The importance of selecting quality hardware is impossible to overstate. As with many parts of our home, hardware is an investment. We have all seen cabinet knobs that loosen too easily and hinges that wear out. Because hardware is going to receive the bulk of a cabinet’s wear and tear, investing more in it is ultimately investing more in the life of your cabinets.

The clean, industrial look of silver produces a calm ambiance, which pairs perfectly with your white cabinets. Silver is also bright enough, where it also stands out on your cabinets and gives your kitchen that shiny and sterile feel. The majority of today’s appliances are stainless steel, so your stainless steel hardware will share that uniform look.


For oversized cabinetry you’ll obviously want to use larger hardware.  Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized.  For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches.  Some contemporary pulls are even larger than 12 inches.  That measurement is taken from the center of one screw hole to the center of the second screw hole).  Oversized knobs  are 1-1/2” or larger.
Cup pulls are a nice complement to Shaker-style cabinets, particularly in a country-style kitchen. Recessed hardware can make for a particularly elegant and modern look, but also tends to be a bit on the pricey side. Slim, modern finger pull type hardware, which mounts to the top of a drawer or the edge of a cabinet, is a nice choice for flat-front cabinets in a modern kitchen.
The clean, industrial look of silver produces a calm ambiance, which pairs perfectly with your white cabinets. Silver is also bright enough, where it also stands out on your cabinets and gives your kitchen that shiny and sterile feel. The majority of today’s appliances are stainless steel, so your stainless steel hardware will share that uniform look.
2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!

There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Hanging knobs on a flat-front cabinet is pretty straightforward: You’ll want to position the knob in the bottom corner (for upper cabinets) or top corner (for lower cabinets) of the door. Knobs should be placed equidistant from both sides of the cabinet. A guide like this one can help you to get the measurements right. The exact distance will depend on the look you want and the size of your knobs: Test one or two before you drill a whole kitchen’s worth of holes.
Finally, another popular way of opening cabinets without the use of traditional pulls or knobs is through cut-outs in the cabinetry. These are frequently found on custom cabinets where a minimalist look is desired, or where the budget is tight and saving on hardware is desirable. Cut-outs can come in a range of shapes, and are often designed to facilitate ease of opening. 
Most knobs and pulls are only a few dollars apiece but when you consider the sheer number that you’ll need, those costs add up fast. For each standard lower cabinet with two doors and one drawer, you’ll need three pieces of hardware — and two more knobs or pulls for the matching upper cabinet doors. With that in mind, here are a couple of factors to consider:
I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
Once you choose the style of hardware you want, it becomes easier to choose the right finish. There is a wide variety of cabinet hardware finishes: tarnished, polished, brushed, burnished, oil-rubbed, satin, antique or matte -- just to name a few. Stainless steel handles in a highly polished finish look great in a contemporary kitchen. Pewter and brass look more at home in a traditional setting. Bronze will patina over time, mature in appearance, and will make a bold statement in a kitchen. A black finish is dramatic on a light colored cabinet. Whatever you choose, just make sure the finish on your cabinet hardware complements the overall decor of your kitchen.

Caring for decorative hardware purchased from Cliffside Industries is easy. Use only a soft cloth dampened with water for cleaning. The most important thing to remember is never to apply any chemicals or abrasive cleaners, including all kinds of soap or detergent. Using these products damages the protective lacquer and may change the appearance of the piece. Any use of chemicals, abrasives or soaps will void your warranty.
Excellent post! I already knew about the different options, but it’s so nice to see it all compiled in one place. 🙂 Very handy! I love the look (or rather, lack of) of concealed hinges… but roughly $10 a pair makes me cringe. If I’ve got about 20 doors, I’m looking at $200–for HINGES! The visible hinges run about $3, for $60 total. 🙁 Hmm… debating.
Shaker style cabinets. The most common style of cabinet offers flexibility in design, and they work well with knobs or cup or bin pulls. Shakers are known for their simplicity and clean lines, so simple hardware is often used, such as round knobs.Traditional nickel or steel knobs or pulls are common, as well as vintage glass or ceramic knobs. Vintage pulls with exposed screws provide a classic touch or industrial feel to a new kitchen with shaker cabinets. Tubular bar pulls — which can be short or long and dramatic — modernize a traditional kitchen with shaker cabinets. Flat bar pulls offer a contemporary edge, while wire pulls keep your décor traditional. Arched and footed bar pulls offer a classic look on shaker style cabinets.
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.

These small items — doorknobs, drawer pulls, cabinet-door handles — are "the jewelry" that can add style and sparkle to any space, says New York-based interior designer Young Huh. Just as the right necklace can turn a simple dress into a fashion statement, a striking new set of knobs on an old cabinet, or vintage crystal doorknobs can bring a huge dose of style to your home with minimal expense, she says.
I have tried to find replacement hinges for my kitchen cabinets along with screws, I have gone to every home improvement store and wasn’t able to find any. The first screws I tried kept snapping the heads off as I tightened down. It didn’t matter if it was manually tightening or with an electric screw driver. Why does this keep happening? I stripped the hinges with acetone and then sprayed them with a silver paint. Love the hinges now, just not any screws. What kind do you suggest?
Ceramic knobs bring such charm to your kitchen. They’re reminiscent of a sweet country cottage, or an old world farm house. It’s not hard to imagine the scent of a freshly baked pie or loaf of bread cooling in the window. Ceramic knobs pair quite nicely with natural wood finishes and glass hutch cabinets. Wether you choose plain white or a funky pattern, ceramic knobs give your kitchen a homey flair.
Cabinetmaker Steve Roca replies: Whether you're hanging new doors, as I'm doing here for a hallway cabinet, or swapping out old hinges, concealed or Euro-style hinges are a dream to install. Unlike the butt or knife hinges often used in kitchen cabinets, they can be adjusted along three axes with the turn of a screwdriver, so you can easily fine-tune the door's fit.
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.

And starting to play with my new HVLP turbine spray system.  (Whenever I say HVLP turbine, I think of the movie “A Christmas Story” and how Ralphie describes his Red Ryder BB gun – “an official Red Ryder, carbine action, two-hundred shot range model air rifle.”  I think I’m equally enamored with my new gun, even if it doesn’t have a compass and a stock. 😉
It may take some time for you to consider what effect you would like to create with your hardware on your kitchen cabinets. In fact, some styles, patterns, and finishes are so beautiful or unique, that they become the focal point in the kitchen and a topic of conversation. Many of the ceramic and glass styles are so cleverly finished that they look too pretty to simply be part of a kitchen cabinet.
What they are: An upside-down cup-shaped pull popularized in the mid-19th century. Bin or cup pulls are a popular choice for giving a kitchen a minimalist, vintage feel, just like on these Shaker-style cabinets and drawers. Shakers originally used wood pegs, usually made from maple, cherry or pine, in keeping with their preference for simplicity and austerity. But these cup-shaped drawer pulls are considered Shaker style today, and look clean and understated along with small knobs for the doors.
I would like to use a hinge similar to the wrap around no mortise Amaroc 3175s but am disappointed to learn the poor reviews ….sloppy….bent…flimsy…not worth it…low qc import. Perhaps they were better in the past! I would be most greatful if you could recommend a better quality hinge of that style. Alternatively,Can the full inset euro cup hinge be adapted to a face frame cabinet by building out the inside lip ^
When decorating your rustic kitchen, a little bit of detail can go along way! There are many round, cast iron options that have designs that look great in rustic kitchens. If cast iron is too dark for your cabinets, look for an antique pewter finish. The detail within the hardware itself will certainly add to the look. This option also works well for a farmhouse style kitchen, giving it a great country feel.
Between your cabinets and your drawers, you may have thirty of more cabinet handles in your kitchen, which has a significant effect on the look of the room, so you will want to choose knobs and pulls that match or complement your kitchen decor. If your kitchen has a modern look, consider choosing a cabinet handle that has angles and a very simple design or a square knob. Keep in mind that you can find knobs and pulls in a number of different designs, so if you have a Tuscan-themed kitchen, you can find kitchen cabinet knobs stamped with grapes, and if you have a rustic kitchen, you can find kitchen cabinet handles made from twisted wrought iron.

Interior Door knobs and levers can range from less than $20 to $200.  You can find cabinet knobs and pulls from less than $2 each to more than $20 each.     Solid knobs and pulls are better quality than hollow hardware.  Although you generally get what you pay for with hardware, if your budget is tighter, you might want to choose less expensive cabinet hardware since it’s relatively easy for homeowners to trade it out for better quality hardware in the future.
If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.
Updating the hardware on your kitchen windows can take them from standard to standout in seconds! Typically, window sash locks and lift pulls blend in with your window color, but switching these traditional styles up with an elegant bronze or a satin nickel finish will add interest and pizzazz to your windows. You can also choose a finish that matches the rest of your kitchen hardware for a pulled together style.
Once you have decided on a style and shape for your hardware, you still need to choose the finish for your knobs and pulls. A shiny chrome finish has a modern feel, while brushed nickel or pewter may bring a more traditional look to your kitchen. Black hardware can be modern in a glossy finish or traditional with a matte finish. Many hardware lines come in several different finishes to help you find exactly the look you want.
Oh how true this is for me right now. Oh how true. Luckily I’m here :-). By the way, I can’t handle your kitchen, it’s too perfect. I’ve never seen anything like it and it’s the best thing I’ve ever seen. I’m doing a modern eclectic boho kitchen, predominately white, some wood accents, maybe darker lower cabinets, maybe gold hardware (that’s where I’m stuck), and then pops of beautiful colour like you have here. I’m excited!

Shake a can of rust-inhibiting metal spray primer for the amount of time recommended by the manufacturer. Position the can the recommended distance away from the hinges -- it varies among manufacturers. Spray a light coat of primer on the hinges and screw heads using steady, even sweeps. Make sure you spray the sides and edges. Shake the can frequently while you spray. Allow the primer to dry for the amount of time recommended by the manufacturer. Apply a second coat of primer and allow it to dry completely.
But If you don’t think of your hardware as decorative (but as purely functional) and just want your pulls and knobs to blend into the background, instead of standing out, you can choose hardware that is more subtle.  Choose dark hardware for darker cabinets or silver or clear hardware for white or light cabinets.   Alternatively, you can forgo cabinet pulls and knobs all together, which will give a much more contemporary  look.
Once you have decided on a style and shape for your hardware, you still need to choose the finish for your knobs and pulls. A shiny chrome finish has a modern feel, while brushed nickel or pewter may bring a more traditional look to your kitchen. Black hardware can be modern in a glossy finish or traditional with a matte finish. Many hardware lines come in several different finishes to help you find exactly the look you want.
Hi, Randi! I love all your comments. They are MAKING my day! (Especially how can I be old enough to have a daughter with her own place lol This daughter also has two kids which makes me grandma. Oy. Yes, I’m THAT old!) Anyway, I’m so glad you commented and shared about your kitchen. I’m so glad you’re going for what you want! Sometimes we do indeed get paralyzed but we have to remember who our homes are for…..and that’s US! I think we want to enjoy our kitchen especially, since most of us spend time in there with our families, or at least cooking for our families!
For those considering putting their home on the market soon, it’s likely your looking at what parts of your home to freshen up to impress potential buyers. Changing your cabinet hardware to a traditional option can make a huge difference. Small, ridged handles in a dark finish or square knobs is a cabinet hardware pick that will stand the test of time.
I watch you every Sunday morning. I used to help run a construction co. here in Knoxville,TN. I am now my Moms cargiver(87). I lost my dear sweet husband last November. I am trying to sale my house. I am just stressed trying to find replacement wrap-around hinges and pulls for my kitchen and bath. I also am going to replace my laminate tops. Do you have any sources I should check. You two remind me of my sweet dad and me from years ago. Please HELP!!!!!!
I have tried to find replacement hinges for my kitchen cabinets along with screws, I have gone to every home improvement store and wasn’t able to find any. The first screws I tried kept snapping the heads off as I tightened down. It didn’t matter if it was manually tightening or with an electric screw driver. Why does this keep happening? I stripped the hinges with acetone and then sprayed them with a silver paint. Love the hinges now, just not any screws. What kind do you suggest?
The choice between cabinet pulls and knobs isn’t easy — both come with positives and negatives. Keep in mind that you’ll be using your knobs or pulls every day. Whatever you choose should feel natural in your hand and flow with the décor of the room. You should consider your kitchen’s décor and style, the look you want to achieve, your budget, ease of cleaning, ease of use, the weight of your drawers and more.
Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!
×