So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five. I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
Standard hardware is a breeze to install. All you need is a Phillips-Head screwdriver. Simply replace standard screws into the pre-cut holes.If the holes are pre-drilled on your cabinet drawers and you now want to place a single hole, measure the distance between the two holes and center. If your cabinet doesn’t currently have holes or hardware, knowing where to place the different size knobs on each cabinet can be tricky. If there are no holes, and you’re on your own when drilling into the corner of the cabinet door give yourself 2 1/2 to 3″ of space in the corner before you drill in a hole.
Pick a color scheme and stick with it. This tip is twofold, as it helps tremendously in narrowing down your choices while simultaneously expanding your options. Pick a large swath — say, the entire lower half of the kitchen — and commit to a color scheme. If the drawers in your kitchen are white, and all the hardware shares the same type of finish, the presence of different types of knobs and handles will be a pleasant sight, rather than a distraction.
One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.
There are a couple of ways to go about choosing the right color and finish. One school of thought advises you to choose based on the color and finish of the kitchen’s faucet. Given that most faucets are either silver or brass in color, this advice can be limiting, especially if you have your eye on stone knobs or another finish that is not common in faucet design.
As latches like these are elements that people come into contact with every day — literally gripping them for support or activating them with a gentle nudge — architects should keep both aesthetics and functionality in mind when specifying these seemingly simple components. To help you as you search for kitchen hardware on Source, here are a few savvy choices that fit well with modern clean spaces; ones that, even when situated in repetitive rows, won’t take attention away from sleek cabinetry design:
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less. The most common pull sizes for standard cabinetry are 3”, 4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches. Standard knob sizes are less than 1.5 inches in diameter.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
We just moved into our home a few months ago and it definitely needed some updating. We decided to start in the kitchen with new appliances. Black stainless beauties 😍 That's when we really noticed how "80's" our kitchen cabinets were! They were in good shape, just wrong color. So we decided to just paint them! The hinges were terribly dirty with a film over them and brass colored. So here's a step by step how I quickly cleaned them and then painted them to match the black stainless appliances....
- Catches secure the cabinet door using magnets or rollers. - Latches clip or swing into place and are great for homes with children or curious pets. - Drawer Slides make closing and opening drawers easier and self-closing models prevent damage caused by slamming. - Hinges are available in styles and finishes to match cabinet knobs and pulls. Make sure to match the installation type when replacing existing hinges.
Want sleek form? Want functionality at its finest? Say hello to handles. Handles for white cabinets allow a firm and full grip to easily pull open or push close any cabinet door. Handles come in a cornucopia of shapes and sizes to male for a match with your kitchen style. Handles offer installation flexibility, with vertical and horizontal options, which allows for additional detailing for your white cabinets.
Let’s talk first about metals. As a general rule, I like to keep the different metals in a kitchen to no more than two. If you have stainless steel appliances, that counts as one metal. So that leaves one other metal you can bring into a kitchen. If you’ve got brass light fixtures, that’s your one other metal. Your new hardware should be nickel or brass.