One of the first reccomendations I give on choosing hardware, is on wide drawers. Go with a single larger handle especially in the kitchen. The kitchen is a busy area and users find themselves with something in their hand when they go to open a drawer with the free hand. If there are 2 pulls on a drawer, just using one will end up tweaking the drawer in the long run. When I begin to look for a hardware collection always look at the range of sizes in that collection. I like the rule of the larger the drawer the larger the handle... or the more weight the drawer will hold the wider the stance should be that the handle provides.
It may take some time for you to consider what effect you would like to create with your hardware on your kitchen cabinets. In fact, some styles, patterns, and finishes are so beautiful or unique, that they become the focal point in the kitchen and a topic of conversation. Many of the ceramic and glass styles are so cleverly finished that they look too pretty to simply be part of a kitchen cabinet.
3. Know when to use knobs over pulls. In traditional and country kitchens, putting a knob on a cabinet is not uncommon. In fact, with many cabinets, knobs may a better option than pulls. How do you know the difference? When kitchen cabinets are ornate or finely detailed, go with a knob rather than a pull. A knob is smaller and simpler and doesn’t take attention away from the design of the cabinets.
Whereas crystal is made primarily of silica and lead oxide, glass is largely composed of silica and soda lime. The lime is the reason glass can have a greenish tint when light is shining through it, whereas crystal is clear. Glass can provide the perfect accent to a room, and is an excellent secret weapon if you are wondering how to add a “pop” without overdoing it.
Apparently I would use MP(?) kind of boards (I forget what the man at HD called it) and it costs about $25 for an 8x4 sheet. I would just measure my cupboard doors, then go in and tell them the measurements, and they would do all the cutting. Then I would just prime the boards, then paint them, then pre-drill the holes for the new hinges, then put them up.
Cliffside offers a unique brand of stone hardware. The river rock collection is a series of knobs made from river pebbles, which were naturally smoothed by rushing water and by tumbling over each other. They come in shades like gray, salmon-pink, charcoal black, a rusty Martian red and a speckled white that can complement essentially any color scheme imaginable.
Do you dream of a whole-kitchen remodel straight out of a magazine photo spread? Kitchens begin to look dated more quickly than any other room in your home. Replacing cabinets and countertops is an expensive proposition, but what if you could update them just a bit at little cost? Replacing or adding new cabinet hardware is a great way to update your look with the latest finishes and styles, without breaking open the piggy bank.
For customers who have homes near the ocean, Cliffside recommends choosing non-metal items such as marble or wood for your projects. Salt air acts as an abrasive, and quickly erodes the lacquer coating. If you absolutely need (or desire) metal hardware, Cliffside recommends solid stainless steel, or certain solid brass finishes such as Black, Polished Brass, or Polished Chrome. Note that, even in optimum indoor conditions, no Cliffside finish has a lifetime guarantee under any circumstances.
Are your cabinets in good condition but old, worn out and dated looking (kind of like me!)? With just a few tweaks you can bring them into this century and get another 10 to 15 years of life out of them. It seems like back in the 70s and 80s kitchen cabinets were built on site and built to last! That’s the case with the kitchen I’m currently dealing with, the entire kitchen was site built, they made one long face frame for an 8’ bank of cabinets – picture all the face frames of your cabinets connected together and installed as one piece, that’s how this kitchen is. Anyway, I was happy with the layout, it’s pretty basic, so to save some money I decided to work with the existing cabinets by removing the valance, replacing the exposed hinges with concealed hinges and adding glass inserts to the upper, upper cabinets – you’ll see what I mean in a minute. If you have ever thought of updating your dated kitchen cabinets, you’ll definitely want to check out this article in all its splendor.
It’s definitely possible to change out the hinges without redoing the cabinets – you would just have to make sure that the holes on the frames where the old hinges were, are able to be filled and touched up so that they’re not obvious. I’m not sure of the cost, but hinges aren’t cheap, and I definitely recommend using a carpenter to do the work. Hinges can be maddening!
If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.
Hello Mr. TretheweyMy name is terry cotto, when we built our beautiful home 16 years ago, in Sierra Madre Ca I had my claw tub installed,( my child hood remembrance) It appears, that the claw legs of the tub were not installed properly, and one leg fell off , tub was slightly tipping to the right. I had a handyman come over and reinstall the claw legs, tighten so this would not happen again. The other day, while I was bathing I noticed the seal of the drain on the outside rubber was not laying properly, plus it was leaking, ( I think this was due to the leg falling off and unbalancing the ring. Well, now I really don't know what to do about that. I believe the thing to do is remove the cover off the top drain , ok, but than what do I have to move the claw tub, impossible. How do I replace the rubber of the outside of the top drain pipe, it appears to be brittle. (Not good)Please answer my questions, and I will hire the handy man again to help me. Thank you. I have learned so much from T.O.H weekly shows, I am a loyal fan at 75. I tell my 80 year old husband, you need to watch these shows with me, and we can do it ourselves, the right way. God Bless you all for the great job your doing, I need to know how to do it right, so it doesn't happen again. a picture would be good, I can see exactly how its done?
Custom kitchen cabinetry doesn’t come cheap, but if you’re planning to stay put in your home for a long while, it’s worth spending to get exactly what you want, including the built-ins that enable you to live clutter-free. At the other end of the spectrum, we show you ways to modify Ikea kitchen components for a custom look (we’ve found almost a dozen new companies that offer doors to pair with Ikea’s cabinets).
Although kitchen cabinet knobs are small objects, keep in mind that one on each cupboard door creates an overall design impact. Further impact can be created by choosing cabinet knobs that contrast in color and texture with the cabinets. If less impact is desired, cabinet knobs may be made of the same material and in the same color as the kitchen cabinets. The most important thing to remember when choosing cabinet knobs to coordinate with cabinets is to keep the kitchen’s overall tone in mind, whether it’s country, elegant, whimsical or traditional.
Hi Diane, I am so darned impressed with the work you are doing on your kitchen cabinets. We have high end oak cabinets painted in a washed white finish and they need a refresher too. I am going to follow your lead and try and do them myself. I am a novice at this but, you give such excellent instructions that I feel I can do it, starting in January. I want our island to be a dark, almost blue/black finish and the other cupboards done in white. Love yours. I am going to do the counter tops with the paint (Carrara Marble) if I can find it in Canada. I think Home Depot will sell it. I have one big problem. When we originally had our kitchen done back in 1987, they put corrian edging around the edges and I want it taken off. Do you have any suggestions on what to put there to replace it? A friend suggested putting a wood molding there and just painting it too. I just don’t know if it would stand up. Help! Love your great ideas. Thanks so much, Peggy
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door.
Order samples, and get a few different types of styles and sizes to decide what will work best for your cabinet doors. It’s helpful to shop with a sample of your cabinet door. Ask yourself: Does my hand keeps sliding on the grip? Is it difficult to pull or get a grasp on it? Does it get greasy from my fingertips? Would I rather have a pull near the fridge but a knob near the stove? You will use this item a ton of times everyday, and you want to feel comfortable with your choice. There’s nothing worse than a cute knob that’s hard to pull open everyday.