Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less. The most common pull sizes for standard cabinetry are 3”, 4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches. Standard knob sizes are less than 1.5 inches in diameter.
Recessed Pulls mimic the utilitarian style of traditional office cabinetry. They’re built into the cabinet door and can be crafted from the same material to blend in or a contrasting material to highlight their presence. They’re also great for high-traffic kitchens because they don’t protrude from the doors, meaning there is little risk of them snagging on clothing.
Swapping these items out is often easy, and Los Angeles-based designer Betsy Burnham says her clients are frequently surprised at the visual impact of something as simple as carefully chosen hardware. Last summer, she added door pulls made of rope tied in small nautical knots to the built-in cabinets at a California beach house, inexpensively adding a dash of personality to the space.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening.
If you have a removable island or a butcher block in your kitchen, an easy way to make that extra piece look cohesive with the rest of your kitchen décor is by adding coordinating cup and cabinet pulls to drawers and doors. This addition will make your island look purposeful and blend it with the rest of your kitchen cabinets — even if the finish or countertop is different.
The quick answer is yes, you can change the hinges. The hard part is what type. Cabinet doors have lots of different configurations.....full overlay, partial overlay, inset, etc., etc. The hinges have to fit the door style. There are hidden hinges that screw to the cabinet framework without major holes, and there are European type hinges that require a large hole to set the hinge into. Go to big box and look at the hinges, what is available can be mind boggling, until you understand the type of door you have.
Cabinetmaker Steve Roca replies: Whether you're hanging new doors, as I'm doing here for a hallway cabinet, or swapping out old hinges, concealed or Euro-style hinges are a dream to install. Unlike the butt or knife hinges often used in kitchen cabinets, they can be adjusted along three axes with the turn of a screwdriver, so you can easily fine-tune the door's fit.
I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
The next step was to decide whether to go with pulls, knobs, or a combination of the two– and also the size. THIS WILL SEND YOU TO THE MADHOUSE if you’re not careful. To make my decision easier, I perused my kitchen ideas board on Pinterest and realized the look I was going for was modern and symmetrical– and many of the modern kitchen used only pulls, not knobs. Hmmmm, this was interesting. Maybe it wasn’t so hard to choose?
Order samples, and get a few different types of styles and sizes to decide what will work best for your cabinet doors. It’s helpful to shop with a sample of your cabinet door. Ask yourself: Does my hand keeps sliding on the grip? Is it difficult to pull or get a grasp on it? Does it get greasy from my fingertips? Would I rather have a pull near the fridge but a knob near the stove? You will use this item a ton of times everyday, and you want to feel comfortable with your choice. There’s nothing worse than a cute knob that’s hard to pull open everyday.
The first step in choosing kitchen hardware was to decide on the color and style. I fell in love with the selections offered by Atlas Homewares — so much so that I’m now thrilled to be partnering with them on this post. 🙂 I started by ordering several samples in various shapes, sizes and finishes so I could style them in person with the cabinets and countertops.
Kitchen cabinet knobs can really change the look of your cabinets. The best knobs and handles not only suit the cabinet style, but also add to the theme or mood of your kitchen. For example, the warm appeal of hammered copper cupboard handles blends well with rustic kitchens, while the cool sparkle of crystal knobs looks elegant against dark wood cabinets.
I’m Jenny, a wife of 23 years, mother of three, and a corporate drop-out. I’m a creative minded blogger, business owner and DIYer, and love transforming furniture, cabinets and rooms in my home. I’m a card carrying paint geek, and am always amazed at the power of paint in making budget-friendly updates to your home. I’m a serial house-stalker, and never tire of a great home tour or a before and after renovation. I’m a firm believer in restyling, refreshing and renewing things in your home to make it your own - without breaking the budget. I’ll show you how!
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
Chrome, nickel and stainless steel finishes will never go out of style, but warm metallics offer a fresh, modern look. For a quick update, consider replacing your lighting, faucet or cabinet hardware with products in gleaming brass or bronze like the ones in this chic space. “The updated satin brass cabinet hardware is really striking against the simple shaker cabinets,” says designer Elizabeth Lawson.