Here are the three different kinds of kitchen cabinet doors that demonstrate the different overlays and hinge options. The first is similar to what I’m working on now – a framed cabinet with an overlay on the cabinet frame. The second is a framed cabinet where the doors are inset, flush with the cabinet frame. And the third is a frameless cabinet where hidden hinges are utilized.
2. Keep finishes cohesive. You’ll find hardware in a range of finishes from brushed nickel to brass. While mixing and matching the hardware around your kitchen is fine, you should try to maintain the same finish and keep colors as close as possible. Sometimes you’re forced to buy hardware from more than one retailer, but when doing so make sure you keep finishes cohesive.
Choosing your kitchen hardware is a great way to customize the look of your cabinetry and drawers. From pulls to knobs and handles, you can get your kitchen cabinet hardware in almost any shape you desire. Choosing the right shape mainly depends on personal preference. I once had handles that we’re a bit snug on my finger when I opened a cabinet. As a result, every time I shut a cabinet, the hardware would tug my finger. After a short time, enough was enough and I switched out my handles for knobs with no further issues. You’d never imagine a small detail such as cabinet hardware type would cause so much frustration, but it truly does make a difference.
Cabinet hardware is a great way to show off your personality and refresh your home. Use classy drawer pulls or colorful cabinet knobs to add style to your bedroom, kitchen or bathroom, or any room in the house. Choose from modern, farmhouse, classic and contemporary styles. Although knobs and pulls can be used interchangeably, knobs are usually used on doors and pulls on drawers.
We just moved into our home a few months ago and it definitely needed some updating. We decided to start in the kitchen with new appliances. Black stainless beauties 😍 That's when we really noticed how "80's" our kitchen cabinets were! They were in good shape, just wrong color. So we decided to just paint them! The hinges were terribly dirty with a film over them and brass colored. So here's a step by step how I quickly cleaned them and then painted them to match the black stainless appliances....
Cabinetmaker Steve Roca replies: Whether you're hanging new doors, as I'm doing here for a hallway cabinet, or swapping out old hinges, concealed or Euro-style hinges are a dream to install. Unlike the butt or knife hinges often used in kitchen cabinets, they can be adjusted along three axes with the turn of a screwdriver, so you can easily fine-tune the door's fit.
Based on this, you can then figure out the relationship between your cabinet doors and the frame or exposed edge of the cabinet—do the doors cover part of the frame or edge, or are they inset so that you can see that frame? Depending on whether it’s a single cabinet door or a double cabinet door, the frame or edge might be covered by one or two cabinet doors.
Hopefully you drilled for the hinges in the same location on every door, if so, then this should be simple. You really just need to measure for the top hinge. I installed my top hinge 4” down from the top of the door, so I measured 3 ½” down from the inside top of the face frame (3 ½” + ½” overlay = 4”). This step is a team effort, one person to hold the door and another person to attach the hinge to the face frame.
Knobs, which are attached with a single screw, are most frequently used on cabinets, and are available with a built-in screw, known as a one-piece knob, or with a separate top and fastener, known as a two-piece design. Modern drawer knobs are made in a variety of materials including brass, zinc, stainless steel (sometimes found in kitchens), bronze, glass, crystal, plastic, wood, and other natural and man-made materials.
There are also a couple of overlay sizes, most commonly 1 1/4″ and 1/2″. Overlay refers to the distance your door overlaps your opening. Mine didn’t measure 1 1/4″ or 1/2″, and this project still worked with my doors. If you’re looking for information on how to measure your overlay, this is not the post for you because I haven’t the faintest idea. Back to Google you go! (Sorry!)