The homeowner has already installed a new tile backsplash, and will also be replacing the floors with new tile and painting the walls once I’m finished with the cabinets. But the homeowner was concerned about the hinges standing out against a light cabinet color. A cabinet refresh is going to help tie the updates together, and when we got to talking about the hinges, I did some research, and found a great local woodworker to help change the hinges from exposed to concealed.
For knobs on a cabinet with a stile, like Shaker-style cabinets, allow the stile to be a guide for hanging the knob. If the knob is too large to comfortably fit in the corner where the two stiles meet, then hang the knob centered on the vertical stile, with the bottom edge of the knob aligned with the top of the intersecting horizontal stile. (Or the top of the knob aligned with the bottom of the stile, for lower cabinets). The knobs in this kitchen from Ivory Lane are a good example.
It’s definitely possible to change out the hinges without redoing the cabinets – you would just have to make sure that the holes on the frames where the old hinges were, are able to be filled and touched up so that they’re not obvious. I’m not sure of the cost, but hinges aren’t cheap, and I definitely recommend using a carpenter to do the work. Hinges can be maddening!
but wouldn’t the holes from the original overlay hinges show? I have stained maple cabinets and would love to get rid of the overly hinges but I have two problems. the holes will show, and also, the doors are smaller than what is typical for hidden hinges. All the kitchen cabinetry that I have seen with hidden hinges have cabinet doors that literally touch. inotherwords, they completely cover the cabinet. any suggestions? should I replace the doors? would I save money doing that?
Hidden hinges, or European (Euro) hinges as they’re called, aren’t difficult to install, and were part of my mini kitchen update. My kitchen is small, and in order to gain storage space, I switched the 30″ upper cabinets to 42″ ones, but kept some of the existing base cabinets. The very shiny, visible hinges on the base cabinets were a dead giveaway as to which cabinets were the moldy oldies. Here are the originals.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door.
What they are: Art objects as much as pulls, these knobs draw attention. Placed in the center, they draw your eye to the detailing of the worn wood here. Search salvage yards for antique ones and don’t be afraid to spring for the few knobs you’ll need. If you can’t find this sort of door detailing, you can create a similar effect by placing a medallion behind each knob in the center of your doors. Look for antitwist pins to keep the knob from spinning (in fact, do this with any round knob).
“What is your overall style? Traditional, contemporary, arts and crafts, eclectic, cottage, French, Mediterranean, Western, Art Deco or coastal,” asks Brandino Brass co-owner Eric Brandino. He encourages clients to think about the style of their home or the style they would like to incorporate. “Is there a consistent style throughout or does it vary from room to room? Transitional style has been one of the most popular looks recently,” he says of what’s trending in hardware. “Clean lines with just a touch of traditional features and finishes, such as an unlacquered brass or bronze.”
A common choice is to use knobs for all drawers and pulls for all doors (or vice versa). The problem with knobs is they are harder to grip and fingernails tend to mar the cabinet door. It is much more comfortable to open a drawer using a pull, which allows the whole hand to grab instead of only your fingertips. We generally use pulls (no nobs whatsoever) in our kitchen designs.
Let’s talk first about metals. As a general rule, I like to keep the different metals in a kitchen to no more than two. If you have stainless steel appliances, that counts as one metal. So that leaves one other metal you can bring into a kitchen. If you’ve got brass light fixtures, that’s your one other metal. Your new hardware should be nickel or brass.