There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.
Dreamy DIY: Have you ever seen something that makes you want to break out the craft kit and get to down to business? Well these leather drawer pulls with brass rivets are so luxuriously handsome it makes us want to rip out and redo every single pull in the house. I can only imagine how delightful these will begin to look when worn with use — a little imperfection to balance and roughen up such a posh space.
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
Choosing your kitchen hardware is a great way to customize the look of your cabinetry and drawers. From pulls to knobs and handles, you can get your kitchen cabinet hardware in almost any shape you desire. Choosing the right shape mainly depends on personal preference. I once had handles that we’re a bit snug on my finger when I opened a cabinet. As a result, every time I shut a cabinet, the hardware would tug my finger. After a short time, enough was enough and I switched out my handles for knobs with no further issues. You’d never imagine a small detail such as cabinet hardware type would cause so much frustration, but it truly does make a difference.

This was a great project! I did something similar but much lazier. After installing beautiful brushed-nickel handles to dozens of drawers & cupboards, I noticed that the 30 year old hinges were dark brown and ornate (against white cabinets). Yuck ... So I opened each cabinet & used painter's tape to block off a rectangular area around each hinge. They weren't dirty, so I just painted inside the whole rectangle with silver paint. The result is sleeker and more modern, and nobody would ever notice unless they were really close. Love it!
Hinges creak, wear out, discolor or even break over the years. They can also bend. This makes cabinet doors fit poorly. New hinges can update any set of cabinet doors no matter how old they are, and real estate agents often recommend replacing old hardware to help sell your home. Whether you're moving, doing a remodeling job or your kitchen just needs a bit of TLC, you can change your hinges out in one afternoon. Hinges are designed to fit square on the side of the door, making it simple to get the hinge alignment correct -- even if your doors are older than you are.

If you’re going for wood paneling, the process is pretty simple. Fasten the pieces together and cut to the size of your appliance. Then, remove the handles from your appliance and glue the panels onto the front using a hot glue gun. You can either paint the wood and the sides of your appliance to match your cabinets, or you can leave it as is for a natural unfinished feel. Complete the look by adding new appliance pulls to match the rest of your kitchen hardware. Appliance covers can be added to just about any kitchen appliance that has a door like a refrigerator and dishwasher.
Once you’ve worked out which types of hardware are comfortable to use, it’ll be time to start thinking about shapes in relation to the shape of your cabinetry. In general, knob and pull styles should be matched to kitchen cabinet styles. What this means is if you have selected a plain cabinet style, for example, shaker or flat, ultra-modern doors, then you’ll want square, plain hardware to match — perhaps something like Emtek’s brass bar knob or a similar style. Recessed panel doors or doors with curving and intricate trim will often do well with more ornate hardware styles.
1. Stick with the theme. The hardware you choose speaks to your theme in the same way your kitchen cabinets do. Which hardware works best with different themes? Sleek, tubular pulls, like those in our Torino collection, complement the streamlined look in modern and contemporary kitchens. Traditional cabinets tend to have more detail and benefit from simple, smooth knobs, like the Projectionin style from our Drake collection. French country can benefit from hardware with an antique look, like our Windermere collection that comes in gun metal, rubbed bronze and brush pewter.
Hidden hinges also come in a soft-close style if you’re one of those people who want the latest and greatest. (Is it really that bad to hear a door close?) My new cabinets came with soft close hinges that I personally could take or leave.  I still find myself trying to shut them all the way instead of letting them do their thing. You might not want soft-close hinges if you’re the type who likes to slam things when irritated. (Just a thought.)
This was a great project! I did something similar but much lazier. After installing beautiful brushed-nickel handles to dozens of drawers & cupboards, I noticed that the 30 year old hinges were dark brown and ornate (against white cabinets). Yuck ... So I opened each cabinet & used painter's tape to block off a rectangular area around each hinge. They weren't dirty, so I just painted inside the whole rectangle with silver paint. The result is sleeker and more modern, and nobody would ever notice unless they were really close. Love it!
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
However, much like the keys of the grand piano, hardware commands the proceedings in cabinetry. It is generally the only part of a cabinet we touch, and its hinges account for all of its moving parts. As it is our main method of interacting with the cabinet, its feel, sturdiness and functionality are going to play a large role in how we view the functionality of the kitchen.

There are also a couple of overlay sizes, most commonly  1 1/4″ and 1/2″. Overlay refers to the distance your door overlaps your opening. Mine didn’t measure 1 1/4″ or 1/2″, and this project still worked with my doors. If you’re looking for information on how to measure your overlay, this is not the post for you because I haven’t the faintest idea. Back to Google you go! (Sorry!)
Even if you have multiple light fixtures in your kitchen, don’t worry about finding new fixtures that match exactly. By varying the design slightly, each light fixture will stand out and create visual interest in your kitchen. However, when choosing one-off pieces, just be sure to stick with a theme for your lighting so it looks purposeful. In other words, if you’ve picked a rustic metal chandelier for over your dining table, choose something that is also rustic inspired to hang over your kitchen sink, like a simple pendant light, and keep that theme going with other lighting choices as well.
What is the existing decor of your kitchen or bathroom? For instance, if your kitchen has a white, Scandinavian minimalist aesthetic, you should try matching your hardware with it — in that case, perhaps something slender, jet-black and low-profile. Mismatching styles can look “off” and can create a confused sense of the room’s personality. However, it can also be done well. We’ll go into more depth on this below.
That being said, buying every make and model turned out to be a good idea. I was pretty pumped when I installed my first door…until I shut the door and there was a gap the size of Kansas where the door didn’t cover my opening. I should have taken a picture because it was pretty hilarious-looking. Wrong hinge. So I removed the 1 1/4″ overlay hinge, installed the 1/2″ overlay and was good to go. The holes that need to be drilled in the door will be the same in size, depth and location regardless of your overlay measurement.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
Dreamer, thinker, + lemon squeezer; you'll usually find me clutching a mug of coffee, glue gun, fandeck of paint colors, and a child at any given time. This mom of two (and wife to one) loves to share freshly squeezed ideas for home and family. Join the adventure as we learn most lemons can indeed become lemonade-- with generous amounts of sweetness, perspective, and love.
There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.
Dreamy DIY: Have you ever seen something that makes you want to break out the craft kit and get to down to business? Well these leather drawer pulls with brass rivets are so luxuriously handsome it makes us want to rip out and redo every single pull in the house. I can only imagine how delightful these will begin to look when worn with use — a little imperfection to balance and roughen up such a posh space.
×