For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
And starting to play with my new HVLP turbine spray system.  (Whenever I say HVLP turbine, I think of the movie “A Christmas Story” and how Ralphie describes his Red Ryder BB gun – “an official Red Ryder, carbine action, two-hundred shot range model air rifle.”  I think I’m equally enamored with my new gun, even if it doesn’t have a compass and a stock. 😉
Installing new Knobs and Pulls are a super easy way to update your kitchen cabinets without spending a fortune. Our kitchen cabinets didn’t even have knobs and pulls installed so I was happy to finally add new hardware. If you’re looking for an easy update for your kitchen by getting new kitchen hardware, you will like my favorite new go-to place for hardware, D. Lawless Hardware.

For pulls on a flat front cabinet, the bottom corner of the pull should be equidistant from both sides of the cabinet. For Shaker-style cabinets, the same rules apply as with knobs: center the pull on the vertical stile, with the bottom of the pull even with the top of the horizontal stile (or the top even with the bottom of the horizontal stile, for a lower cabinet). These aren’t hard and fast rules—you may want to adjust them depending on what looks best for your cabinets and hardware—but they’re a good place to start.
Before you get to hardware, it’s crucial to select your cabinet doors. The type of door you select will influence the style tremendously. The most popular styles of cabinet doors at the moment are Shaker, traditional, and modern. A Shaker-style cabinet front is a utilitarian design, with four rails and one middle, slightly recessed, center panel. It’s clean and simple design that can work well with most kitchen styles.
If you’re going for wood paneling, the process is pretty simple. Fasten the pieces together and cut to the size of your appliance. Then, remove the handles from your appliance and glue the panels onto the front using a hot glue gun. You can either paint the wood and the sides of your appliance to match your cabinets, or you can leave it as is for a natural unfinished feel. Complete the look by adding new appliance pulls to match the rest of your kitchen hardware. Appliance covers can be added to just about any kitchen appliance that has a door like a refrigerator and dishwasher.
Knobs only: The benefit of cabinet knobs is that they are typically less expensive than bar and T-pulls, and they only require one hole to be drilled into your cabinetry. A single cabinet knob can be installed on cabinet doors, but you may want to consider placing two knobs on larger drawers. Cabinet drawers are heavier than doors, therefore you may need that extra knob for ease of use. The minimalistic style of using knobs only for your cabinetry can give a very appealing look to your new kitchen.
Concealed hinges can be mounted on the surface of the door or a pressed into a “cup” that is drilled into the door.  These are often called “cup hinges”.  The cup diameter is generally 35mm but that can vary as can the drill depth required to accept the hinge.  Most concealed hinges have built in adjustability so you can slightly change the position of the door without relocating the hinge.

It’s easy to find interesting kitchen cabinet knobs for theme kitchens due to the wide selection available today. For example, there are colorful fish shaped ceramic knobs for tropical or beach themed kitchens and animal shaped cupboard pulls for a country kitchen theme. Gold colored cabinet knobs work in some kitchens although silver colored handles coordinate better with stainless steel sinks and appliances.
Concealed hinges can be mounted on the surface of the door or a pressed into a “cup” that is drilled into the door.  These are often called “cup hinges”.  The cup diameter is generally 35mm but that can vary as can the drill depth required to accept the hinge.  Most concealed hinges have built in adjustability so you can slightly change the position of the door without relocating the hinge.
Order samples, and get a few different types of styles and sizes to decide what will work best for your cabinet doors. It’s helpful to shop with a sample of your cabinet door. Ask yourself: Does my hand keeps sliding on the grip? Is it difficult to pull or get a grasp on it? Does it get greasy from my fingertips? Would I rather have a pull near the fridge but a knob near the stove? You will use this item a ton of times everyday, and you want to feel comfortable with your choice. There’s nothing worse than a cute knob that’s hard to pull open everyday.
Generally speaking, I like to see a combination of knobs and handles/pulls. Knobs or handles for the doors and handles or pulls for the drawers. If you are painting your kitchen, the extra holes can be filled, sanded, and smoothed prior to painting so you can start with a clean slate and choose any hardware for your update. I say “generally speaking” because lately I’m drawn to kitchens that have all handles like this “before” photo of a kitchen we recently updated.
×