The trick for learning how to build a storage shed is to stretch the line across a scrap of wood at each end so there’s a space between the line and the part you’re straightening. On a wall, for example, tack small scraps of 1/2-in. plywood at each end of the top plate and stretch a line very tightly over the plywood. Then use a third scrap as a gauge to check the distance between the line and the lumber. Use braces or whatever is needed to adjust the top plate until the gauge just fits. Now your top plate will be perfectly straight.
Working from ladders is more dangerous than working from scaffolding. Plus, having to constantly move ladders around is time consuming. When you get to the roof construction, consider renting a set of scaffolding with wheels. You’ll be amazed at how much easier it is to have a stable platform to work from and to set your tools and materials on. You can rent a 5-ft.-tall section of scaffold with three planks and wheels for about $110 per week.
I like to use the hip roof design, it is pleasing to the eye, it is the best roof for high winds, certainlly a good idea with the hurricanes and tropical storms found in South Florida. I always build my sheds on a raised concrete slab for stability, I also use double hurricane ties. All studs and rafters are pressure treated because of the area's termite problems. I always anchor the shed to the concrete slab with expoy bolts. I never use T11 siding it does not hold up well in a subtropical climate. I use OSB under the siding and I often cross brace. I prefer a metal roof screwed down not nailed using water gasket screws. I generally use ridge vents or a wind turbine to help cool the shed and I also use Bahama shutters for the same reason. I build with rafters not trusses so I can keep the celling open to also cool the shed. This makes the shed expensive but after twenty years of use one of my oldest sheds which received proper up keep is still perfect. So which is cheaper one shed for life or one after every major windstorm? I know the answer because I had one shed stand up to a huricane!
• Time underestimation — people normally underestimate the time taken to build any given structure. It is a normal occurrence when building delays, the delays may be caused by issues as inadequate tools and climatic changes that would not allow outdoor activities as the building. Building any kind of structure may take longer than expected. It is therefore important to do things at a fast rate to reduce the number of delays that one has to encounter and also reduce frustration brought about by delays. Completion of construction is also advantageous as one gets to start using the structure sooner than expected which to some extents save on your finances.

Before you exert effort in finding the woodworking company with the best shed plans, it is very important that you determine first the right type of shed that will suit your purpose. Now, aside from the purpose, there are other things to consider like the area where to put the shed (shed plans 12×16), the things that you will store in the shed, the appropriate building materials to use, the kind of environment or the weather in your place, and of course, safety issues. Will the shed be also used for the family’s recreational activities, or for workshops and meetings, or for some business ventures? Purchase shed plans because they can help in answering some of our important questions about this matter.
The framing is the most important part of the above-ground structure because it stiffens up the plywood boards and supports the roof.  You will need a lot of 2x4's, and a way to attach them.  We used this as an excuse to buy some new air hammers from canadian tire.  We were able to get the lumber for the entire project delivered by a company called Tamrack Lumber.  They brought out a truck and dropped off all the supplies.  For the roofing you will need little plates with groups of nails sticking out of them which I believe are called joist plates.  These are used on the angles to keep them from shifting.  The last thing you will need is a way to cut all of the 2x4's.  To do this we borrowed a very nice miter saw from a friend for a few days.  It is much easier if the cutting tool can cut on angles, otherwise you will be left to improvise when cutting the peices for the roof.
We’ve simplified the door-hanging process by mounting the door to a 1-1/2-in.-thick trim piece and then screwing the trim to the wall. An easy way to mark and cut matching hinge recesses in both the door and the trim is to clamp the trim alongside the door, making sure it extends 1/8 in. beyond the top of the door. Then mark the hinge cutout on both the door and the trim at the same time.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Copyright © 2019. All Rights Reserved. 3DSHEDPLANS™ is officially registered and protected trademark in the United States. Owned & operated by Netholics Media, LLC. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law. For permission or any other requests, please get in touch with us using the contact form provided. Use of this website constitutes acceptance of the 3DSHEDPLANS.COM’s User Terms and Privacy policy.
In a perfect world, all of the studs would be straight, but since they aren’t, make sure to pick the best ones to use at corners and at door and window openings. Sight down the length of the studs and set aside the ones that are perfectly straight. While you’re at it, also set aside studs that are really crooked. You can cut these up to use as cripples or blocking. You may find other uses for short pieces later on.
The walls of the foundation have been created and the electrical is all set, now all that needs to be done is to fill the gaping hole in between them with limestone agrigate.  We also threw in some concrete paving stones that we had lying around because we don't plan on using them and we had already tried to give them away.  After the limestone is in place tamp it down by jumping on it and keep filling up any places that are no longer level.  After the entire base is filled with as much limestone as you can fit put a sprinkler on to soak it and set it for the next hour or so.  You may need to add a bit more limestone after this is done as well.
×