These days, it is not very easy to translate your wooden shed plans into a standard written format without losing any valuable information. In order to learn how to build high quality wooden sheds, it is important to consult an expert. However, consulting an expert may not be viable for every individual. In addition to this, the internet provides you with extensive information about a wide range of subjects. 

When you nail on the siding, make sure it overhangs the framing on each side by 3-1/2 in. and that you’ve trimmed off the top corner to follow the slope of the angled top plate (Photo 2). Attach the siding with 2-in. galvanized or stainless steel ring-shank siding nails placed 8 in. apart along studs and 6 in. apart along the edges of the sheets. You’ll have to nail blocking between the studs to support the top edge of the siding and the Z-flashing.
You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls. Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center (Photo 1). You’ll use this line to make sure the angled top plates meet in the center.
These plans are for saltbox roof style sheds.  They are built with trusses that you build.  These sheds are perfect for general storage, garden sheds, tool sheds, potting sheds, playhouses and more.  This shed in my opinion, if you are wanting to build a shed for gardening, this is the one.  It has lots of charm and character with it's desirable design.
This 8×15 shed from Lifetime is entirely constructed in the USA, and comes equipped with two shatter proof windows, shutters, and side entry with 6 skylights for stunning illumination within. The powder coated steal A frame roof trusses and reinforced steel internal wall structure are made of durable polyethylene. The high grade metal screws make it incredibly easy to assemble this shed. Additional airflow is provided by the peak screen vent cap. You also get the added benefit of UV-protection that helps to prevent fading and cracking over time. This storage unit can be used year-round and comes with a fantastic 10 year limited warranty from the manufacturer. The floor of this unit is built so tough that it will never crack, peel, or chip. It’s also slip-resistant and resistant against stains, oils, and solvents. All in all, this is a fantastic shed for those looking for something that is built tough and built to last.
• The ceiling is too low — these may tend to be one of the least concentrated on problems as they happen least when one expects. It is important to be aware of the low ceiling so as to save on your funds in putting a higher one. Ensure that each and every measurement is taken carefully and is also executed. The best way to determine the height of your shed is by scanning through the items you are planning to store there and use the tallest. As mentioned earlier, the installation of steep roofs might be risky but in the long run become an added advantage as they create more space inside the shed.
I just want to let you know that your Driver was a pleasure to deal with. He placed the shed perfectly into a tight spot and then took the time to make sure it was level and sitting properly. I feel any other company would of placed it as close as possible to where i wanted it and would of been on their way. He also noticed (I would of never noticed) that the door didn't line up perfectly when closed and made some adjustments.
Well, if you look at the name of the project, it doesn’t actually appear to be what it says. The title says that Ryan Shed Plans also known as MyShedPlans contains a compendium of 12,000 Blueprints. But if you look at the package carefully, the phrasing on the website contains 12,000 Woodworking Shed Plans and Shed Designs. Most of the blueprints are ShedPlans that cover both small scale and big scale projects, and you can come across thousands and thousands of different blueprints with different architectural, functional and aesthetic features.​
Thanks for sharing such detailed plans Seamster. I'm hoping to build a very small lean-to tool shed (2.5X4.5' base) for my very small yard and this has given me a lot of insight. Currently, theor the table and mitre saws I inherited are stored in our spare bedroom... eventual nursery room. I want to get them into their own space outdoors sooner than later. Here in North Carolina with the humid summers I think it would be best to add some housewrap to the walls to help protect the tools. I also have a situation where the back wall will only be 4-6" off the house so need to construct/panel my walls before erecting them. Do you know if it's reasonable to panel then wrap each wall frame, side it and then finally erect and fasten? Would be very grateful for your thoughts!
Build rafters across the roof and separate them with blocking. These should overhang the walls of your shed for increased weather protection. Again, your measurements will be greatly simplified if you space the rafters the same way that you spaced your floor joists. When you’re done, attach pieces of blocking between each pair of rafters along the top plates.[10]
I have recently purchased a house with an older roof that needs to be restored soon. So, I am trying to decide on I should go with a metal roof other than shingles. If I install metal roofing over solid decking such as OSB or plywood, integrate with a properly insulated garret, there is very little noise difference compared to standard asphalt shingles. I have briefly read benefits and drawbacks of Metal roofing but as I listed before I should go to metal roofing and hiring a roofing contractor no matter its expensive or noisy anyhow, Your article has cleared a lot of misinterpretation I’ve had before.
Start by setting deck blocks on the ground, positioned as shown in the plans. While the area doesn’t have to be perfectly level, you should make the ground roughly level where each block will rest. Temporarily place some straight 2-by-6 lumber on edge in the top grooves of the blocks to orient the blocks in a straight line. Arrange two rows of four blocks parallel to each other to form both long walls, then measure diagonally across the outside corners to determine how square the arrangement is. If the two long walls are parallel, and diagonal measurements taken across corners are equal, then each corner is guaranteed to be 90 degrees. Finish up by placing one deck block in the middle of each 6-foot wall after you have aligned and squared the 8-foot walls.
Building a Shed should be a fun project that provides the satisfaction of creating something and a sense of accomplishment. We have put great effort into our shed plans to make them easy to follow and work from. The How To Build A Shed eBook that is included with every shed plan is designed to show all the different steps involved in building a shed. The materials list is detailed out so that every part of the shed has a label which makes it easier to put each part where it goes. Let us know how your shed building project goes, we love to hear about and see photos of our customers building their sheds! Find the email address at the top of this page to send in your shed building photos.
Because My Shed Plans does not promise anything beyond belief, the product’s foundation is pretty strong. People have enjoyed choosing between the collections of shed layouts and building it themselves. It’s a great activity for the whole family, since it’s all well planned out. It can be a bonding experience, the way a team building exercise at work is.

Building a shed is more or less like building a miniature house. It can be a pretty fun project, especially if you have someone who can help. If you’re new at this, we found the perfect tutorial for you. Be sure to check out these shed plans that we found on popularmechanics. The whole process is described in detail, with instructions, lists of supplies needed for each part of the project and useful tips.

The best spot for a shed is level, well-drained ground close to where you work in your garden or yard. The location doesn’t need to be perfectly flat; the foundation design shown in the plans allows for adjustments to make the floor level. Small sheds require only a top-of-soil foundation, even in locations with freezing winter temperatures. Precast concrete deck blocks work perfectly for this.