I would advise you to aim for the type of wood that is resistant to deforming, fading, pets and dampness. Once at a local lumberyard, request for the heartwood, which is the innermost part of the wood in a tree. Unlike sapwood which is the outer most wood found in a tree, it is resistant to harsh conditions. The following species of wood are suitable for shed building: Cedar, Cyprus, and Redwood. Before buying the wood, check thoroughly that it has been well processed. Be cautious of wet wood to avoid shrinkage after you have already bought it and also Greenwood which may cause you inconveniences. The most common type of outdoor wood is pressure treated and consists of pine and fir.
Woodworking is a creative pursuit. That’s why it should be fun and enjoyable. If you feel intimidated about taking up woodworking projects, even when you love working with wood, the problem lay not in you but in the woodworking plans you are following. Among all the woodworking projects, people find making outdoor sheds complex and hard to execute. But, that should not be the case. In fact, if the blueprint and the shed plan is good, is explained in detail with step by step instructions, making outdoor sheds should be a breeze.
Start by setting deck blocks on the ground, positioned as shown in the plans. While the area doesn’t have to be perfectly level, you should make the ground roughly level where each block will rest. Temporarily place some straight 2-by-6 lumber on edge in the top grooves of the blocks to orient the blocks in a straight line. Arrange two rows of four blocks parallel to each other to form both long walls, then measure diagonally across the outside corners to determine how square the arrangement is. If the two long walls are parallel, and diagonal measurements taken across corners are equal, then each corner is guaranteed to be 90 degrees. Finish up by placing one deck block in the middle of each 6-foot wall after you have aligned and squared the 8-foot walls.

I'm always surprised at how little forethought most backyard builders give to the shed's doors. After all, there's no sense in building a shed to store a particular item, such as a lawn tractor or wheelbarrow, if you can't fit it through the door. I saw a shed recently that had its doors removed. When I asked why, the homeowner explained that he framed the doorway wide enough for his riding lawnmower, but didn't take into account the amount of space taken up by the hinged inset doors. So, he had to remove the doors to fit the mower inside. (He's in the market for a skinnier mower.)
My Shed Plans is the perfect package for those who do not have an ounce of knowledge regarding shed building. You will benefit from the step-by-step directions, colored illustrations, section details and the woodworking course. All techniques and tricks will be taught to you, so you’ll definitely learn a lot about building your own sheds. If you do have some natural creative ability and some skill, the sheds should turn out fine.
A garden shed can be strictly functional, but it can also be a decorative focal point around which you design your garden or yard. These plans will help you build a basic shed, but don’t stop there! To customize your shed, you could create a combination toolshed and greenhouse, put a martin house on top, or use part of the shed for a chicken coop or rabbit hutch. If you’re feeling even more adventurous, you could create a living roof of moss or succulent plants.
For a freestanding shed, you can build the shed on top of a concrete slab (see Pouring a Concrete Slab) instead of the pressure-treated skids and floor joists; this will actually result in a sturdier—more permanent— structure. Otherwise, for a freestanding shed, the foundation should be constructed on concrete piers or poured footings (see Pouring Concrete Footings & Piers).  Be aware that building on footings will raise the height of the shed up from the ground.

There are many ways and methods of beginning a foundation for your shed, but so as to keep this manual simple we will begin by looking at the procedures followed while building a shed. The types of the foundation include a concrete slab foundation, a sunken pillar, and wood skid. The e-book is helpful to those who might not be interested in shed building from the scratch. It takes time to explain in detail the materials required and the step by step methods required to give one the moral to build the shed. It also explains the easy steps in a very fun way. Furthermore, the process of building your shed on your own is quite a fun task as one watches the shed start from nothing to something beautiful and useful. Isn’t that exciting? At least one feels useful after performing such type of a task that feels to be quite a huge burden. The following steps are derived from the e-book on steps used to build a foundation:
For example, the last three sheds I built were trimmed with white PVC trim boards instead of painted cedar 1 x 4s. This new plastic lumber, which I used for the rake, fascia, frieze and corner boards, is impervious to bugs, warping, splitting or decay, and it never needs painting. Other low-maintenance options include: vinyl or aluminum windows, faux-slate roof shingles, fiberglass or steel doors, composite decking for steps, and fiber-cement siding. (I don't usually recommend aluminum or vinyl siding for sheds; neither material is rugged enough to survive the inevitable beating outbuildings take.)
Because the shed is designed to abut to another structure, the foundation need only be pressure-treated skids, the roof pitched in only one direction to shed water, and the back wall sheathed with 1/2-inch CDX plywood, which withstands indirect exposure to moisture. See Anatomy of an Outdoor Shed or Playhouse for more about typical shed construction.
My Shed Plans by Ryan Henderson is not just your run-of-the-mill collection of a few hundred shed plans, but it is a collection of whopping 12,000 shed plans. Yes! You heard it right. And each one of them is accompanied with detailed, step by step instructions and diagrams, tool and material list ensuring that nothing goes wrong when you start with one.
All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!
For strength, plan to build the front and back layers so the corners overlap each other. Then, to accommodate inset panels, make the front pieces a little wider to create a lip for the panels to rest against. Use plywood or tongue-and-groove boards for the panels, and hold them in with stops nailed on the back. You can assemble the two frames with pocket screws before gluing and screwing them together, but it’s not necessary. After the glue dries, plane or sand the edges to hide the fact that there are two layers.
Build your own shed and you'll instantly have increased space for your tools, a place to work on DIY projects and a way to keep your garage free of clutter. There are many shed plans online that show you how to build your own shed from scratch using wood. It may be easier, however, to use a kit to create a resin, metal or plastic shed instead. A storage shed kit contains all the materials you need including trim. This Home Depot project uses the Keter Stronghold Resin Shed Kit to show you how to build a shed from a kit. We also offer a large variety of other types of shed designs to choose from. Like most, this DIY shed requires tools like a power drill and step ladder to put it together, but assembly instructions will vary by kit. Make sure to follow the manufacturer's instructions carefully.
Well, not these plans. You have the option of building a very functional and spacious lean-to shed on different foundations. Your foundation choices are a concrete slab, a wooden floor supported by concrete piers, or a wooden floor supported by skids. That lost option also means that your lean-to could be mobile as well so you won’t have to decide where you want to permanently put it.
The construction of a wood foundation is usually built using pressure-treated 2x6 lumbers. These parts are called the band on the ends and the joist in the middle of the band, spaced out 16-24 inches apart. The foundation frame will sit on top of pressure-treated 4x4 posts called skids. The skids will set on the cinder blocks or on top of gravel to prevent rot.
For those who don’t quite believe in My Shed Plans, they offer a 60 day trial. If within those 60 days, you feel like the product hasn’t lived up to its hype, you may return it and receive a full refund. A decent outdoor shed can be built in a week or two depending on your schedule, and the amount of time you have to build it. Therefore, 60 days is enough for you to test out the product and see what you come up with. If you have a shed worthy of showing off to your buddies, or gal pals, then keep it. If you have a heap of materials in a pile that resembles something Homer Simpson might have created, then return it. No big deal.

Because most DIY manuals and plans are written by ghostwriters who don’t know anything about carpentry, it is common to find incomplete guides. This package is different. Ryan has spent time and effort ensuring that his expertise is laid out in a way that anyone can follow. After all, he is an educator. You also save because the plans make sure you don’t waste material.


You can cut steel roofing panels with a circular saw and a carbide blade, but it’ll save you a lot of work if you order the panels the right length to start with. Plus, you’ll have a greater color selection if you order the roofing rather than buy off-the-shelf panels. Remember to order in advance, though, since it usually takes several weeks for the roofing to arrive. And make sure the overhangs are the right size so the panels will overhang the fascia slightly.
When people talk about the different types of shed available, what they should describe are the different types of roof available, since sheds only really differ by the type of roof they have. We provide shed plans for three types of roof: Gable, Lean-To and Hip. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-To sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-to sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage. Gable, Lean-To and Hip roofs each have their pros and cons. Gable roofs are the most common since they are simple to build and offer plenty of space. Lean-To sheds are popular too for confined spaces. Hip roof sheds are the most complex to build, but they are arguably the most desirable too since they have a more uniform appearance. In terms of shed size, you should choose one that fills the space you have in your yard but you should also consider the overhang for the roof. A 16X24 shed is big enough for vehicle storage and to be used as a workshop, while a 12X16 shed is perfect for storing all your yard tools and mechanical equipment. Sheds smaller than this are fine for basic storage.
We make great shed plans.  It’s all we do and we love it! All of our shed plans are available to download instantly at checkout. There isn’t an easier shed plan checkout process on the web!  When you buy a plan from us, you are guaranteed a great plan at a great value.Every one of our 200+ plans are easy to build thanks to our thorough and easy to follow instructions. All of our shed plans come with more information compared to the competition. Things like a tool list, a cut list, and a material list in excel format are all included.
My Shed Plans is the perfect package for those who do not have an ounce of knowledge regarding shed building. You will benefit from the step-by-step directions, colored illustrations, section details and the woodworking course. All techniques and tricks will be taught to you, so you’ll definitely learn a lot about building your own sheds. If you do have some natural creative ability and some skill, the sheds should turn out fine.
Build the framework for all four walls. To account for the fact that the front and back walls are different from each other (due to the doorframe in the front) and the side walls must both be sloped (to prevent rain from collecting on the roof), each of these will have to be tackled somewhat differently. It’s easiest to construct the back first, the front second, and the two sides last, as shown in the numbered image below. See How to Frame a Wall for more information before you read the instructions below.[5]
Normally we try to help our customers as much as possible, especially if it is a matter of helping to figure out where certain material goes on the building. Keep in mind, you are responsible for correctly constructing the shed if you purchase a kit, but we can offer direction. (Prior construction experience is recommended.) If there is any uncertainty about whether or not you will be able to assemble the storage shed, consider one of our build-on-site options and we will send a team to assemble the building for you.
Build the framework for the back wall. Make the top and bottom beams (a.k.a. the plates) the same length as the length of the floor which they sit. To keep your measurements simple, make the spacing between the vertical studs identical to the spacing between your floor joists. Note that the back wall should be lower than the front wall so that the roof slopes and directs rain away from the door.[6]

Start by setting deck blocks on the ground, positioned as shown in the plans. While the area doesn’t have to be perfectly level, you should make the ground roughly level where each block will rest. Temporarily place some straight 2-by-6 lumber on edge in the top grooves of the blocks to orient the blocks in a straight line. Arrange two rows of four blocks parallel to each other to form both long walls, then measure diagonally across the outside corners to determine how square the arrangement is. If the two long walls are parallel, and diagonal measurements taken across corners are equal, then each corner is guaranteed to be 90 degrees. Finish up by placing one deck block in the middle of each 6-foot wall after you have aligned and squared the 8-foot walls.


The roof trusses support the plywood and shingles that make the roof waterproof.  They are very important to plan carefully because they require strange angles and they have to fit the structure below them.  We gave our shed a slight awning and this had to be accompanied by the trusses, which overhang the walls of the shed by about a foot on each side.  When constructing your joists it is important to use joist plates otherwise the angles that you so carefully planned will not remain true for very long.  We used a 2x4 to support the joists while we were attaching them to the walls.


A shed is a simple roofed single floor structure that is used for storage of garden tools, shelter domestic animals, performing out hobbies and also as a workshop. They can also be referred to as outhouse, outbuilding or shack. They are mostly situated in the back garden. Sheds vary in their sizes from large sheds to small sheds depending on their purposes. Storage sheds are mostly small in size but industrial and farm sheds are mostly large depending on the volume of the goods they hold. Sheds can be built from different materials like wood, metals, and plastic. The types of shed construction include metal sheathing, plastic sheathing, and complete wood construction.
But I've never drilled a pilot hole in my life, so what do I know. No seriously, unless it's super delicate or thin, I just use the impact driver and make it work. Sure, sometimes the wood splits a bit, but I don't care about looks and most of my projects are built with pallets and discarded stuff anyway. But the thought of predrilling every hole?? And messing a corded driver?? Come on dude, that's laughable!
• Time underestimation — people normally underestimate the time taken to build any given structure. It is a normal occurrence when building delays, the delays may be caused by issues as inadequate tools and climatic changes that would not allow outdoor activities as the building. Building any kind of structure may take longer than expected. It is therefore important to do things at a fast rate to reduce the number of delays that one has to encounter and also reduce frustration brought about by delays. Completion of construction is also advantageous as one gets to start using the structure sooner than expected which to some extents save on your finances.
Well, if you look at the name of the project, it doesn’t actually appear to be what it says. The title says that Ryan Shed Plans also known as MyShedPlans contains a compendium of 12,000 Blueprints. But if you look at the package carefully, the phrasing on the website contains 12,000 Woodworking Shed Plans and Shed Designs. Most of the blueprints are ShedPlans that cover both small scale and big scale projects, and you can come across thousands and thousands of different blueprints with different architectural, functional and aesthetic features.​
If you're always in a hurry and terrible with commitments, I might suggest you rent a storage space or continue parking your forty thousand dollar cars in the driveway and save your garage space for unused furniture, bicycles, unpacked boxes, garden rakes, and lawn mowers. Because, the biggest enemy in do-it-yourself is not the lack of carpentry skills or ability to follow directions, but lack of planning and failure to schedule the time it takes to get the job done.
Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.
Because most DIY manuals and plans are written by ghostwriters who don’t know anything about carpentry, it is common to find incomplete guides. This package is different. Ryan has spent time and effort ensuring that his expertise is laid out in a way that anyone can follow. After all, he is an educator. You also save because the plans make sure you don’t waste material.
These plans are for saltbox roof style sheds.  They are built with trusses that you build.  These sheds are perfect for general storage, garden sheds, tool sheds, potting sheds, playhouses and more.  This shed in my opinion, if you are wanting to build a shed for gardening, this is the one.  It has lots of charm and character with it's desirable design.
Our free shed plans offer a solid introduction to shed construction and building technique, and they include a full materials list to help get you started. The instructions provided are basic, but if you have existing experience with construction, then they may well suffice to help you build your shed without having to spend money. Our premium shed plans are on another level, however. They include detailed, step-by-step instructions and they walk you through the entire shed building process. We also include professional-grade tips on select pages to help you as best we can – it’s like having an expert right next to you every step of the way. All the techniques you will learn from reading our premium shed plans are transferrable too, and they can help even the most seasoned builders perfect their skills. Therefore, we recommend premium shed plans to anybody who is serious about building their own shed, with our free shed plans best-suited as a taster for those interested. Hopefully, you’ve now understood that here at 3DSHEDPLANS™ we do not promote or employ any marketing gimmicks. Download our FREE shed plans and see it for yourself. Don't forget to SUBSCRIBE to our newsletter to get special deals, offers and discounts!
If you need lots of space for storage, garden room, or office space, the most common design will be the gable shed. The gable roof design has two sloped roof that resembles a little house. This design is the most popular because it blends will with your home. The gambrel shed resembles a barn. It is great for storage as no space will go to waste. A larger size gambrel shed will have enough room to build a loft. Having a loft will keep everything organized and allow you to store more stuff. By installing a ramp to the shed you can also store ATV, snowmobiles, jet skis, trailers, and such things.
There are a number of considerations when it comes to choosing an outdoor storage shed for your home. There’s the question of price, design, climate, size, and more. To begin with, realize that you get what you pay for with a storage shed. Saving a few hundred bucks on the cheapest model might not make the most sense in the long-term. This means that you’re passing on quality siding materials like cedar and vinyl. Next, think about how you want the shed to look in your yard. We’ve all seen those classic storage sheds that are designed to have the same aesthetics of your home. For instance, rustic designs for a country-style home. These complementing designs can be quite charming, and allows the shed to stand out as an addition of your home. Another option is to have your shed bleed into the landscape by covering it with plants or by planting perennial beds around the unit.

This step by step diy project is about diy 12×16 shed plans. If you are looking for a large storage shed that is both easy to build and that has a really nice appearance, then you should take a look over my plans. This garden project has more parts so take a look over the rest of the sections to learn how to build the roof and the door. Moreover, I have designed shed with many sizes so check them out, as well. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.
Can you believe that building this cedar shed costs less than $300?! Yes, you read that right – a retail price for something similar can be around $1600, so this is one heck of a good deal. Not only is it incredibly good looking and budget friendly, it’s big enough to store all your outdoor items yet it won’t get in your way thanks to the compact design.
We found all the materials to build this shed at our local home center. Most of the construction is straightforward and requires only standard carpentry tools and a circular saw. For how to build the shed windows and door, you’ll also need a table saw, power miter saw and router. We used a Kreg pocket hole jig and pocket hole screws to assemble the door and windows. Another really great thing about small storage sheds such as this on, it don’t take as long to build! With a helper or two, you could have the platform and shell built in two or three days. Then expect to spend four or five more days completing the siding, trim, doors, windows and roofing.
In reality, the Ryan Shed Plans also known as MyShedPlans Elite; is a huge collection of different wood construction plans, craft designs, shed blueprints, storage shed designs, birdhouse designs, garage designs, rocking horse sheds and even the end table designs. All the plans that are contained in Ryan Shed Plans contain step by step instructions like you have expected, and therefore, these are more than just mere designs. They naturally include a variety of blueprints of the same shed design the plan, the elevations, the sections, perspective of the shed, a description, legend containing the materials, tips and tricks but a few of them admittedly are not as designed as the rest.​
· Wood sheds — these types of sheds are made of wood. They are the most common type of shed compared to metal and plastics. They are the most conducive as they can be used as children playhouses, outdoor office and still storage of garden tools. They are also easy to modify and renovate as increasing their size. They are preferred to other types as they blend well with the environment and give the environment a good natural look. However, they must be maintained regularly from insects as termites which feed on wood.
Complete the siding, then remove the toe-screws and move the wall aside to make room for constructing the opposite wall. Use the same chalk line template and process to build the opposite end wall. Figure C shows framing details for the front wall. Mark the curves on the 2×10 header pieces using the trammel setup shown in Photo 12 and Figure G. Cut them with a jigsaw. When you’re done building the front and back walls, set them aside so you can use the platform to build the roof sections.
I don't waste my time on free plans, store-bought sheds, or ready-made, mail order kit solutions... been there, done that. Free means lack of user feedback and you get absolutely no customer support. With store-bought and ready-made mail order sheds: they're flimsy, profit-driven solutions that I've always had to tear apart and modify too much to get the storage space to work or to match the character and style of the home.

Also square the frame by making sure diagonal measurements from opposite corners are equal. Then tack one corner to hold it square. Finally, nail the soffit to the roof frame with 6d galvanized box nails. We used 12-in.-wide fiber cement siding for soffit material. Mount an inexpensive carbide blade on your circular saw to cut the fiber cement. Set the roof panel aside and build the other half of the roof using the same techniques.
Assemble the four wall structures. Wall structures are usually nailed to the underlying support from the bottom up. However, if this is not possible with the design you’ve chosen, simply nail them downwards through the plywood and joists or toenail them into place by driving the nails downwards and at an angle. Note that you will probably need other people to help you hold the wall structures up until they can be attached to one another.[9]
Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.
Figure G shows details for the marking jig. Photo 12 shows how to use this setup to draw the curves for the window pieces. Next cut the side pieces (Figure F). Set the side pieces in place over the top of the header and mark the angled cuts (Photo 13). Finish the curved trim piece by first cutting the angles on each end, and then sawing the curves with a jigsaw and sanding them smooth. Use the marking jig to lay out the curved brace, too (Figure G).
When you buy this package of shed designs, you have access to the plans for a lifetime. You also get a few bonuses, including a book of professional woodworking tips and extra designs for a variety of woodworking projects. Spend less than $40 today, and you may have what you need to build furniture, toys, sheds and other items for the rest of your life.
Shed are also great if you have a hobby. For example, if you’re passionate about pottery, gardening or even painting, you could use the garden shed as your private workspace. You can give it windows if you think you’ll need natural light inside. In fact, this can be an opportunity to upcycle some old windows and doors. Check out this project that we found on countryliving to see how this chic shed was built.
We have a large selection of small horse barn plans, tack rooms and run in shed plans. Each of our designs comes with a materials list and construction plans to help you save time and money when you build. We have many different sizes of horse barns including one, two, three and four stalls. Most of the barns and run in sheds are designed to be built with pine board and batten siding on the outside and a 4' tall Oak kick board on the interior.
Among our builder plans, we have developed a wide range of shed designs, which we offer in form of DIY plans. If you purchase them, you will receive a detailed shed blueprints and building instructions, from the foundations to the roof, with precise measurements in both metric and imperial systems and full list of materials required for the shed. Our garden sheds, storage sheds and gazebo plans are created in a way to make the construction process comprehensive and easy to build for anyone. Especially easy are the lean-to shed plans, narrow but spacious, very practical and possible to attach to any building or wall.
×