Hopefully you drilled for the hinges in the same location on every door, if so, then this should be simple. You really just need to measure for the top hinge. I installed my top hinge 4” down from the top of the door, so I measured 3 ½” down from the inside top of the face frame (3 ½” + ½” overlay = 4”). This step is a team effort, one person to hold the door and another person to attach the hinge to the face frame.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
There is a lot of misunderstanding when it comes to crystal. Upon first glance, it looks like glass, but it is in fact of higher quality and clarity, and its chemical composition is markedly different. Contrary to what its name suggests, crystal is not crystalline on a molecular level — that is, its molecules are not arranged in a rigid, repeating structure.
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.
The chrome and stainless steel can vary some too, but usually not as much, and as often as nickel.  To be safe, get samples from different brands and compare the colors, or get all the hardware that you need for  a single room from one manufacturer.  It’s ok if the nickel in one room doesn’t exactly match the nickel in another room.  It only looks mismatched if the different nickel finishes  are right next to each other in the same room.
I had already chosen polished nickel hardware (which I will share more about soon), so my hinges needed to coordinate.  I decided to use Rub n Buff to give them a much-needed update.  If you don’t know, Rub n Buff is a fantastic metallic paste used to give almost anything a metal finish.  I chose it because it is so easy to use and gives a lasting finish.
You don’t need to match your cabinet hardware finish to the rest of your kitchen. This is one area you can add a little bling. For example, we always recommend chrome faucets because chrome is the most durable (and in our experience, although popular, brushed nickel looks dingy and fingerprints are hard to remove), but consider brushed nickel or champagne gold for your cabinet hardware for a nice juxtaposition of metals in your kitchen
​If you want to use warm metal like matte brass or gold or copper in your house, but are hesitant because you’re afraid it might go out of style in the next few years, adding warm metal cabinet hardware is a great way to go.  If brass, gold and copper do go out of style in the next few years, most cabinet hardware is pretty simple to replace all by yourself.  If, however,  you decide on a warm metal faucets, door hinges or lighting fixtures,  many of us would have to hire a professional or handyman to replace those items.  But cabinet hardware can easily be switch out by almost anyone.  Just make sure you use standard sized hardware.

Some kitchen designs are beginning to display personality through eclectic and artistic approaches to kitchen hardware. Recent trends include nautical-themed rope drawer pulls and door handles, painted designs, numerals, insignias or monograms on drawer pulls. And pulls and handles made from antique buttons, glass or crystal will create a truly unique look that's sure to catch the eye and spark conversation.
It may take some time for you to consider what effect you would like to create with your hardware on your kitchen cabinets. In fact, some styles, patterns, and finishes are so beautiful or unique, that they become the focal point in the kitchen and a topic of conversation. Many of the ceramic and glass styles are so cleverly finished that they look too pretty to simply be part of a kitchen cabinet.

Hardware can have a huge impact on the look and feel of your kitchen, which is why we often recommend replacing hardware as a quick upgrade for rental kitchens, or when you aren’t able to remodel. So when you’re planning a new kitchen, or a re-design, don’t let your hardware be an afterthought. Here are a few guidelines to help you select the right hardware for your kitchen.
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
Ceramic knobs bring such charm to your kitchen. They’re reminiscent of a sweet country cottage, or an old world farm house. It’s not hard to imagine the scent of a freshly baked pie or loaf of bread cooling in the window. Ceramic knobs pair quite nicely with natural wood finishes and glass hutch cabinets. Wether you choose plain white or a funky pattern, ceramic knobs give your kitchen a homey flair.
The chrome and stainless steel can vary some too, but usually not as much, and as often as nickel.  To be safe, get samples from different brands and compare the colors, or get all the hardware that you need for  a single room from one manufacturer.  It’s ok if the nickel in one room doesn’t exactly match the nickel in another room.  It only looks mismatched if the different nickel finishes  are right next to each other in the same room.
What is the existing decor of your kitchen or bathroom? For instance, if your kitchen has a white, Scandinavian minimalist aesthetic, you should try matching your hardware with it — in that case, perhaps something slender, jet-black and low-profile. Mismatching styles can look “off” and can create a confused sense of the room’s personality. However, it can also be done well. We’ll go into more depth on this below.
A good price for pulls begins at around $12.00 a piece because anything less looks cheap and the quality will be sub-par. Look for cabinet hardware at plumbing or cabinet showrooms. They will have a larger variety and better quality. Look through the displays or catalogs and order several samples in different styles and finishes to compare to the rest of the finishes in your kitchen.

Knobs, which are attached with a single screw, are most frequently used on cabinets, and are available with a built-in screw, known as a one-piece knob, or with a separate top and fastener, known as a two-piece design. Modern drawer knobs are made in a variety of materials including brass, zinc, stainless steel (sometimes found in kitchens), bronze, glass, crystal, plastic, wood, and other natural and man-made materials. 
When choosing a backsplash color scheme, keep in mind the type of look you want for your kitchen. By choosing a backsplash color that blends in with your wall color, you’ll be creating a streamlined, coordinated look. If you want to make a statement and have your backsplash pop, try choosing one or even a few colors that accent your wall color, making it stand out from the background.

Remodeling and customizing your kitchen can be a big project. After planning and designing on the large scale it might be tempting to coast through choosing the cabinet hardware, but high-traffic rooms such as kitchens deserve detailed attention. Choosing the right hardware size requires a balance of style and function. Sacrifice one for the other, and you probably won’t be happy. You’ll be frustrated every time you try to pull open a drawer, or you’ll be disappointed every time you walk into the room.
If you’re like me and love hardware (I think of it as jewelry for the house) and want your pulls and knobs to make a statement, instead of blend into background, you’ll want to choose hardware that contrasts with your cabinets, drawers and doors.  Consider using darker finishes like black or oil rubbed bronze on white or light colored cabinets and doors.  
For customers who have homes near the ocean, Cliffside recommends choosing non-metal items such as marble or wood for your projects. Salt air acts as an abrasive, and quickly erodes the lacquer coating. If you absolutely need (or desire) metal hardware, Cliffside recommends solid stainless steel, or certain solid brass finishes such as Black, Polished Brass, or Polished Chrome. Note that, even in optimum indoor conditions, no Cliffside finish has a lifetime guarantee under any circumstances.
Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.
A good price for pulls begins at around $12.00 a piece because anything less looks cheap and the quality will be sub-par. Look for cabinet hardware at plumbing or cabinet showrooms. They will have a larger variety and better quality. Look through the displays or catalogs and order several samples in different styles and finishes to compare to the rest of the finishes in your kitchen.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.

These small items — doorknobs, drawer pulls, cabinet-door handles — are "the jewelry" that can add style and sparkle to any space, says New York-based interior designer Young Huh. Just as the right necklace can turn a simple dress into a fashion statement, a striking new set of knobs on an old cabinet, or vintage crystal doorknobs can bring a huge dose of style to your home with minimal expense, she says.
3. Traditionally, your hardware should be the same finish as your kitchen sink faucet. However, mixing and matching metals is on trend in contemporary and transitional homes. Don’t forget to consider your appliances and light fixtures as well. Black appliances look lovely beside bronze or black hardware, while stainless steel and nickel play nicely together. 
After the center panels have been removed, take measurements of the inside openings. I subtracted an 1/8” from the length and width just to make sure the glass would fit. Now, go to Lowes, find the glass cutting isle and give the kind man or woman working there your list of measurements. Make sure you have other things to shop for because this is going to take a while, but it’s super duper cheap so it’s worth the wait. By the way, you don’t have to use glass, you could use that cool radiator metal, chicken wire, punched tin, you name it, sky’s the limit!
When it comes to finishes, let the rest of the components in the home be your guide. If you are selecting an oil-rubbed bronze artisan faucet, select the matching hardware. Interested in mixing finishes? In today’s home, anything goes. Mixing brass with black iron might be over the top, but pairing brushed nickel with polished chrome can offer a dynamic and attractive contrast.
The other option for changing kitchen cabinet knobs is to purchase new ones. The two main types of cabinet fixtures for kitchens are circular pulls and metal bars. The round pulls tend to be old-fashioned, while the metal bar handles are often more contemporary. Cabinet pulls can be made more modern by painting them metallic silver. Metal bar cabinet door handles are usually silver-colored and narrow; this style is often seen with darker wood toned cabinets.
2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
Picking the perfect cabinets for a project is hard enough, but the effort it takes to research, test and finally decide on the best piece of outward-facing cabinet hardware calls for even further inspection. While the main material for the cabinet door heavily contributes to a kitchen’s character, its hardware serves to accentuate that character further still. A key detail within one of the most important spaces of a residence, cabinet hardware sits squarely at the intersection of form and function, and making the right choice here can elevate the design of the entire kitchen.
Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
Even if you have multiple light fixtures in your kitchen, don’t worry about finding new fixtures that match exactly. By varying the design slightly, each light fixture will stand out and create visual interest in your kitchen. However, when choosing one-off pieces, just be sure to stick with a theme for your lighting so it looks purposeful. In other words, if you’ve picked a rustic metal chandelier for over your dining table, choose something that is also rustic inspired to hang over your kitchen sink, like a simple pendant light, and keep that theme going with other lighting choices as well.

It’s important to choose hardware that will complement the rest of your kitchen décor and accentuate its worthy features. Generally, most people want their cabinet and drawer hardware to coordinate with the handles on their appliances. The colors should work well together, and the finishes shouldn’t clash. Drastically different shapes can also make your kitchen feel cluttered. You should use functionality and your personal preference to approach choosing knobs vs. pulls, but there are a few general guidelines to follow that correlate with your style of cabinets.


The first step in choosing kitchen hardware was to decide on the color and style. I fell in love with the selections offered by Atlas Homewares — so much so that I’m now thrilled to be partnering with them on this post. 🙂  I started by ordering several samples in various shapes, sizes and finishes so I could style them in person with the cabinets and countertops.
Some kitchen designs are beginning to display personality through eclectic and artistic approaches to kitchen hardware. Recent trends include nautical-themed rope drawer pulls and door handles, painted designs, numerals, insignias or monograms on drawer pulls. And pulls and handles made from antique buttons, glass or crystal will create a truly unique look that's sure to catch the eye and spark conversation.
There are a few options for hanging drawer hardware. Usually drawer pulls (or knobs or cup pulls) are centered on the face of the drawer. In a more modern kitchen, you may choose to hang them closer to the top of the face. For Shaker-style drawers, you can hang knobs or pulls either in the center of the drawer OR centered on the top stile. Which look should you go with? Whatever you like the best in your kitchen. Just make sure that you’re consistent across all the drawers. Drawers longer than two feet may look better with two knobs or pulls.

We also did that. Our handles are those stainless steel round bars. Loved the look with our white slab door/drawer fronts! Turned out there was big problem with sides of the horizontal drawer pulls snagging pants pockets. So, replaced those with centered flush type steel rectangular pulls that we mounted on the drawers after using router to make mortise holes No more snagging pockets!
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.
It’s definitely possible to change out the hinges without redoing the cabinets – you would just have to make sure that the holes on the frames where the old hinges were, are able to be filled and touched up so that they’re not obvious. I’m not sure of the cost, but hinges aren’t cheap, and I definitely recommend using a carpenter to do the work. Hinges can be maddening!
Welcome to Willow Lane Cabinetry — the #1 place to buy affordable, semi-custom cabinets online! Let us help you create the kitchen of your dreams with our 100% free kitchen design tool. We offer all wood, semi-custom cabinets, fully assembled and delivered for free. Plus all the accessories you need to complete your remodel. Visit our website to see our products today!
After the center panels have been removed, take measurements of the inside openings. I subtracted an 1/8” from the length and width just to make sure the glass would fit. Now, go to Lowes, find the glass cutting isle and give the kind man or woman working there your list of measurements. Make sure you have other things to shop for because this is going to take a while, but it’s super duper cheap so it’s worth the wait. By the way, you don’t have to use glass, you could use that cool radiator metal, chicken wire, punched tin, you name it, sky’s the limit!
If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.

1. Stick with the theme. The hardware you choose speaks to your theme in the same way your kitchen cabinets do. Which hardware works best with different themes? Sleek, tubular pulls, like those in our Torino collection, complement the streamlined look in modern and contemporary kitchens. Traditional cabinets tend to have more detail and benefit from simple, smooth knobs, like the Projectionin style from our Drake collection. French country can benefit from hardware with an antique look, like our Windermere collection that comes in gun metal, rubbed bronze and brush pewter.
Pulling design from old pharmacies and soda fountains, latch hardware is that without a doubt a nostalgic throwback. Maybe not the most functional if you’re in a hurry, but handy if you’re looking for a little extra security from pets or children. Latches are another hardware type that can easily be mixed and matched, so maybe just keep them to the lesser used cabinets.
Knobs, which are attached with a single screw, are most frequently used on cabinets, and are available with a built-in screw, known as a one-piece knob, or with a separate top and fastener, known as a two-piece design. Modern drawer knobs are made in a variety of materials including brass, zinc, stainless steel (sometimes found in kitchens), bronze, glass, crystal, plastic, wood, and other natural and man-made materials. 
Your kitchen is looking beautiful. White paint is a miracle worker…so are you. I have an old 1970’s GE oven that looks just like yours. It’s a great oven and still works perfectly. I had the door, which was originally light brown, re-enameled years ago when I painted my kitchen white. It’s held up beautifully. I just wish I had two ovens like yours. Sure would come in handy for holiday cooking.
×