​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.
Latches for cabinets aren’t quite as common as they were about a 100 years ago because of improved hinge technology, but you can still find a variety of latches and catches for keeping cabinets closed. A latch is mounted to the outside of a cabinet, and typically features two pieces: a mechanism with a turn or a lever on one side that controls the "tongue" of the latch, and a "shell" with a cavity to house the tongue on the other side. On the other hand, cabinet catches are usually installed on the inside of a cabinet, making them invisible from the exterior, and can consist of a magnet, a clip, or a ball that holds the door closed unless a certain amount of force is applied to open it.
Flat-panel cabinets.Most often seen in modern or contemporary kitchens, flat-panel cabinets embrace minimal embellishment to focus on natural materials. Subtle hardware choices are best, such as stainless steel bar pulls. You often see long, extended versions placed on the door or drawer.If you prefer square edges, you can choose a flat bar pull. Recessed pulls offer a functional option that work especially well for high-traffic kitchens. If you’re aiming for a minimalist look to your kitchen, you might consider discreet tab pulls for your flat-style cabinets.
By adding hardware you like, you’re literally installing your style into the room — and this will make any accessories you want to add in feel like a part of the kitchen’s design, and not out of place. Of course, not every cabinet + hardware combo is going to work, but see how far you can take it when it comes to choosing hardware outside the traditional style of the cabinets.

The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.


Knobs have been around forever, and still function as a clean and classic hardware, with loads of practicality. Especially for cabinets that get used the most, knobs are still a perfect fit. Pay close attention to the color and size of knobs for white cabinets, and also be mindful of the finish. Are you looking for a shiny finish to match your white, modern kitchen? Or perhaps you prefer a matte finish, to accentuate your country style kitchen.

Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.

Hidden hinges, or European (Euro) hinges as they’re called, aren’t difficult to install, and were part of my mini kitchen update. My kitchen is small, and in order to gain storage space, I switched the 30″ upper cabinets to 42″ ones, but kept some of the existing base cabinets. The very shiny, visible hinges on the base cabinets were a dead giveaway as to which cabinets were the moldy oldies. Here are the originals.
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less.   The most common pull sizes for standard cabinetry are 3”,  4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches.  Standard knob sizes are less than 1.5 inches in diameter.
These small items — doorknobs, drawer pulls, cabinet-door handles — are "the jewelry" that can add style and sparkle to any space, says New York-based interior designer Young Huh. Just as the right necklace can turn a simple dress into a fashion statement, a striking new set of knobs on an old cabinet, or vintage crystal doorknobs can bring a huge dose of style to your home with minimal expense, she says.

Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.

Dreamy DIY: Have you ever seen something that makes you want to break out the craft kit and get to down to business? Well these leather drawer pulls with brass rivets are so luxuriously handsome it makes us want to rip out and redo every single pull in the house. I can only imagine how delightful these will begin to look when worn with use — a little imperfection to balance and roughen up such a posh space.
×