When choosing where to build your shed, choose a flat dry spot on your property. This will make it easier to excavate and level it out, and ensure that you build on a dry surface. Avoid building your shed in a low lying area that is prone to water collection or you’ll find your shed flooded after a big rain. Too much water means rotting wood, blistering paint and rusty hinges and none of that will highlight how hard you worked to build this shed.
High-quality materials may cost a bit more, but they’ll save you time, trouble, and money in the long run. The chart here shows how LP® SmartSide® Panels compare with untreated plywood, vinyl, and galvanized metal. No wonder so many pros recommend sheds made with beautiful, durable LP products! If you want your shed to resist splitting, cracking, decay, and termite damage while duplicating the good looks of rich, real cedar, choose LP SmartSide® products.
Then, you will need to install a series of floor joists across the entire length of the support beams; these will need to be the same length as the distance between the two rim joints so that they’ll fit between them. In the example design, the floor joists are all separated by 14.5-inch gaps except for the outermost two, which are 13 3⁄4 inches (34.9 cm) from their immediate neighbors; this is to allow a standard piece of plywood to line up with the outermost edge of the outermost joist but only cover half of an interior joist, allowing its neighbor to cover the other half so that both can be supported properly.[3]

We decided to construct the foundation of our shed out of cinderblocks.  This will help keep out any rodents, and doesn't risk harming the trees beside the shed.  In order to lay a good foundation, we first had to level out the ground. We didn't need to level out the middle of the structure's base because that was later filled with limestone screening.  We made channels for the cinderblocks with spades and a pickaxe, and made sure to create a channel for the electrical as well.  The electricity comes from our house, which is about 10 feet away from where the shed stands.

The construction of a wood foundation is usually built using pressure-treated 2x6 lumbers. These parts are called the band on the ends and the joist in the middle of the band, spaced out 16-24 inches apart. The foundation frame will sit on top of pressure-treated 4x4 posts called skids. The skids will set on the cinder blocks or on top of gravel to prevent rot.


Because the shed is designed to abut to another structure, the foundation need only be pressure-treated skids, the roof pitched in only one direction to shed water, and the back wall sheathed with 1/2-inch CDX plywood, which withstands indirect exposure to moisture. See Anatomy of an Outdoor Shed or Playhouse for more about typical shed construction. 

Listen, about the My Shed Plans Scam… all you can say is haters are gonna hate. There are way too many people on the web going about trying to ruin things for others. It probably makes them feel bigger than the basement of their parents’ house allows. In regards to your My Shed Plans product, it looks like a great deal. 12,000 shed plans, all in one package? Seriously, is there any plan that’s missing?
Once you’ve figured out what you need the shed for, it’s easy to go forward with planning. Keep in mind that sheds, no matter how small in their size, are not exactly the best projects for beginner woodworkers. Sheds are one of the most complex woodworking items to build. Some bigger sheds resemble houses so it’s not a surprise a shed is a project for a skillful hand.
Since outdoor space is limited in a big city, everyone knows you must make smart use of vertical real estate. For a greenhouse/shed in San Francisco's Bernal Heights, Step 3 Studio designed in an open-framework structure that provides shelter for a garden shed that stores potting materials and plants on the ground floor. A steel staircase was built on site, which leads to a second level surfaced in steel grid mesh. The higher elevation is the perfect spot for container plants that require more sun. It's also a nice place to hang out and enjoy views of the city, day or night.
We now need to create a base that we can nail the frames for the walls into.  We did this with four 2x8's and some bent i-bolts along with a lot of mortar.  The basic process was that we bent the bottoms of the i-bolts after heating them with a blow torch, and then anchored these in some of the holes in the cinderblocks with a lot of mortar.  Then we drilled holes in the 2x8's where the i-bolts were and put these on top and screwed them in.  The frames can now be solidly attached to the base with the framing hammer.
Now we can actually start building!  Before you start putting down cinderblocks, lay limestone screening down in all of the channels and run and burry your electrical.  Make sure that your electrical wires are clearly marked (we used caution tape) so that nobody digs them up accidentally in the future.  Once your all set, you can start putting down some cinderblocks.  You may need to break some cinderblocks in half, and this is easily done with a chisel, a hammer, and a bit of time.  Tip:  Set Rebar posts in each corner and tie strings across to help you keep the walls straight.  You need to check every single block for level, especially on this layer as the base of the foundation will affect the rest of the foundation and in turn affect the main structure.
Apart from being a space to keep your garden equipment and tools safe and dry under the roof, there are numbers of other possibilities how to use our timber structures and DIY shed plans. You can create a kids play area, a detached study, an additional storage space, tiny studio or a little secret relaxing spot. No matter what purpose our shed plans for sale will have in your life, they will always be a lovely addition to your home. Also the shed plans prices are very friendly.
This site is owned and operated by Sinova Enterprises LLC. Sinova Enterprises LLC is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Sinova Enterprises LLC also participates in affiliate programs  and is compensated for referring traffic and business to these companies.

Search the hashtag #vintagetrailers on Instagram and you'll discover some 80,000 images of big, small, and mid-sized aluminum travel trailers from roughly the 1950s to 1970s. You might find gleaming silver Airstreams at a lodging rental in Joshua Tree or parked temporarily at a campground near Yellowstone. One trend that hasn't lost steam is the backyard she-shed trailer escape, a dolled-up adult playhouse where women--or men--can escape for alone time or hang out with friends and a bottle or two of wine.  There's even a Vintage Trailer Magazine for enthusiasts. This vintage Aljo trailer rests in the backyard of a house in Pasadena, California.

• Wastage of space — this is one of the greatest mistakes one can make. It is mostly caused by poor construction planning. You may such a mistake also by taking measurements poorly. You should consider all the activities and purposes that you will use your shed for before starting the construction. In that manner, you will be able to come up with a shed design that will suit its purpose and your wishes. One may also consider building a double floor shed to save on your compound space. You wouldn’t want to deny your kids their playing ground! You may also want to construct a different structure in the future then you get hindered due to the little space left or unless you would have to dig deeper into your pockets to modify your shed.

After laying out the 12 blocks, use a straight 2 x 4 and a 4-ft. level to ensure that all the blocks are level. Shim up any low blocks with strips of asphalt roofing, cedar shingles or 2-in.-thick concrete patio block. Next, form each front and rear band joist by nailing a 2 x 6 to a 2 x 8 mudsill. Set the mudsills on top of the blocks running across the front and rear of the shed. Cut a third 2 x 8 mudsill to fit along the tops of the center row of foundation blocks.
Omit the bird’s-mouth from four rafters and use these on the ends. Cut the 2x4s for the ridge and subfascia to length and mark the rafter positions on them. Line up the rafters with the marks and nail through the ridge and subfascia with 16d nails to secure them. When the roof frame is complete, line up the subfascia with the chalk line on the platform and tack it in three or four places with toe screws to hold the frame straight while you install the soffit.
These days, it is not very easy to translate your wooden shed plans into a standard written format without losing any valuable information. In order to learn how to build high quality wooden sheds, it is important to consult an expert. However, consulting an expert may not be viable for every individual. In addition to this, the internet provides you with extensive information about a wide range of subjects.
Do not make the mistake of not building your own shed because you have never done it before. With the right shed plans you will get the same results the experts get. Begin by choosing plans you feel comfortable with and know you can follow along. Simply follow the steps provided, measure correctly, and in no time you will construct your own shed. Study the building guide to get familiar with all the steps and to get to know the names of all the parts.
For those who don’t quite believe in My Shed Plans, they offer a 60 day trial. If within those 60 days, you feel like the product hasn’t lived up to its hype, you may return it and receive a full refund. A decent outdoor shed can be built in a week or two depending on your schedule, and the amount of time you have to build it. Therefore, 60 days is enough for you to test out the product and see what you come up with. If you have a shed worthy of showing off to your buddies, or gal pals, then keep it. If you have a heap of materials in a pile that resembles something Homer Simpson might have created, then return it. No big deal.

Also square the frame by making sure diagonal measurements from opposite corners are equal. Then tack one corner to hold it square. Finally, nail the soffit to the roof frame with 6d galvanized box nails. We used 12-in.-wide fiber cement siding for soffit material. Mount an inexpensive carbide blade on your circular saw to cut the fiber cement. Set the roof panel aside and build the other half of the roof using the same techniques.


Made from durable blow molded resin, this Alpine shed from Suncast comes complete with 14 windows with delightful contrast trim. The double doors are built with articulating metal hardware so they’re robust and durable. The floor is reinforced for the ultimate sturdy foundation. Extra roof support is provided by the metal trusses and ridge beaming. This shed is perfect when you’re looking for something that is built tough, and stands out beyond the more flimsy and cheap designs that you find on the market. It is large enough to stow everything that you need and keep all items clean, safe, and secure. The outer appearance of this shed makes it perfect for those who want an attractive external design that doesn’t stick out like a sore thumb in your yard. All in all, customer reviews across the board are quite positive for this shed, and it makes a great addition to anyone’s home.
The Glidetop Slide Lid shed from Suncast features an ultra tough resin construction that makes it one of the most long lasting and easy to maintain sheds on the market. The gliding lid makes walk-in access quite easy, and the reinforced floor makes the shed perfect for tractor support. Perfect for storing all kinds of things, like patio furniture, mowers, bikes, and wheelbarrows. It’s easy to lock the shed and protect everything inside, year-round. The extra secure roof on the Suncast is what makes it really stand apart from its competition. It doesn’t stand too tall, so if you need to keep your shed below fence level then this is the ideal model for you. Suncast is one of the leaders in durable, affordable sheds, and this model is a great choice if you’re looking to save a little money and still have a storage unit that is going to last you for years to come. The assembly of the Suncast is incredibly easy and requires minimal tools to set-up.
Does this all sound very promising and great, but you still have your doubts about not being certain how to build a shed and if you are brave enough to buy the shed blueprints? We can help here as well with our newest book How to build a tiny house. This step by step guide with illustration and photographs provides useful information and in-depth instructions regarding every area of timber frame construction and its foundations, walls, roof and floor. You can order it anytime on our website, in a print version or as ebook.
Because the shed is designed to abut to another structure, the foundation need only be pressure-treated skids, the roof pitched in only one direction to shed water, and the back wall sheathed with 1/2-inch CDX plywood, which withstands indirect exposure to moisture. See Anatomy of an Outdoor Shed or Playhouse for more about typical shed construction.
The last thing you want is to build a shed only to discover that it’s too small to hold your stuff, handle your hobby, or otherwise meet your needs. By the same token, you don’t want a shed that’s so large it overwhelms your property and looks ungainly behind your house. Choosing the wrong size shed is a common homeowner error, but LP Outdoor Building Solutions’ handy tool helps you get it just right. Check it out, and you’ll see that size does matter!
By searching online you can find some free shed plans that are decent. Most often though these plans will be geared towards more experienced builders and they will not be very detailed. If you are a first time builder look for plans you can understand, even if it means paying a little. Use plans that contain a material list and plenty of details if this is your first time. Most free plans available are not as detailed with the building steps, so free is not always a good idea. If you go to the top of this page I have provided a list of some of the best plans from reputable websites.
A shed-like companion residence was built adjacent to the existing house on this property in Austin, Texas. Designed and constructed by Moontower, the structure features exposed plywood, blackened steel, clear sealed cedar, and pine, exposed structural elements, and utilitarian lighting fixtures. A balcony gives the building a treehouse feel and offers views of the Austin skyline and a nearby college bell tower.

Among our builder plans, we have developed a wide range of shed designs, which we offer in form of DIY plans. If you purchase them, you will receive a detailed shed blueprints and building instructions, from the foundations to the roof, with precise measurements in both metric and imperial systems and full list of materials required for the shed. Our garden sheds, storage sheds and gazebo plans are created in a way to make the construction process comprehensive and easy to build for anyone. Especially easy are the lean-to shed plans, narrow but spacious, very practical and possible to attach to any building or wall. 
×