If you plan to paint your shed, natural wood siding isn’t necessary. You can buy sheets of OSB (oriented strand board) siding at a fraction of the cost of real plywood, and it’ll probably last longer too. LP SmartSide panel is one brand. You can buy plain, grooved or stucco-like panels in several thicknesses and sizes. Ask at your local lumberyard to see what’s available.
Proceeding with your shed requires smart planning. For starters, you may need a permit from your local zoning authority and/or homeowners’ association to build a new structure on your property; check with the proper authorities before you even invest in the materials. Plus, there may be rules that dictate how you may use your shed, or whether you’re allowed to wire it for electricity. Once you get the go-ahead to build, you’ll want reliable guidelines. For anyone inclined to DIY rather than buy a prebuilt shed, look over a selection of free LP Outdoor Building Solutions plans based on your choice of size and roof style. Each set of plans comes with extensive material and hardware lists, detailed construction information, and tried-and-true building tips.
I felt that this is a very poorly setup web site. I purchased the Ryan’s shed plans online, did not receive an emailed receipt or link to the web site that worked. Phoned Clikbank and they promised to send another receipt. They did not. I had saved the original online confirmation with the links to the site. When I clicked on these it said the files couldn’t be found.
We’ve simplified the door-hanging process by mounting the door to a 1-1/2-in.-thick trim piece and then screwing the trim to the wall. An easy way to mark and cut matching hinge recesses in both the door and the trim is to clamp the trim alongside the door, making sure it extends 1/8 in. beyond the top of the door. Then mark the hinge cutout on both the door and the trim at the same time.
We now need to create a base that we can nail the frames for the walls into. We did this with four 2x8's and some bent i-bolts along with a lot of mortar. The basic process was that we bent the bottoms of the i-bolts after heating them with a blow torch, and then anchored these in some of the holes in the cinderblocks with a lot of mortar. Then we drilled holes in the 2x8's where the i-bolts were and put these on top and screwed them in. The frames can now be solidly attached to the base with the framing hammer.
Now we can actually start building! Before you start putting down cinderblocks, lay limestone screening down in all of the channels and run and burry your electrical. Make sure that your electrical wires are clearly marked (we used caution tape) so that nobody digs them up accidentally in the future. Once your all set, you can start putting down some cinderblocks. You may need to break some cinderblocks in half, and this is easily done with a chisel, a hammer, and a bit of time. Tip: Set Rebar posts in each corner and tie strings across to help you keep the walls straight. You need to check every single block for level, especially on this layer as the base of the foundation will affect the rest of the foundation and in turn affect the main structure.
Building a shed has lots of advantages which can vary for each person. For example, you could use the shed as a storage space for bicycles in winter. Another option is to use the shed as a storage space for large equipment like the lawnmower or the garden tools. You could also use the shed as a workspace whenever you’re doing DIY projects which is quite funny because the shed itself can be one such project. If you’re the recycling type, you can put a hatch on the side specifically for this purpose and place the bins inside. In any case, a sturdy shed can serve you for many years to come and the shed plans offered on todaysplans show you how to ensure that.
Door placement is also important. You often see doors placed on the gable end of the building, which looks nice, but makes it virtually impossible to reach items stored at the rear of the shed. A better alternative is to put the door on the long side wall, so that you'll be able to access items to the right, left and back. Another option is to install doors on both gable-end walls, so that you'll be able to easily reach items from either end of the shed.
Build the framework for all four walls. To account for the fact that the front and back walls are different from each other (due to the doorframe in the front) and the side walls must both be sloped (to prevent rain from collecting on the roof), each of these will have to be tackled somewhat differently. It’s easiest to construct the back first, the front second, and the two sides last, as shown in the numbered image below. See How to Frame a Wall for more information before you read the instructions below.
The walls of the foundation have been created and the electrical is all set, now all that needs to be done is to fill the gaping hole in between them with limestone agrigate. We also threw in some concrete paving stones that we had lying around because we don't plan on using them and we had already tried to give them away. After the limestone is in place tamp it down by jumping on it and keep filling up any places that are no longer level. After the entire base is filled with as much limestone as you can fit put a sprinkler on to soak it and set it for the next hour or so. You may need to add a bit more limestone after this is done as well.