For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
When it comes to designing a kitchen inevitably you have to pick out hardware, and these seemingly small details can literally keep you up at night, going back and forth between brass knobs or stainless steel bars. But thankfully, we’re here to help you get a “handle” on the process. Here are the factors you should consider when choosing kitchen cabinet hardware.
Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
Latches for cabinets aren’t quite as common as they were about a 100 years ago because of improved hinge technology, but you can still find a variety of latches and catches for keeping cabinets closed. A latch is mounted to the outside of a cabinet, and typically features two pieces: a mechanism with a turn or a lever on one side that controls the "tongue" of the latch, and a "shell" with a cavity to house the tongue on the other side. On the other hand, cabinet catches are usually installed on the inside of a cabinet, making them invisible from the exterior, and can consist of a magnet, a clip, or a ball that holds the door closed unless a certain amount of force is applied to open it.
What if you can’t decide on kitchen hardware? It’s OK to mix and match! Pick patterns and finishes that complement each other and install them in a repeating pattern for a look that is custom to your style. It’s easy to switch up this look as you please. However, this might not impress a potential homebuyer if you choose to sell in the future. Consider updating to more traditional cabinet hardware when it comes time to sell.
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.
Sandra, I’m so glad that I came across your blog! You’ve given so much great information that I can use every day in my job doing kitchen cabinet sales. And then there’s the whole DIY part for me personally! I’m really hoping that you can answer my question, though. I have a customer who is refacing her cabinets. She has frameless cabinets and used to have exposed hinges. She wanted concealed hinges so we had the hinge holes drilled 1″ (center) from the edge. She has her new doors but when she hangs them, there’s a 1/4″ gap between the door and center stile, even after adjusting them. We were using full overlay hinges. Can you advise which type of overlay hinge to use and how to rectify the gap? Thanks so much!

Use the same guidelines for or your interior doors. If you like the idea of statement door knobs and hinges, go for lots of contrast— dark door knobs and hinges on light doors, for example.  As an aside, interior door levers, which you simply have to push down, are easier for aging hands to operate as compared to door knobs, which you have to twist.

Once you have decided on a style and shape for your hardware, you still need to choose the finish for your knobs and pulls. A shiny chrome finish has a modern feel, while brushed nickel or pewter may bring a more traditional look to your kitchen. Black hardware can be modern in a glossy finish or traditional with a matte finish. Many hardware lines come in several different finishes to help you find exactly the look you want.
Interior Door knobs and levers can range from less than $20 to $200.  You can find cabinet knobs and pulls from less than $2 each to more than $20 each.     Solid knobs and pulls are better quality than hollow hardware.  Although you generally get what you pay for with hardware, if your budget is tighter, you might want to choose less expensive cabinet hardware since it’s relatively easy for homeowners to trade it out for better quality hardware in the future.
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.

Knikki Grantham is a Trend Manager with over 20 years in the Furniture and in the Furniture and Design Industry. She grew up in the furniture industry with early memories of sawdust and hand tied springs. After working in various phases of furniture production and development she moved into Design Sales for a Luxury high-end retailer, attaining an Associate ASID as well as other accreditations from various furniture manufacturers.
“What is your overall style? Traditional, contemporary, arts and crafts, eclectic, cottage, French, Mediterranean, Western, Art Deco or coastal,” asks Brandino Brass co-owner Eric Brandino. He encourages clients to think about the style of their home or the style they would like to incorporate. “Is there a consistent style throughout or does it vary from room to room? Transitional style has been one of the most popular looks recently,” he says of what’s trending in hardware. “Clean lines with just a touch of traditional features and finishes, such as an unlacquered brass or bronze.”
Remodeling and customizing your kitchen can be a big project. After planning and designing on the large scale it might be tempting to coast through choosing the cabinet hardware, but high-traffic rooms such as kitchens deserve detailed attention. Choosing the right hardware size requires a balance of style and function. Sacrifice one for the other, and you probably won’t be happy. You’ll be frustrated every time you try to pull open a drawer, or you’ll be disappointed every time you walk into the room.

Due to its quasi-metallic makeup, crystal does much more than just sparkle — it also exhibits other coveted traits. When rubbed to the point of vibrating, crystal will produce a musical tone. It is also stronger than glass and can be blown quite thin. Cliffside Industries distributes German crystal, which is stupendous in its clarity and diamond-like cuts, as well as products from the world-famous Austrian crystal maker Swarovski AG.
Over time, switch plates and outlet covers can become dingy and dirty. Replacing your old outlet covers is a quick way to add some new life to your kitchen décor. Switch plates and outlet covers are no longer stuck just being basic functional pieces on your wall. There are many different designs, materials and finishes that can complement the look of any room. Choose switch plates and outlet covers that are made from high-quality metal materials because they are more durable and stylish than basic plastic ones. Plus, you won’t have to worry about kitchen splatter creating unsightly stains on your covers, as this material is super easy to wipe clean!

Consider the style that you have used to decorate your home. Traditional styling indicates a need to use cabinet hardware that has a brushed finish. Pewter, nickel, and polished brass blend well with traditional styling, although other styles will look nice as well. Perhaps you would prefer to contrast the traditional cabinets with some hardware that leans more toward the unique and modern.

Under-cabinet lighting serves not only a fashionable purpose by creating visual depth in your kitchen, but it serves a functional purpose as well. The added lighting will make everything from chopping veggies to reading recipes to measuring ingredients easier to see as your countertops will be under direct light from above. And as far as style goes, the right lighting can make all the difference!

Updating certain hardware pieces throughout your kitchen is a simple change that can have a big impact on the overall look of your kitchen. Replacing basic ceramic or plastic knobs on your cabinets with heavy-duty stainless steel or brass knobs can give your kitchen cabinets a whole new refreshed style. Depending on the look you’re trying to achieve in your kitchen, you’ll find metal cabinet knobs that range in aesthetics from simple and contemporary, to ornate and decorative.


Hi Diane, I am so darned impressed with the work you are doing on your kitchen cabinets. We have high end oak cabinets painted in a washed white finish and they need a refresher too. I am going to follow your lead and try and do them myself. I am a novice at this but, you give such excellent instructions that I feel I can do it, starting in January. I want our island to be a dark, almost blue/black finish and the other cupboards done in white. Love yours. I am going to do the counter tops with the paint (Carrara Marble) if I can find it in Canada. I think Home Depot will sell it. I have one big problem. When we originally had our kitchen done back in 1987, they put corrian edging around the edges and I want it taken off. Do you have any suggestions on what to put there to replace it? A friend suggested putting a wood molding there and just painting it too. I just don’t know if it would stand up. Help! Love your great ideas. Thanks so much, Peggy
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.
Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.
Shaker style cabinets. The most common style of cabinet offers flexibility in design, and they work well with knobs or cup or bin pulls. Shakers are known for their simplicity and clean lines, so simple hardware is often used, such as round knobs.Traditional nickel or steel knobs or pulls are common, as well as vintage glass or ceramic knobs. Vintage pulls with exposed screws provide a classic touch or industrial feel to a new kitchen with shaker cabinets. Tubular bar pulls — which can be short or long and dramatic — modernize a traditional kitchen with shaker cabinets. Flat bar pulls offer a contemporary edge, while wire pulls keep your décor traditional. Arched and footed bar pulls offer a classic look on shaker style cabinets.
Specializing in hardwood furniture, trim carpentry, cabinets, home improvement and architectural millwork, Wade Shaddy has worked in homebuilding since 1972. Shaddy has also worked as a newspaper reporter and writer, and as a contributing writer for Bicycling Magazine. Shaddy began publishing in various magazines in 1992, and published a novel, “Dark Canyon,” in 2008.
For oversized cabinetry you’ll obviously want to use larger hardware.  Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized.  For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches.  Some contemporary pulls are even larger than 12 inches.  That measurement is taken from the center of one screw hole to the center of the second screw hole).  Oversized knobs  are 1-1/2” or larger.
2. Keep finishes cohesive. You’ll find hardware in a range of finishes from brushed nickel to brass. While mixing and matching the hardware around your kitchen is fine, you should try to maintain the same finish and keep colors as close as possible. Sometimes you’re forced to buy hardware from more than one retailer, but when doing so make sure you keep finishes cohesive.
As latches like these are elements that people come into contact with every day — literally gripping them for support or activating them with a gentle nudge — architects should keep both aesthetics and functionality in mind when specifying these seemingly simple components. To help you as you search for kitchen hardware on Source, here are a few savvy choices that fit well with modern clean spaces; ones that, even when situated in repetitive rows, won’t take attention away from sleek cabinetry design:

I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!
Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.

- Catches secure the cabinet door using magnets or rollers. - Latches clip or swing into place and are great for homes with children or curious pets. - Drawer Slides make closing and opening drawers easier and self-closing models prevent damage caused by slamming. - Hinges are available in styles and finishes to match cabinet knobs and pulls. Make sure to match the installation type when replacing existing hinges.
What they are: Sturdy yet glamorous pulls that complement many styles of cabinetry. Here linear flat bar pulls not only underscore the contemporary feel of the kitchen, but oversize pulls eliminate the need for two pulls on a wide drawer. A good rule of thumb is to use two knobs or pulls on drawers 18 inches wide or wider. But if you choose superwide pulls like these, one is enough.
Updating the hardware on your kitchen windows can take them from standard to standout in seconds! Typically, window sash locks and lift pulls blend in with your window color, but switching these traditional styles up with an elegant bronze or a satin nickel finish will add interest and pizzazz to your windows. You can also choose a finish that matches the rest of your kitchen hardware for a pulled together style.
Consider the style that you have used to decorate your home. Traditional styling indicates a need to use cabinet hardware that has a brushed finish. Pewter, nickel, and polished brass blend well with traditional styling, although other styles will look nice as well. Perhaps you would prefer to contrast the traditional cabinets with some hardware that leans more toward the unique and modern.
Over time, switch plates and outlet covers can become dingy and dirty. Replacing your old outlet covers is a quick way to add some new life to your kitchen décor. Switch plates and outlet covers are no longer stuck just being basic functional pieces on your wall. There are many different designs, materials and finishes that can complement the look of any room. Choose switch plates and outlet covers that are made from high-quality metal materials because they are more durable and stylish than basic plastic ones. Plus, you won’t have to worry about kitchen splatter creating unsightly stains on your covers, as this material is super easy to wipe clean!
5. Be aware of the appliances and fixtures in the kitchen. Pulls and knobs are not the only hardware in your kitchen. Take into account the finish on appliances, light fixtures, and your sink and faucet. While mixing metal finishes is trendy right now in kitchen design, be sure not to overdo it. If the colors clash, it could disrupt the cohesiveness of your kitchen and take away from the beauty of your new cabinets.
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
Concealed hinges can be mounted on the surface of the door or a pressed into a “cup” that is drilled into the door.  These are often called “cup hinges”.  The cup diameter is generally 35mm but that can vary as can the drill depth required to accept the hinge.  Most concealed hinges have built in adjustability so you can slightly change the position of the door without relocating the hinge.
Although kitchen cabinet knobs are small objects, keep in mind that one on each cupboard door creates an overall design impact. Further impact can be created by choosing cabinet knobs that contrast in color and texture with the cabinets. If less impact is desired, cabinet knobs may be made of the same material and in the same color as the kitchen cabinets. The most important thing to remember when choosing cabinet knobs to coordinate with cabinets is to keep the kitchen’s overall tone in mind, whether it’s country, elegant, whimsical or traditional.

Though not as common as stainless steel or brass, pewter is a very traditional western metal to use in a kitchen. It has a long history dating back around a thousand years — the “Worshipful Company of Pewterers” was even formed in 14th-century England to regulate pewter quality. By the time it began making its way onto furniture in the 1700s, it was a centuries-old art.
“People come in and say they have a ‘standard’ door,” says Renee Genereux of the Brandino Brass team. “But there is no such thing as standard. You need to know your door thickness, how does it swing, what’s the width, what kind of holes do you have.” Avoid multiple visits to the hardware store because you don’t have all of the information and measurements you need. “We give them all of the questions to answer and then they come back with all of it.” Call Brandino Brass ahead of time to ask what you need to know for your visit or check out the sheet below as handy guideline for getting to know your doors and cabinets better.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
The size of your cabinets will influence the size of your knobs. If your cabinets are smaller in scale you’ll want to opt for hardware that is likewise, such as minimal-scale circular knobs. Longer hardware is necessary when you have extra long cabinet doors—or can be used if you want to make a more of dramatic statement. Most cabinet doors are 24”, so you want a knob about 2”-3” size knob. For a larger cabinet door you can size up to 3½” or 4”. For a cabinet door under 20”, source hardware that’s closer to 1” to 2” size in diameter or length.
×