Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
What if you can’t decide on kitchen hardware? It’s OK to mix and match! Pick patterns and finishes that complement each other and install them in a repeating pattern for a look that is custom to your style. It’s easy to switch up this look as you please. However, this might not impress a potential homebuyer if you choose to sell in the future. Consider updating to more traditional cabinet hardware when it comes time to sell.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door.
Though not as common as stainless steel or brass, pewter is a very traditional western metal to use in a kitchen. It has a long history dating back around a thousand years — the “Worshipful Company of Pewterers” was even formed in 14th-century England to regulate pewter quality. By the time it began making its way onto furniture in the 1700s, it was a centuries-old art.
Pick a color scheme and stick with it. This tip is twofold, as it helps tremendously in narrowing down your choices while simultaneously expanding your options. Pick a large swath — say, the entire lower half of the kitchen — and commit to a color scheme. If the drawers in your kitchen are white, and all the hardware shares the same type of finish, the presence of different types of knobs and handles will be a pleasant sight, rather than a distraction.
After the center panels have been removed, take measurements of the inside openings. I subtracted an 1/8” from the length and width just to make sure the glass would fit. Now, go to Lowes, find the glass cutting isle and give the kind man or woman working there your list of measurements. Make sure you have other things to shop for because this is going to take a while, but it’s super duper cheap so it’s worth the wait. By the way, you don’t have to use glass, you could use that cool radiator metal, chicken wire, punched tin, you name it, sky’s the limit!
Kitchen renovation is one of the important part of your kitchen. But for this first you should make a plan, after that decide the budget. There are variety of flooring materials and from this you should select one according to your needs and preferences. Then select the kitchen cabinet hardware. For this you should decide which design you want to select, then select the size and shape of the material. In your blog you give the clear idea on how to select the kitchen cabinet hardware. You can refer this: https://kitchenemp.net/kitchens/
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.
Prevent cabinet doors from slamming shut with integrated Prevent cabinet doors from slamming shut with integrated soft-close technology from Everbilt. Designed for a full overlay these hinges are retro fit able and allow any level DIYer to do away with the heavy slamming of cabinet doors. The complete overlay leaves your cabinets with a sleek modern look. More + Product Details Close
Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
I love your site and your super helpful advice. We’re installing full overlay cabinets in our kitchen and we’re trying to select hinges for the upper cabinets — particularly the cupboard doors on the end which when closed is perpendicular to a wall. Since the door aren’t inset, I’m concerned we won’t be able to open the cupboard a full 90 degrees. Basically, the issue is how to solve the problem of the door swing? Are there any hinges that could solve this problem? I can send elevations if that helps. Thanks so much in advance!
Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five. I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
My home was built in 1940 and the kitchen cabinet hinges and pulls are the hammered black ones. I want to replace same pulls with chrome or polished chrome but cannot find the offset hinges or pulls to fit the holes. I really do not want to have to fill the holes to get another kind. Where can I find these? Have seen them in the past but now I cannot find them. Where should I look?
Rest easy, friends, you can do this, too. And then, since it looks much better and you are thrilled and at peace with it, you can move on to dreaming about that full kitchen reno you are still working towards… one day. Or, maybe you will be so happy with the small changes you made that you can cross that idea right off the list and move on to dreaming about making other areas of your home just right.
Oh how true this is for me right now. Oh how true. Luckily I’m here :-). By the way, I can’t handle your kitchen, it’s too perfect. I’ve never seen anything like it and it’s the best thing I’ve ever seen. I’m doing a modern eclectic boho kitchen, predominately white, some wood accents, maybe darker lower cabinets, maybe gold hardware (that’s where I’m stuck), and then pops of beautiful colour like you have here. I’m excited!
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
And then there’s appliance hardware. Appliance pulls are not just hardware pulls that have a higher price point. It is a more durable hardware that look identical in style to your standard pulls, but are designed for the larger items in your kitchen like refrigerators, dishwashers, pantries, and oversized drawers. They come in a range of sizes from 6” to 36” and are constructed to hold a heavier weight, typically necessitating longer screws and a backplate for installation. The screws can be shortened to the needed size, but its best to follow the instructions and have these pieces installed by a professional to avoid hiccups.