner boards, is impervious to bugs, warping, splitting or decay, and it never needs painting. Other low-maintenance options include: vinyl or aluminum windows, faux-slate roof shingles, fiberglass or steel doors, composite decking for steps, and fiber-cement siding. (I don't usually recommend aluminum or vinyl siding for sheds; neither material is rugged enough to survive the inevitable beating outbuildings take.)
I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks
· Gable shed — they are also common due to their stylish two-faced roof that meets at the center forming a peak. Their roof shapes are conducive as they provide adequate space, but not as much as the gambrel styled sheds. They provide adequate spaces for storage of garden tools. They also accommodate larger items as motorcycles. The property that makes these sheds become common is their stylish shape that blends in well with any compound with a house of any design.
The advertising was incredibly misleading. The early indications (at least via ********) are that you can purchase downloadable shed plans. Further claims are made that **** ********* is offering something unique in the detail and instruction, such that someone with no building experience could purchase material, fabricate, and build these sheds. First, that is not at all the case. most of these "plans" are only one-page shots. Second, most of the plans couldn't be build even by someone who is in construction or familiar with building. This stops just short of being a SCAM. At the very least, it's extremely misleading. **** ********* should be ashamed of himself.

It can be easy to get excited and overestimate your DIY abilities when you start a new project. The passion and excitement makes you want to dream big and get creative. But blindly following your imagination can be a step in the wrong direction. If you’re a newbie to DIY woodworking, then you’ll probably want to keep it simple. Otherwise you run the real risk of ending up with a sub par build or even having to rebuild it altogether.
If you plan to paint your shed, natural wood siding isn’t necessary. You can buy sheets of OSB (oriented strand board) siding at a fraction of the cost of real plywood, and it’ll probably last longer too. LP SmartSide panel is one brand. You can buy plain, grooved or stucco-like panels in several thicknesses and sizes. Ask at your local lumberyard to see what’s available.

Apparently, most guides provide you with the same old information that doesn’t offer any benefits to a gardening or DIY enthusiast. Fortunately, you can benefit from programs like My Shed Plans. This exceptional program is easily available on the internet at an affordable price, and helps you learn everything about building a shed in your garden or backyard.
These plans are for saltbox roof style sheds.  They are built with trusses that you build.  These sheds are perfect for general storage, garden sheds, tool sheds, potting sheds, playhouses and more.  This shed in my opinion, if you are wanting to build a shed for gardening, this is the one.  It has lots of charm and character with it's desirable design.
Don Vandervort has developed his expertise for more than 30 years, as Building Editor for Sunset Books, Senior Editor at Home Magazine, author of more than 30 home improvement books, and writer of countless magazine articles. He appeared for 3 seasons on HGTV’s “The Fix,” and served as MSN’s home expert for several years. Don founded HomeTips in 1996.
Run! Do not walk away from this product! Total scam! The Ryan Shed Plans product promises 12,000 different do it yourself shed building plans. Instead what you get is a whole bunch of disconnected sketches, drawings, And partial blueprints that he has photo copied from hundreds of unrelated sources. I personally have several years of carpentry, homebuilding, and woodworking experience So I assumed that even if these so-called “shed building plans” we’re light on specific details I’d still be able to use them. WRONG! You will find that 99% of the“Plans“ are completely useless for the purpose of building a backyard shed. After an hour of grinding through the files included in that on my download, I did happen upon a singly reasonably complete building plan for a modest shed which included detail dimensions, material list, and the sorts of things needed to actually build a shed. Doing a little more research, I later found where this particular we’ll Drawn to plan had been ripped off from another legitimate Shed building website. Shame on you RyanShedPlans for marketing such a terrible, useless product. Judging from your online sales pitch you are clearly a gifted marketer. If you spent as much time developing a database of legitimate, usable shed plans as you did putting together your totally fraudulent marketing material, you would have an incredible product worth much much more then you’re charging. But I guess you I already know that.
×