When you’re choosing cabinet hardware, think about the number of times you’ll touch these pieces every day. If your cabinet pulls look and feel good and function well, you’re sure to derive pleasure from them. Browse our narrowed-down choices, from modern cabinet pulls to traditional knobs. Simply replacing your cabinet knobs is the easiest (and cheapest) way to spiff up a kitchen. Get started here.
Cabinet hardware sizes can vary depending on your own personal design preferences, but you’ll want to choose a size that is both stylish and functional. Bar pull sizes are generally determined by the “center-to-center” measurement (the distance between the two screw holes). If you have pre-drilled cabinetry, you’ll need to buy hardware that fits the existing center-to-center measurement. Otherwise, you’re left to your own devices in choosing the size of your cabinet hardware. Here are a few general guidelines to follow:
The next step was to decide whether to go with pulls, knobs, or a combination of the two– and also the size. THIS WILL SEND YOU TO THE MADHOUSE if you’re not careful. To make my decision easier, I perused my kitchen ideas board on Pinterest and realized the look I was going for was modern and symmetrical– and many of the modern kitchen used only pulls, not knobs. Hmmmm, this was interesting. Maybe it wasn’t so hard to choose?
You may also have seen cabinets that are so modern and minimalist that they have no knobs or pulls whatsoever—and they look like they’re impossible to open! The trick is, in fact, a mechanism with a spring located on the inside of the cabinet. When you push on the corner of a cabinet, you compress and then release the spring, which in turn pops the cabinet open. In order to close the cabinet, you simply push it closed until you hear the little "click" that means the spring is back in its locked position.

Below and above the sink can be two different color schemes. Don’t worry, you can mix and match more than you might think and still obey the laws of symmetry. It can provide a sunny, uplifting splash to have a lighter color above the level of the countertops, such as a warm brass or gold. Particularly with items like faucets and sconces, a lighter color around eye level will create a happy glow.


For customers who have homes near the ocean, Cliffside recommends choosing non-metal items such as marble or wood for your projects. Salt air acts as an abrasive, and quickly erodes the lacquer coating. If you absolutely need (or desire) metal hardware, Cliffside recommends solid stainless steel, or certain solid brass finishes such as Black, Polished Brass, or Polished Chrome. Note that, even in optimum indoor conditions, no Cliffside finish has a lifetime guarantee under any circumstances.

Interior Door knobs and levers can range from less than $20 to $200.  You can find cabinet knobs and pulls from less than $2 each to more than $20 each.     Solid knobs and pulls are better quality than hollow hardware.  Although you generally get what you pay for with hardware, if your budget is tighter, you might want to choose less expensive cabinet hardware since it’s relatively easy for homeowners to trade it out for better quality hardware in the future.


Traditional style cabinetry typically has elaborate detailing, embellishments and moldings. Decorative, ornate hardware is in keeping with this style. Often, interior designers choose drop handles for traditional style doors with coordinating knobs on the drawers. Want a vintage look? Try a handle with a porcelain overlay for a sophisticated farmhouse feel. 
Prior to making the purchase of your new cabinet hardware, take some careful measurements of the existing hardware. Write down sizes, as well as the spacing of the screws. This should eliminate the need to drill new holes. Accurate measurements are essential to avoid additional work or the need to return and exchange your hardware purchase. In fact, it is a good idea to bring some of your old hardware with you for size comparison purposes, unless you are shopping online for your hardware. In that case, simply have the hardware next to you.

I would like to use a hinge similar to the wrap around no mortise Amaroc 3175s but am disappointed to learn the poor reviews ….sloppy….bent…flimsy…not worth it…low qc import. Perhaps they were better in the past! I would be most greatful if you could recommend a better quality hinge of that style. Alternatively,Can the full inset euro cup hinge be adapted to a face frame cabinet by building out the inside lip ^
Even if you have multiple light fixtures in your kitchen, don’t worry about finding new fixtures that match exactly. By varying the design slightly, each light fixture will stand out and create visual interest in your kitchen. However, when choosing one-off pieces, just be sure to stick with a theme for your lighting so it looks purposeful. In other words, if you’ve picked a rustic metal chandelier for over your dining table, choose something that is also rustic inspired to hang over your kitchen sink, like a simple pendant light, and keep that theme going with other lighting choices as well.
Cliffside offers a unique brand of stone hardware. The river rock collection is a series of knobs made from river pebbles, which were naturally smoothed by rushing water and by tumbling over each other. They come in shades like gray, salmon-pink, charcoal black, a rusty Martian red and a speckled white that can complement essentially any color scheme imaginable.
Sandra, thank you so much for this awesome post! I’m remodeling my 40 yr old kitchen, and wanted to get rid of the visible old fashioned hinges that show! I had absolutely no clue as to what type of cabinets I have until I read your post! I completely understand now, and will be purchasing the “concealed surface mount overlay hinges for face frame cabinets” I know the 3 holes on the outside will be visible when I change out the hinges, so I’ll just fill them in with wood filler and sand before repainting. You’re so smart, informative and detail oriented just like me! Thank you again so much for this wonderful lesson on cabinets and hinges! I’m subscribing to your website or blog or whatever you have!

Based on the size of the room, consider how much leeway you have to mix different finishes and materials. Mixing finishes can add a classic agelessness to a room, but the smaller the room is, the more carefully one must tread when doing so. If there are too many different finishes in one small space, you run the risk of having your hardware look random and noncommital. However, if you select each piece carefully, it can add warmth and a sense of human touch — subconsciously giving the impression that the collection was acquired over time.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Latches for cabinets aren’t quite as common as they were about a 100 years ago because of improved hinge technology, but you can still find a variety of latches and catches for keeping cabinets closed. A latch is mounted to the outside of a cabinet, and typically features two pieces: a mechanism with a turn or a lever on one side that controls the "tongue" of the latch, and a "shell" with a cavity to house the tongue on the other side. On the other hand, cabinet catches are usually installed on the inside of a cabinet, making them invisible from the exterior, and can consist of a magnet, a clip, or a ball that holds the door closed unless a certain amount of force is applied to open it.
Wow! I finally figured out what to ask for, THANKS. Old hickory cabinets still look great, and the wife loves them, but hates the sound of them closing. Want soft closing hinges, a nice project. They are face-frame cabinets, with semi-inset doors with about 1/4″ overlay.and inset about 3/8″. What hinges do I need? Plan on doing this just as soon as the soft closing drawer slides are all installed.
What they are: Sturdy yet glamorous pulls that complement many styles of cabinetry. Here linear flat bar pulls not only underscore the contemporary feel of the kitchen, but oversize pulls eliminate the need for two pulls on a wide drawer. A good rule of thumb is to use two knobs or pulls on drawers 18 inches wide or wider. But if you choose superwide pulls like these, one is enough.
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
Furthermore, hardware attracts the eye like a bright light. Functionality aside, it is the ultimate accent piece — it provides a pop to cabinets and drawers that can make or break the décor of a room. It also keeps the wood of our cabinets and drawers looking fresh by taking the brunt of the natural oils in our hands, which we leave behind every time we reach for the cabinet to grab something.
Sandra, I’m so glad that I came across your blog! You’ve given so much great information that I can use every day in my job doing kitchen cabinet sales. And then there’s the whole DIY part for me personally! I’m really hoping that you can answer my question, though. I have a customer who is refacing her cabinets. She has frameless cabinets and used to have exposed hinges. She wanted concealed hinges so we had the hinge holes drilled 1″ (center) from the edge. She has her new doors but when she hangs them, there’s a 1/4″ gap between the door and center stile, even after adjusting them. We were using full overlay hinges. Can you advise which type of overlay hinge to use and how to rectify the gap? Thanks so much!
“People come in and say they have a ‘standard’ door,” says Renee Genereux of the Brandino Brass team. “But there is no such thing as standard. You need to know your door thickness, how does it swing, what’s the width, what kind of holes do you have.” Avoid multiple visits to the hardware store because you don’t have all of the information and measurements you need. “We give them all of the questions to answer and then they come back with all of it.” Call Brandino Brass ahead of time to ask what you need to know for your visit or check out the sheet below as handy guideline for getting to know your doors and cabinets better.
Under-cabinet lighting serves not only a fashionable purpose by creating visual depth in your kitchen, but it serves a functional purpose as well. The added lighting will make everything from chopping veggies to reading recipes to measuring ingredients easier to see as your countertops will be under direct light from above. And as far as style goes, the right lighting can make all the difference!
Welcome to Willow Lane Cabinetry — the #1 place to buy affordable, semi-custom cabinets online! Let us help you create the kitchen of your dreams with our 100% free kitchen design tool. We offer all wood, semi-custom cabinets, fully assembled and delivered for free. Plus all the accessories you need to complete your remodel. Visit our website to see our products today!

Accessorizing is the most important part of any outfit. A little glimmer, a little glam or maybe something unexpected and modern can make an ensemble. Well, I think that accessorizing happens to be just as important when decorating your home, which is why we’re exploring the “jewelry options” for the kitchen: hardware! Often overlooked, but capable of extreme 'wow' factor, the pulls on our cupboards can easily be swapped out to drastically change the style of your space.
×