Finding MyShedPlans seemed too good to be true; 12k shed plans, 3-D renderings, detailed material lists, but wait, there's more! Hundreds of useful guides, woodworking books, and project ideas ranging from birdhouses to bridges. And what was more, was the promise of an easy download and immediate access to boundless amounts of material so I could be right on my way to a sharp new shed.
The framing is the most important part of the above-ground structure because it stiffens up the plywood boards and supports the roof.  You will need a lot of 2x4's, and a way to attach them.  We used this as an excuse to buy some new air hammers from canadian tire.  We were able to get the lumber for the entire project delivered by a company called Tamrack Lumber.  They brought out a truck and dropped off all the supplies.  For the roofing you will need little plates with groups of nails sticking out of them which I believe are called joist plates.  These are used on the angles to keep them from shifting.  The last thing you will need is a way to cut all of the 2x4's.  To do this we borrowed a very nice miter saw from a friend for a few days.  It is much easier if the cutting tool can cut on angles, otherwise you will be left to improvise when cutting the peices for the roof.
@diy-plan: Thank-You for your best wishes on the Isacc, believe we always lose sleep when one is on the way. Your advice on not buying factory kit sheds I am 100% in agreement with, they are poor quality lumber, never pressured treated, steldom last more than ten years, here they are lucky to make it six years. I was asked to put one together by a friend after her son bought it for her as a gift, I almost had to rebuild it and when I was finished I thought what an ugly building. Five years later it had termites. When a shed is built on a wood base the base must be anchered into the earth, I have seen sheds flipped upside down after a storm when they are not anchored. I built a shed for a workshop a few years ago to build custom canoes in it, to make it storm ready I used OSB under the siding, then cross braced the studs, insulated it, then covered the studs on the inside with 5/8 inch plywood. The windows have storm shutters that I built for them, if this building fails in a storm I hope I am near the Canadian border.
Our 14 by 24 one car garage was delivered and set up early November. The truck pulled up shortly before 7 am and left by 5 pm after the garage was completed and cleaned inside and out. Two carpenters worked tiredlessly without even a lunchbreak to make sure that everything was complete by the evening. Despite the workpressure the always had a kind word and did not mind to answer our stupid questions. We haven't seen such a work ethics for quite some time. On top of it, the garage looks terrific and matches the style of the house. When asked I will recommend Sheds Unlimited without any reservation - a job very well done!
Can I tell you a secret? I don’t think I would ever do this again because I have another secret. Shhh, don’t tell, but DIY projects that are a joint effort between my hubby and myself really aren’t fun. They are stressful, and hard and take a toll on us. Which may seem strange in a way because we are both handy and we both enjoy these type of projects and we even have a pretty good idea as to what we are doing. Actually, I think we really have it together – separately! Once you throw the two of us together is gets a little intense. Enough about that, let’s get on to the project.
A lean to shed is the perfect way to build up against a fence or wall and still have plenty of room in your yard. It also keeps water away from the structure you are building up against. The lean to shed design is the simplest design of shed to build because of its single plane sloping roof which makes the roof easy to build. We have many different configurations and sizes either with double or single doors. The larger lean to designs include optional plans to build the doors on any side of the shed. Our smaller lean to style sheds have a 4 in 12 pitch roof and our larger designs have a 2 in 12 pitch roof to keep the overall shed height lower and help reduce shed construction costs.

I don't waste my time on free plans, store-bought sheds, or ready-made, mail order kit solutions... been there, done that. Free means lack of user feedback and you get absolutely no customer support. With store-bought and ready-made mail order sheds: they're flimsy, profit-driven solutions that I've always had to tear apart and modify too much to get the storage space to work or to match the character and style of the home.
Because My Shed Plans does not promise anything beyond belief, the product’s foundation is pretty strong. People have enjoyed choosing between the collections of shed layouts and building it themselves. It’s a great activity for the whole family, since it’s all well planned out. It can be a bonding experience, the way a team building exercise at work is.
Working from ladders is more dangerous than working from scaffolding. Plus, having to constantly move ladders around is time consuming. When you get to the roof construction, consider renting a set of scaffolding with wheels. You’ll be amazed at how much easier it is to have a stable platform to work from and to set your tools and materials on. You can rent a 5-ft.-tall section of scaffold with three planks and wheels for about $110 per week.
The sheds available can be distinguished easily as they come in pale green that eventually fades into silvery grey. The Pressure treated sheds are relatively a bit costlier than the DIP treated sheds and the advantage of using them is that they don’t need further preservative treatment and can serve the whole during the entire ten years saving a lot of time and money.​
A tool shed is pretty easy to build. We found this inspiring example on thecavenderdiary which, as you can see, has a pretty straight-forward, traditional look. It has its back on the wall and inside there’s not much worth mentioning, except maybe for those practical storage hooks, shelves and rods on the inside of the doors. Check out the plans for this toolshed and find a way to customize them according to your own storage needs.
Before we can finish the base we need to get the electrical ready.  Put a peice of conduit over your electrical wire to protect it from any damage it could receive while you are finishing the base and to give the shed a more finished look.  Make sure the pipe and wire inside are pointing up perpendicular to the ground and are preferably going straight to the location where your first outlet will be.
· Personal belongings storage shed — as you are growing older each and every day, you may tend to accumulate so many items that congest your house. You may not want to throw or give away any of the items accumulated as they probably hold a sentimental value to you. The best way in which you can solve a headache is by building yourself a shed which you can be storing your personal items as you continue accumulating them.
It can be easy to get excited and overestimate your DIY abilities when you start a new project. The passion and excitement makes you want to dream big and get creative. But blindly following your imagination can be a step in the wrong direction. If you’re a newbie to DIY woodworking, then you’ll probably want to keep it simple. Otherwise you run the real risk of ending up with a sub par build or even having to rebuild it altogether.

Each truss is made up of two 2 x 4 rafters and one 2 x 4 ceiling joist. The three boards are joined together with 1/2-in. plywood gussets. To speed up the assembly process, build all the trusses on the shed floor before erecting the walls. Start by cutting all the rafters to length with a 40° angle at one end of each. Cut 2 x 4s to 10 ft. long for the bottom chords of the trusses. Also, cut all of the plywood gussets.
I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks
Most of the Amish Built Sheds Unlimited storage sheds can be custom ordered as a DIY STORAGE SHED KIT PACKAGE for assembly on-site. If for any reason installing a completed storage building into the backyard is not an option or if you are simply a handyman at heart and would like to try your own skills, then a Economy Shed Kit, Vinyl Sided Storage Shed Kit, Classic Amish Sheds Kit or a Premier Garden Storage Shed Kit might work perfectly for you.
· Gable shed — they are also common due to their stylish two-faced roof that meets at the center forming a peak. Their roof shapes are conducive as they provide adequate space, but not as much as the gambrel styled sheds. They provide adequate spaces for storage of garden tools. They also accommodate larger items as motorcycles. The property that makes these sheds become common is their stylish shape that blends in well with any compound with a house of any design.
It’s vital to build your shed on a stable, level location—and never in a wet, low-lying area or on a downward slope. And no matter how well a shed is constructed, it won’t hold up on a weak base. A proper foundation is key, one that sets the shed slightly off the ground to aid water drainage and reduce moisture transfer. There are different foundation options, depending on where you live and the size and intended use of the shed, so bone up on the fundamentals and assess your options with this advice from the LP Outdoor Building Solutions team.
• Lack of harmony — building a shed that does not match the design or the color of your house would make the compound look a bit odd. It is advisable that you choose a suitable architectural design and color that will closely match with your house. That gives your compound a great look and also makes it look like both structures were built at the same time. It also gives you a sense of satisfaction and hence you will not have to waste money in the future to make one structure resemble the other.
The program consists of a wide range of downloadable files, which contain many different step by step instructions and plans related to woodworking. These tutorials are focused on a wide range of projects, such as potting shed plans, wood shed plans, storage shed plans, garage storage plans, house plans and more. All the shed plans discussed in this program are divided on the basis of each project type.
But I've never drilled a pilot hole in my life, so what do I know. No seriously, unless it's super delicate or thin, I just use the impact driver and make it work. Sure, sometimes the wood splits a bit, but I don't care about looks and most of my projects are built with pallets and discarded stuff anyway. But the thought of predrilling every hole?? And messing a corded driver?? Come on dude, that's laughable!

The design of the shed you choose will depend on what you will be using it for and were it will be located. If you just need a small shed to place garden equipment, a lean to shed can be ideal. This design of shed will not take much room and it can be placed next to a fence or wall. The lean to shed has a single sloped roof design. It is one of the most common for garden tools as well as pool equipment and chemicals.
We provide outdoor shed plans that are affordable and easy to build from. Our storage shed plans are organized so that you can buy shed plans and build your own shed no matter what your skill level. There are helpful how to build instructions and tips that go along with each stage of the storage building process from the foundation, floor, walls to the roof. Building your own shed saves you money and is a very rewarding experience that adds value to your property. Click the shed images above to view our library of over 200 storage shed plans.
Modern Sheds are defined by their clean and simple looks. They are perfect to be used as a home office, work studio or even a cool place to store things. With lots of windows, a simple low slope metal roof and horizontal siding, these plans are a great way to build a professional work space right in your back yard. Building a home office or work studio in your backyard will eliminate the commute to work and at the same time give you a quiet professional place to work and bring clients.
Our backyard storage shed plans are defined by their cost effective quality construction and simple to build designs. Their construction includes 2x4 framed walls, T1-11 grooved plywood siding, asphalt roofing and a strong sandwich construction door. You can buy shed plans with different pitches of roof slopes The lower pitched roof and simple trim make them easy and inexpensive to build. If you are looking for storage shed plans that are designed to be easy to build from and as cost effective as possible, the backyard shed plan line is your best choice.

The sheds available can be distinguished easily as they come in pale green that eventually fades into silvery grey. The Pressure treated sheds are relatively a bit costlier than the DIP treated sheds and the advantage of using them is that they don’t need further preservative treatment and can serve the whole during the entire ten years saving a lot of time and money.​


You can even go online and look up prices!  For example, if you visit lowes.com, they have a search box where you can enter in the item and find out each price!  This will save you some time.  The only drawback I see to this is that I find it really beneficial to go to these big box lumber stores and see exactly what I want.  For example, the LP Smartside siding panels I recommend to use:  some stores carry a cheap variation of these that have a brown color to them on the inside of the panel, and this is not what you want!  The have the consistency of a 'fibre' panel that will crack easy.  The true LP siding panels are pre-primed on the outside surface and have a natural osb color on the inside surface.

It isn’t a requirement that this shed be built against a wall—but the structure is designed to take advantage of the wall for strength. So if you modify it to be a freestanding shed, you’ll need to build a conventional stud wall across the back and face it with the same type of plywood siding used on the rest of the shed. For information on how to mark, cut, and fasten wall studs, see How to Frame an Interior Wall (ignore the part about working with drywall because you’ll be using exterior-rated T1-11 siding instead).
Made from durable blow molded resin, this Alpine shed from Suncast comes complete with 14 windows with delightful contrast trim. The double doors are built with articulating metal hardware so they’re robust and durable. The floor is reinforced for the ultimate sturdy foundation. Extra roof support is provided by the metal trusses and ridge beaming. This shed is perfect when you’re looking for something that is built tough, and stands out beyond the more flimsy and cheap designs that you find on the market. It is large enough to stow everything that you need and keep all items clean, safe, and secure. The outer appearance of this shed makes it perfect for those who want an attractive external design that doesn’t stick out like a sore thumb in your yard. All in all, customer reviews across the board are quite positive for this shed, and it makes a great addition to anyone’s home.

The framing is the most important part of the above-ground structure because it stiffens up the plywood boards and supports the roof.  You will need a lot of 2x4's, and a way to attach them.  We used this as an excuse to buy some new air hammers from canadian tire.  We were able to get the lumber for the entire project delivered by a company called Tamrack Lumber.  They brought out a truck and dropped off all the supplies.  For the roofing you will need little plates with groups of nails sticking out of them which I believe are called joist plates.  These are used on the angles to keep them from shifting.  The last thing you will need is a way to cut all of the 2x4's.  To do this we borrowed a very nice miter saw from a friend for a few days.  It is much easier if the cutting tool can cut on angles, otherwise you will be left to improvise when cutting the peices for the roof.
Pressure treated sheds, on the other hand, are made out of timber planks that usually have moisture which is sucked out of them using a special cylinder under vacuum conditions. After the moisture is sucked out, a preservative is added to the wood at a relatively high pressure until the preservative is absorbed into the grain, making it an integral part of the wood. This particular type provides around 15-year guarantee as mentioned by the manufacturers even against harsh weather.
Ryan’s Shed Plans is going to turn you into the ultimate builder – a builder of sheds, a builder of greenhouses, a builder of tiny homes, and a builder of many things. And nope, no previous experience is needed. This unique online program breaks down the steps to building over 12,000 different types of sheds in such a way that anyone can build the shed of their dreams, sans all the frustration and confusion that often comes with most woodworking projects. It’s like a “Building For Dummies” guide that teaches you the accurate steps needed to build everything from a garden shed to a storage shed, greenhouse, and more. So, if you’re tired of finding building plans that are missing steps, that don’t make sense or worse, that don’t accurately list the measurements or tools needed, you need to give Ryan’s Shed Plans a look.
It’s vital to build your shed on a stable, level location—and never in a wet, low-lying area or on a downward slope. And no matter how well a shed is constructed, it won’t hold up on a weak base. A proper foundation is key, one that sets the shed slightly off the ground to aid water drainage and reduce moisture transfer. There are different foundation options, depending on where you live and the size and intended use of the shed, so bone up on the fundamentals and assess your options with this advice from the LP Outdoor Building Solutions team.
Can I tell you a secret? I don’t think I would ever do this again because I have another secret. Shhh, don’t tell, but DIY projects that are a joint effort between my hubby and myself really aren’t fun. They are stressful, and hard and take a toll on us. Which may seem strange in a way because we are both handy and we both enjoy these type of projects and we even have a pretty good idea as to what we are doing. Actually, I think we really have it together – separately! Once you throw the two of us together is gets a little intense. Enough about that, let’s get on to the project.

My Shed Plans just might be every do-it-yourself junkie’s dream product. Ryan Henderson, the creator of My Shed Plans, has been building one-of-a-kind outdoor sheds for more than 20 years. If you believe his story, he has unselfishly decided to share his love of woodworking and carpentry through his guides which will enable the everyman who does not have handyman experience to build their very own outdoor shed. Can it be true?
Woodworking is an art, and like most art forms, it only require dedication, skill and time. Good thing you have our shed plans. You wouldn’t be spending months figuring out how to cut wood pieces, etc. You will get enough guidance to start right away and build a gorgeous shed for your garden. The benefit? You would learn how to build sheds within days. No experiments and no wasting time!

Before a hammer hits a nail: plan, plan, and plan some more. All too often people visit local home centers to get shed ideas. They go inside the prebuilt sheds in the parking lot and decide their own storage needs right then and there. Even worse, they'll grab a few brochures and use those ideas to find a shed design online without doing any proper space planning. 
×