DIY Storage Shed Kits are the same price as a regular shed. We simply partially assemble the shed kit and send it as a package for you to assemble. If you wish to have Sheds Unlimited assemble the shed kit for you there is an extra cost from 25% to 40% depending on the type of storage shed or prefab car garage you wish to purchase. The prefab cost is also added to any options on the building. In addition, there may be extra storage shed kit shipping charges depending on your location.
Now you have finished your shed!  Once your doors are on, you can add latches and locks.  The windows on our shed are made of 1/4 inch thick plexiglass held in with white silicone to match the trim.  The floor was finished with concrete tiles. You can now choose to leave the inside of your shed barren, to say, store a few larger items, or you can add shelves like we did.  We added the shelves because we had a lot of small boxes and things that we wanted to move out of the garage.  They are made from 7/16 inch thick oriented strand board and 2x2s.  The shelves in the middle have some spare 6x6 chunks keeping them up, which is suitable because they are the deepest and are designed to hold the heaviest items.  They are so strong that you can climb on them, even jump on them!  We also added a bike rack on the right hand side that can hold our five bikes.  The finishing touch on the shed was to add an electrical outlet and a flourescent lighting fixture with a switch.  There is a vent in the back wall for warm summer days but it is probably unneccesary.  Hopefully you can build your own storage shed and de-cluterize your life as well.  Thanks!
Make a template on the shed floor for assembling the trusses. Begin by laying out the parts for one truss. Align the bottom chord with the edge of the plywood floor. Then cut four 24-in.-long 2 x 4s. Lay two alongside each rafter and screw them to the plywood floor. Now use these short boards as stopblocks for laying out and assembling each truss. Fasten plywood gussets to each side of every truss with carpenter's glue and 1-in. roofing nails and set the trusses aside.

After the concrete is all ready, the sole plates are then joined together with the anchor plates which protrude out of the foundation. Use the carpenter’s pencil and measuring tape to mark about one and a half inches from the board end continually every sixteen inches till the further end. These marks guide where the studs will be placed. Mark where the anchor and the mudsill meet up with a different marker from the one used initially. The studs are then taken and galvanized nails are driven through the marked areas into the center of the board until they reach the stud bottom. The studs should be secured to the baseboard.
The shed we built rests on a foundation made up of 12 solid-concrete blocks. The 4 x 8 x 16-in. blocks are arranged in three rows spaced 59 in. apart. These blocks are typically set directly on the ground, but we put down a 4-in. bed of gravel first because our site occasionally receives groundwater. The gravel will keep the soil beneath the shed from eroding or becoming soggy.
Working from ladders is more dangerous than working from scaffolding. Plus, having to constantly move ladders around is time consuming. When you get to the roof construction, consider renting a set of scaffolding with wheels. You’ll be amazed at how much easier it is to have a stable platform to work from and to set your tools and materials on. You can rent a 5-ft.-tall section of scaffold with three planks and wheels for about $110 per week.
Since the shade is an outdoor structure, it will face various weather elements like sunshine, rain, snow, wind and other factors as insects and moulds. If you are not sure on the wood selection, it would be better to seek advice from a wood expert who will guide you through the best wood you would use to build your shed depending on the climate your region experiences.
Because the shed is designed to abut to another structure, the foundation need only be pressure-treated skids, the roof pitched in only one direction to shed water, and the back wall sheathed with 1/2-inch CDX plywood, which withstands indirect exposure to moisture. See Anatomy of an Outdoor Shed or Playhouse for more about typical shed construction.
For the masonry of the foundation we went out and bought 15 cinderblocks, and suplemented these with clay bricks that we got for free off of kijiji and some concrete pavestones from a neighbor's old patio.  Clay bricks can only be used above ground, other wise they will erode.  Looking back, it would have been easier to simply use cinderblocks and we strongly recommend it if you don't have other materials to get rid of.  Also, buy more mortar than you think you will need.  We ended up using a lot of mortar and if you have any extra you can always return it or pour it in the cinderblocks like we did to make the foundation even stronger.
I would advise you to aim for the type of wood that is resistant to deforming, fading, pets and dampness. Once at a local lumberyard, request for the heartwood, which is the innermost part of the wood in a tree. Unlike sapwood which is the outer most wood found in a tree, it is resistant to harsh conditions. The following species of wood are suitable for shed building: Cedar, Cyprus, and Redwood. Before buying the wood, check thoroughly that it has been well processed. Be cautious of wet wood to avoid shrinkage after you have already bought it and also Greenwood which may cause you inconveniences. The most common type of outdoor wood is pressure treated and consists of pine and fir.
They are more expensive compared to the small domestic sheds and have large working spaces. They are fitted with modern housing equipment like windows and electrical outlets. They accommodate more activities such as repairing equipment and relaxation. They are used by some people as outdoor offices. They can be customized by adding ventilation systems, benches, and electric lighting.
For strength, plan to build the front and back layers so the corners overlap each other. Then, to accommodate inset panels, make the front pieces a little wider to create a lip for the panels to rest against. Use plywood or tongue-and-groove boards for the panels, and hold them in with stops nailed on the back. You can assemble the two frames with pocket screws before gluing and screwing them together, but it’s not necessary. After the glue dries, plane or sand the edges to hide the fact that there are two layers.
Before we can finish the base we need to get the electrical ready.  Put a peice of conduit over your electrical wire to protect it from any damage it could receive while you are finishing the base and to give the shed a more finished look.  Make sure the pipe and wire inside are pointing up perpendicular to the ground and are preferably going straight to the location where your first outlet will be.

This 8×15 shed from Lifetime is entirely constructed in the USA, and comes equipped with two shatter proof windows, shutters, and side entry with 6 skylights for stunning illumination within. The powder coated steal A frame roof trusses and reinforced steel internal wall structure are made of durable polyethylene. The high grade metal screws make it incredibly easy to assemble this shed. Additional airflow is provided by the peak screen vent cap. You also get the added benefit of UV-protection that helps to prevent fading and cracking over time. This storage unit can be used year-round and comes with a fantastic 10 year limited warranty from the manufacturer. The floor of this unit is built so tough that it will never crack, peel, or chip. It’s also slip-resistant and resistant against stains, oils, and solvents. All in all, this is a fantastic shed for those looking for something that is built tough and built to last.
• Improper geographical placement — this is one of the huge mistakes one may make while shed building. It may be too close to your house hence obstructing your beautiful view from your living room or your kitchen as you are cooking. The last thing one would want is not like your house because of a simple thing as a view, so be careful with where you place your shed. One may also build the shed too far away from their house which again is an inconvenience. Who would want to walk from your house to your shed to get some tool you need and you have to trek some long distance? You may also need your shed someplace you can see due to the security reasons. You would want some stupid thief taking your stuff without you see them, would you? Or walking down a snowy lane during a chilly night just so you could get something from your shed. Before building your shed consider all the factors whether positive or negative and then come up with the place in your compound with the most advantages compared to disadvantages.
There are plenty of jobs to do out in the yard, and most of these tasks require tools and machines like weedwhackers, lawn mowers, edgers, and everything else. The garage can only hold so much, because it’s meant to store your car or cars. Heaven knows you aren’t going to be storing that equipment inside the house once you’re through with it, so an outdoor shed is necessary in every home’s backyard. It can cost a fortune to hire a woodworker or carpenter to customize an outdoor storage space for you. And if you take it upon yourself to build a shed, you’ll probably be left with nothing but frustration and problems.
The female version of man caves is she sheds: havens to escape that can be designed and decorated in whatever style the owner desires. Inspired by a tiny hummingbird viewed nearby, this shed is aptly named Hummingbird Cottage. Lovely photos on Instagram reveal that the shed is used for art projects, as a retreat, displaying vintage pottery, and for entertaining friends. Extras like a hanging faux-crystal chandelier, potted flowering plants, wreaths, and stained glass give it a personal touch.
Because the shed is designed to abut to another structure, the foundation need only be pressure-treated skids, the roof pitched in only one direction to shed water, and the back wall sheathed with 1/2-inch CDX plywood, which withstands indirect exposure to moisture. See Anatomy of an Outdoor Shed or Playhouse for more about typical shed construction.
The men showed up early Tuesday and went right to work.They were polite, friendly and answered any questions I asked. Although my building was on the larger side, 28' by 44' ft. they worked well together and finished in two days! Myself and two contractor friends inspected the building and were all quite pleased with the quality of the building. The men cleaned up the perimeter before leaving and other than a new building you would never know they were there. I am very pleased and would definatly recommend Sheds Unlimited.. 

The slanted roof of a modern house in the San Francisco Bay Area is echoed in this small wooden tool shed. Conceived by Astrid Gaiser Garden Design, the shed becomes an interesting part of the landscape design instead of something tucked or hidden in a corner or side yard. Gaiser even added a chalkboard for kids and adults to draw and write messages.


You can cut steel roofing panels with a circular saw and a carbide blade, but it’ll save you a lot of work if you order the panels the right length to start with. Plus, you’ll have a greater color selection if you order the roofing rather than buy off-the-shelf panels. Remember to order in advance, though, since it usually takes several weeks for the roofing to arrive. And make sure the overhangs are the right size so the panels will overhang the fascia slightly.

From start to finish, it may seem a little intimidating, but just take it one step at a time. The nice thing about building a shed is that it starts off easy (layout the foundation, building the floor, etc.), and by the time you get to some of the more daunting tasks (like the roof), you would have gained a lot of confidence/experience working your way to that point.
Cut the treated 6x6s to 12 ft. and set them on the gravel so they’re parallel and the outside edges are 6 ft. apart. On sloped ground, you’ll have to raise the 6×6 on the low side until it’s level with the adjacent 6×6. Do this by stacking treated 2x6s, 4x6s or 6x6s on top of the treated 6×6 to reach the right height. Use a 4-ft. or longer level to make sure the 6x6s are level and level with each other. Finally, square the 6x6s by adjusting the position of one 6×6. Slide the 6×6 back and forth, not sideways, until the diagonal measurements from opposite corners are equal. Build the platform with treated 2x6s, 24 in. on center, and cover it with treated 3/4-in. plywood (Figure B).

Because My Shed Plans does not promise anything beyond belief, the product’s foundation is pretty strong. People have enjoyed choosing between the collections of shed layouts and building it themselves. It’s a great activity for the whole family, since it’s all well planned out. It can be a bonding experience, the way a team building exercise at work is.
×