One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.
This was a great project! I did something similar but much lazier. After installing beautiful brushed-nickel handles to dozens of drawers & cupboards, I noticed that the 30 year old hinges were dark brown and ornate (against white cabinets). Yuck ... So I opened each cabinet & used painter's tape to block off a rectangular area around each hinge. They weren't dirty, so I just painted inside the whole rectangle with silver paint. The result is sleeker and more modern, and nobody would ever notice unless they were really close. Love it!
Ultimately, you should choose your hardware according to your personal preferences, kitchen style and goals for functionality. If you’re concerned about resale value, recognize that the most popular hardware finishes are satin, nickel and bronze. There are no hard-set rules to follow when it comes to adding the final details to your kitchen, and many people choose a combination of knobs and pulls. If you’re unsure of which to choose for your kitchen cabinets or drawers, it’s wise to examine the pros and cons of both.
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
Nickel and chrome have about the same level of durability, but chrome is sometimes a bit more expensive. Brushed or matte finishes hide fingerprints and watermarks better than shiny finishes. You’ll generally find a lot more hardware options in brushed nickel than in chrome or stainless steel. Poor quality nickel and chrome finishes can peel and flake over time. Stainless steel, which is usually matte, is the most durable of the silver finishes and as such, is usually the most expensive. True stainless steel hardware is typically made from a full thickness metal alloy and it’s not just plated on the surface like nickel and chrome are.
For those considering putting their home on the market soon, it’s likely your looking at what parts of your home to freshen up to impress potential buyers. Changing your cabinet hardware to a traditional option can make a huge difference. Small, ridged handles in a dark finish or square knobs is a cabinet hardware pick that will stand the test of time.
What they are: Sturdy yet glamorous pulls that complement many styles of cabinetry. Here linear flat bar pulls not only underscore the contemporary feel of the kitchen, but oversize pulls eliminate the need for two pulls on a wide drawer. A good rule of thumb is to use two knobs or pulls on drawers 18 inches wide or wider. But if you choose superwide pulls like these, one is enough.
Once you’ve worked out which types of hardware are comfortable to use, it’ll be time to start thinking about shapes in relation to the shape of your cabinetry. In general, knob and pull styles should be matched to kitchen cabinet styles. What this means is if you have selected a plain cabinet style, for example, shaker or flat, ultra-modern doors, then you’ll want square, plain hardware to match — perhaps something like Emtek’s brass bar knob or a similar style. Recessed panel doors or doors with curving and intricate trim will often do well with more ornate hardware styles.
If you think about it, you open your cabinet doors multiple times a day. Over a few years, that can take a toll on those hinges holding your doors in place. Replacing them with hinges that are made from a quality material like solid brass will not only help your cabinet doors function better, but it will make them look better, too! Choose a hinge color that matches the other hardware in your kitchen for a unified look and feel. For easy installation, look for hinges that are adjustable so you can use the same hinges to fit multiple sized doors and cabinets. This small change will make your cabinets look updated and keep them functioning properly for years to come.
2. Keep finishes cohesive. You’ll find hardware in a range of finishes from brushed nickel to brass. While mixing and matching the hardware around your kitchen is fine, you should try to maintain the same finish and keep colors as close as possible. Sometimes you’re forced to buy hardware from more than one retailer, but when doing so make sure you keep finishes cohesive.
My go-to shop for all of my hardware needs is D.Lawless Hardware – I’ve been using hardware from there for a while now and it’s always the best quality at the lowest prices. They sell so many other awesome products too. Everything from knobs and pulls, drawer slides and systems, to wood appliques, trim, DIY, craft supplies, outlet covers, and so much more!
“People come in and say they have a ‘standard’ door,” says Renee Genereux of the Brandino Brass team. “But there is no such thing as standard. You need to know your door thickness, how does it swing, what’s the width, what kind of holes do you have.” Avoid multiple visits to the hardware store because you don’t have all of the information and measurements you need. “We give them all of the questions to answer and then they come back with all of it.” Call Brandino Brass ahead of time to ask what you need to know for your visit or check out the sheet below as handy guideline for getting to know your doors and cabinets better.
It’s important to choose hardware that will complement the rest of your kitchen décor and accentuate its worthy features. Generally, most people want their cabinet and drawer hardware to coordinate with the handles on their appliances. The colors should work well together, and the finishes shouldn’t clash. Drastically different shapes can also make your kitchen feel cluttered. You should use functionality and your personal preference to approach choosing knobs vs. pulls, but there are a few general guidelines to follow that correlate with your style of cabinets.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!