There it is, our top 16 knobs and pulls. We were surprised there weren't any on-trend satin brass options on the list. While we've seen an up-tick in brushed and satin brass hardware's popularity, these tried-and-true stainless steel, satin nickel, and oil rubbed bronze knobs and pulls are still leading of the pack. It just goes to show that not everyone is a trend-follower. Choose your kitchen design details based on your tastes, because the trends will always change anyway!

3. Know when to use knobs over pulls. In traditional and country kitchens, putting a knob on a cabinet is not uncommon. In fact, with many cabinets, knobs may a better option than pulls. How do you know the difference? When kitchen cabinets are ornate or finely detailed, go with a knob rather than a pull. A knob is smaller and simpler and doesn’t take attention away from the design of the cabinets.
Hanging knobs on a flat-front cabinet is pretty straightforward: You’ll want to position the knob in the bottom corner (for upper cabinets) or top corner (for lower cabinets) of the door. Knobs should be placed equidistant from both sides of the cabinet. A guide like this one can help you to get the measurements right. The exact distance will depend on the look you want and the size of your knobs: Test one or two before you drill a whole kitchen’s worth of holes.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.

Pulling design from old pharmacies and soda fountains, latch hardware is that without a doubt a nostalgic throwback. Maybe not the most functional if you’re in a hurry, but handy if you’re looking for a little extra security from pets or children. Latches are another hardware type that can easily be mixed and matched, so maybe just keep them to the lesser used cabinets.
I love your site and your super helpful advice. We’re installing full overlay cabinets in our kitchen and we’re trying to select hinges for the upper cabinets — particularly the cupboard doors on the end which when closed is perpendicular to a wall. Since the door aren’t inset, I’m concerned we won’t be able to open the cupboard a full 90 degrees. Basically, the issue is how to solve the problem of the door swing? Are there any hinges that could solve this problem? I can send elevations if that helps. Thanks so much in advance!

This was a great project! I did something similar but much lazier. After installing beautiful brushed-nickel handles to dozens of drawers & cupboards, I noticed that the 30 year old hinges were dark brown and ornate (against white cabinets). Yuck ... So I opened each cabinet & used painter's tape to block off a rectangular area around each hinge. They weren't dirty, so I just painted inside the whole rectangle with silver paint. The result is sleeker and more modern, and nobody would ever notice unless they were really close. Love it!


Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.
Cabinet hardware is composed a variety of materials -- most of which are metal alloys. Brass hardware typically has a lacquer or plating applied to its surface that makes it very durable in a kitchen. It is antimicrobial and helps to reduce the spread of germs. Bronze hardware is also antimicrobial, offers a substantial look and feel, and works well for cabinets made of thicker woods. Stainless steel is another option because it is so durable. Pewter and nickel are popular choices, too. Or, you can choose knobs made from glass or crystal for a vintage look. 
If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.

I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.

If you’re looking for a more contemporary approach, tubular bars seem to be a favorite of the future. The current design couples beautifully with darker finishes and larger tiles. Tubular bars can also be used horizontally or vertically, and can be as long or short as you like. Go with a shorter bar for a more modest appeal, or make a statement with longer ones.
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
Installing new Knobs and Pulls are a super easy way to update your kitchen cabinets without spending a fortune. Our kitchen cabinets didn’t even have knobs and pulls installed so I was happy to finally add new hardware. If you’re looking for an easy update for your kitchen by getting new kitchen hardware, you will like my favorite new go-to place for hardware, D. Lawless Hardware.
Excellent post! I already knew about the different options, but it’s so nice to see it all compiled in one place. 🙂 Very handy! I love the look (or rather, lack of) of concealed hinges… but roughly $10 a pair makes me cringe. If I’ve got about 20 doors, I’m looking at $200–for HINGES! The visible hinges run about $3, for $60 total. 🙁 Hmm… debating.

This was a great project! I did something similar but much lazier. After installing beautiful brushed-nickel handles to dozens of drawers & cupboards, I noticed that the 30 year old hinges were dark brown and ornate (against white cabinets). Yuck ... So I opened each cabinet & used painter's tape to block off a rectangular area around each hinge. They weren't dirty, so I just painted inside the whole rectangle with silver paint. The result is sleeker and more modern, and nobody would ever notice unless they were really close. Love it!

Standard hardware is a breeze to install. All you need is a Phillips-Head screwdriver. Simply replace standard screws into the pre-cut holes.If the holes are pre-drilled on your cabinet drawers and you now want to place a single hole, measure the distance between the two holes and center. If your cabinet doesn’t currently have holes or hardware, knowing where to place the different size knobs on each cabinet can be tricky. If there are no holes, and you’re on your own when drilling into the corner of the cabinet door give yourself 2 1/2 to 3″ of space in the corner before you drill in a hole.

×