For those considering putting their home on the market soon, it’s likely your looking at what parts of your home to freshen up to impress potential buyers. Changing your cabinet hardware to a traditional option can make a huge difference. Small, ridged handles in a dark finish or square knobs is a cabinet hardware pick that will stand the test of time.
The other option for changing kitchen cabinet knobs is to purchase new ones. The two main types of cabinet fixtures for kitchens are circular pulls and metal bars. The round pulls tend to be old-fashioned, while the metal bar handles are often more contemporary. Cabinet pulls can be made more modern by painting them metallic silver. Metal bar cabinet door handles are usually silver-colored and narrow; this style is often seen with darker wood toned cabinets.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door.
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.
I love to see your work in progress! And I agree that the wood valance over the window looks so much better painted white, you almost don’t see it now. Funny story, I had a similar valance in my last house and as part of my kitchen refresh, I had the contractor knock that out and oh what a difference it made! I had only 1 tiny window in the kitchen and that stinking valance blocked so much light. Your home is much more open and bright with all the white now, thanks for sharing! You’re in the home stretch now!!
I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!
Once you’ve worked out which types of hardware are comfortable to use, it’ll be time to start thinking about shapes in relation to the shape of your cabinetry. In general, knob and pull styles should be matched to kitchen cabinet styles. What this means is if you have selected a plain cabinet style, for example, shaker or flat, ultra-modern doors, then you’ll want square, plain hardware to match — perhaps something like Emtek’s brass bar knob or a similar style. Recessed panel doors or doors with curving and intricate trim will often do well with more ornate hardware styles.
Budget is, of course, a key factor in any part of your kitchen remodeling decisions. While you’ll want to pay as little as possible right now, remember that quality matters in the long run. Your local kitchen cabinet showrooms will offer you the largest variety, with people who can help you choose high-quality hardware within your budget. Remember that the price is based on the finish, as well as the design and size. Knobs are less expensive than pulls.
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
Once you have decided on a style and shape for your hardware, you still need to choose the finish for your knobs and pulls. A shiny chrome finish has a modern feel, while brushed nickel or pewter may bring a more traditional look to your kitchen. Black hardware can be modern in a glossy finish or traditional with a matte finish. Many hardware lines come in several different finishes to help you find exactly the look you want.
For easy access to below-counter drawers and cabinets with minimal aesthetic impact, hidden pulls can be a great option. They’re usually attached to the top edge of each door and designed as small slivers of metal that jut out of the flush portion. They are designed to be largely concealed by the work surface above, forming a subtle lip that does not deter from the material and design of the cabinetry itself.
Wow, love the progress you’ve made ! Thank you so much for these posts , your ideas are wonderful and I love your style. The drawer pulls are lovely, just what I had in mind, but the glass knobs ? What a lovely idea, I have glass knobs on my interior doors, but hadn’t thought of using them on kitchen cabinets . LOVE it . Can’t wait to see the finished kitchen, what an amazing difference .
SimplyBeautifulKitchens.com is a participant in the Amazon Services LLC Associates Program and other affiliate programs, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com and other merchants websites. You should always perform due diligence before buying goods or services online. The Owner does not accept payment or merchandise from manufacturers in exchange for writing reviews.
1. Stick with the theme. The hardware you choose speaks to your theme in the same way your kitchen cabinets do. Which hardware works best with different themes? Sleek, tubular pulls, like those in our Torino collection, complement the streamlined look in modern and contemporary kitchens. Traditional cabinets tend to have more detail and benefit from simple, smooth knobs, like the Projectionin style from our Drake collection. French country can benefit from hardware with an antique look, like our Windermere collection that comes in gun metal, rubbed bronze and brush pewter.
Hardware can have a huge impact on the look and feel of your kitchen, which is why we often recommend replacing hardware as a quick upgrade for rental kitchens, or when you aren’t able to remodel. So when you’re planning a new kitchen, or a re-design, don’t let your hardware be an afterthought. Here are a few guidelines to help you select the right hardware for your kitchen.
Contemporary kitchens have sleek lines, very little ornamentation and minimalistic colors. So, for a contemporary style kitchen, it is wise to choose hardware that is simple and streamlined. Linear bar handles with straight lines or curved barrel handles are the perfect choice. Since stainless steel appliances are a hallmark of a contemporary kitchen, you can also select handles for your cabinetry in a similar style and finish as your appliance handles.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
Let’s talk first about metals. As a general rule, I like to keep the different metals in a kitchen to no more than two. If you have stainless steel appliances, that counts as one metal. So that leaves one other metal you can bring into a kitchen. If you’ve got brass light fixtures, that’s your one other metal. Your new hardware should be nickel or brass.