This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less.   The most common pull sizes for standard cabinetry are 3”,  4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches.  Standard knob sizes are less than 1.5 inches in diameter.

2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
But If you don’t think of your hardware as decorative (but as purely functional) and just want your pulls and knobs to blend into the background, instead of standing out, you can choose hardware that is more subtle.  Choose dark hardware for darker cabinets or silver or clear hardware for white or light cabinets.   Alternatively, you can forgo cabinet pulls and knobs all together, which will give a much more contemporary  look.
Thank you so much for helping me understand more about the process to choose new kitchen cabinet hardware. We have been really into rustic looking kitchens lately, and I think that some antique decorative nails could really change the way it looks. Just as you mentioned, you can always change the look of your kitchen again if you do not like the way it looks after a couple of years. Thanks for posting!
Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.

Some styles of kitchen cabinets are designed to open at the side of the door, so they don’t have outer knobs. When re-facing cupboard doors as part of a remodeling project, new knobs can still be added to these self-opening styles. Consider adding knobs or handles that create visual interest. Careful planning is needed as holes will need to be drilled in the cabinet doors to add the new knobs.


There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.
When decorating your rustic kitchen, a little bit of detail can go along way! There are many round, cast iron options that have designs that look great in rustic kitchens. If cast iron is too dark for your cabinets, look for an antique pewter finish. The detail within the hardware itself will certainly add to the look. This option also works well for a farmhouse style kitchen, giving it a great country feel.
Choose hardware that will contrast with your cabinets. Accent dark wood with brass, stainless steel, chrome or nickel. Light-colored cabinets provide the perfect background for bronze, enamel or copper with an antique finish. Metal hardware with a satin or highly polished finish can be adapted to a contemporary or traditional decor. Oil-rubbed bronze suggests a more casual style. Consider enamel and glass hardware for a Victorian home. Glass is also available in sleek designs to accent a contemporary setting.

Hopefully you drilled for the hinges in the same location on every door, if so, then this should be simple. You really just need to measure for the top hinge. I installed my top hinge 4” down from the top of the door, so I measured 3 ½” down from the inside top of the face frame (3 ½” + ½” overlay = 4”). This step is a team effort, one person to hold the door and another person to attach the hinge to the face frame.
Most knobs and pulls are only a few dollars apiece but when you consider the sheer number that you’ll need, those costs add up fast. For each standard lower cabinet with two doors and one drawer, you’ll need three pieces of hardware — and two more knobs or pulls for the matching upper cabinet doors. With that in mind, here are a couple of factors to consider:
Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.

If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.
Hidden hinges also come in a soft-close style if you’re one of those people who want the latest and greatest. (Is it really that bad to hear a door close?) My new cabinets came with soft close hinges that I personally could take or leave.  I still find myself trying to shut them all the way instead of letting them do their thing. You might not want soft-close hinges if you’re the type who likes to slam things when irritated. (Just a thought.)
When exploring kitchen cabinet hardware ideas, your first task should be to decide how closely aligned in terms of style you want your hardware and the cabinets themselves. For example, a traditional Shaker style cabinet can be complemented with simple, understated brushed metal hardware—or it can provide a blank canvas for all manner of creative approaches to door handles and drawer pulls. The choice is yours, and while it's true that sticking with a one-to-one approach with cabinets and hardware may save you time and simplify the design process, exploring other options may allow you to express more of your own design aesthetic in the kitchen.
The type of knob that works best in a kitchen will range in size and style depending on the color and type of cabinetry you have (which is also why so many people go with simple white cabinets in their kitchens!). Knobs also come in a range of shapes and sizes, but are often designed for comfort and ergonomics, so there are rarely sharp edges that could potentially hurt someone pulling on it.

Generally speaking, I like to see a combination of knobs and handles/pulls. Knobs or handles for the doors and handles or pulls for the drawers. If you are painting your kitchen, the extra holes can be filled, sanded, and smoothed prior to painting so you can start with a clean slate and choose any hardware for your update. I say “generally speaking” because lately I’m drawn to kitchens that have all handles like this “before” photo of a kitchen we recently updated.
×